📘 Lecture 6 — Voltage divider, Current divider
📖 Overview: This lecture covers the voltage divider rule for series circuits and the current divider rule for parallel circuits. It explains how to calculate voltage drops across individual resistors in series and current through individual branches in parallel using simple ratio formulas, with multiple worked examples demonstrating both principles.
🗂️ Topics Covered
The lecture introduces voltage division rule for calculating voltage drops across series resistors, including the method for two voltage drops in series where one can be found by subtraction. It then covers current division for two parallel resistances, explaining how currents divide inversely as branch resistance. Multiple examples demonstrate voltage division across various series resistor combinations and current division in parallel circuits, including cases with short circuits and combined series-parallel configurations. The lecture concludes with an example calculating power absorbed by each element in a circuit.
📝 Lecture Summary
Voltage divider rule for series circuits
The voltage drop across a resistor in a series circuit can be found by multiplying the total voltage by the ratio of that resistor's value to the total series resistance. The formula is V = (R/Rt) × Vt, where V is the voltage across the resistor, R is the resistor value, Rt is total series resistance, and Vt is total applied voltage.
🔑 Definition — Voltage divider rule: The voltage across a resistor in a series circuit equals the total voltage multiplied by the ratio of that resistor's resistance to the total series resistance.
📐 Formula: Vₓ = (Rₓ / Rₜₒₜₐₗ) × Vₜₒₜₐₗ → The voltage across a specific resistor is proportional to its share of the total resistance.
📌 Example: For a 9kΩ and 3kΩ resistor in series with a 12V source: V₁ (across 9kΩ) = (9kΩ / (9kΩ+3kΩ)) × 12V = (9/12) × 12 = 9 volts V₂ (across 3kΩ) = (3/12) × 12 = 3 volts.
📌 Example: For 50kΩ, 30kΩ, and 20kΩ resistors in series with 200V: V₅₀ₖ = (50k/100k) × 200 = 100V V₃₀ₖ = (30/100) × 200 = 60V V₂₀ₖ = (20/100) × 200 = 40V
📌 Example: In a circuit with 10V source in parallel with 10kΩ, the same 10V appears across the 10kΩ resistor. When 4kΩ is in series with another 4kΩ, voltage division gives V = (4/8) × 10 = 5 volts.
💡 Why this matters: The voltage divider is fundamental for designing reference voltages, sensor circuits, and biasing networks in electronics.
Two voltage drops in series
For two series resistances, it is not necessary to calculate both voltages separately. After finding one voltage drop, subtract it from the total voltage to find the other. For example, if Vt is 48V across two series resistors and V₁ is 18V, then V₂ must be 48V - 18V = 30V.
Current divider with two parallel resistances
It is often necessary to find individual branch currents in a circuit without knowing the branch voltage. This is solved using the fact that currents divide inversely as branch resistance. The formula is I₁ = Is × R₂/(R₁ + R₂), where Is is the total source current entering the parallel combination.
🔑 Definition — Current divider rule: In a parallel circuit, the current through one branch equals the total current multiplied by the ratio of the opposite branch resistance to the sum of both resistances.
📐 Formula: I₁ = Iₛ × R₂/(R₁ + R₂) → Current through R₁ depends on the value of R₂ (the other branch), not R₁.
📌 Example: For 4Ω and 2Ω resistors in parallel with 30A total current: I through 4Ω = (2Ω/(2Ω+4Ω)) × 30A = (2/6) × 30 = 10A I through 2Ω = (4Ω/(2Ω+4Ω)) × 30A = (4/6) × 30 = 20A
📌 Example: For a circuit where 30A enters a node with 1kΩ and 4kΩ parallel branches, the current through 1kΩ is I = (4k/(4k+1k)) × 30 = (4/5) × 30 = 24A.
📌 Example: To find current through 4kΩ resistor when current divides at Node A between 4kΩ and series combination of 2kΩ+2kΩ=4kΩ: I = (4k/(4k+4k)) × 12 = (4/8) × 12 = 6A.
📌 Example: For a circuit with -6A current source (direction downward) feeding 4kΩ and 8kΩ parallel combination: I through 8kΩ = (4k/(4k+8k)) × (-6) = (4/12) × (-6) = -2A.
💡 Why this matters: Current division is essential for designing current measurement circuits and analyzing parallel loads in power systems.
Finding voltage using current division
To find voltage across a resistor, first find the current through it using current division, then apply Ohm's Law (V = IR).
📌 Example: Find voltage across 3kΩ resistor. At point A, current divides between 12kΩ and series combination of 3kΩ+1kΩ=4kΩ. First find current through series combination: I = (12k/(4k+12k)) × 1A = (12/16) × 1 = 0.75A Same current flows through both series resistors, so voltage across 3kΩ: V = 0.75 × 3k = 2250 volts.
Circuit reduction and voltage calculation
Complex circuits can be simplified by combining series and parallel resistors step by step to find voltages or currents.
📌 Example: Find V in a circuit with 1A source feeding 2kΩ in series with a parallel combination. Working from right to left:
- 4kΩ + 14kΩ = 18kΩ (series)
- 18kΩ || 9kΩ = (18×9)/27 = 6kΩ (parallel)
- 6kΩ || 12kΩ = (6×12)/18 = 4kΩ (parallel)
- 2kΩ + 4kΩ = 6kΩ (series total) Voltage V = IR = 1A × 6kΩ = 6000 volts.
Effect of short circuits on current division
A short circuit (zero resistance path) will divert all current away from parallel resistors.
📌 Example: Find current through 6kΩ resistor. At point C, current should divide between paths, but due to a short circuit between C and D, all current flows through the short. By current division: I = (6k/12k) × 1 = 0.5A.
📌 Example: Calculate current through 5kΩ resistor. Since 5kΩ has zero resistance in parallel (short circuit), current arriving at node C takes the zero resistance path and no current passes through 5kΩ.
Voltage across resistor with current source direction change
When a current source direction is reversed, the current value becomes negative for calculations.
📌 Example: Calculate voltage across 4kΩ resistor with negative current source (-2A). Current divides between 3kΩ and series combination of 2kΩ+4kΩ=6kΩ: I through 6kΩ = (3k/(3k+6k)) × (-2) = (3/9) × (-2) = -0.66A Voltage across 4kΩ = 0.66 × 4k = 2640 volts.
Voltage division with parallel simplification
Parallel resistors can be reduced to an equivalent resistance before applying voltage division.
📌 Example: Calculate voltage across 12kΩ resistor. First, 4kΩ is in parallel with 6V source so same voltage appears (omit from circuit). Then 12kΩ || 6kΩ = (12×6)/(12+6) = 4kΩ. Apply voltage division: V₄ₖ = (4k/(4k+2k)) × 6V = (4/6) × 6 = 4V. Since 4kΩ is the parallel combination of 6kΩ and 12kΩ, same voltage appears across 12kΩ, so V₀ = 4V.
Power absorbed by each element
Power in each element can be calculated using P = VI, P = V²/R, or P = I²R after finding all voltages and currents.
📌 Example: For a circuit with 20V source and resistors (1.5Ω, 14Ω, 2Ω, 4Ω, 2.5Ω): P₂₀ᵥ = -(20)(4) = -80W (negative indicates power supplied by source) V₁.₅ = 4(1.5) = 6V, p₁.₅ = (6²)/1.5 = 24W V₁₄ = 20 - 6 = 14V, p₁₄ = 14²/14 = 14W i₂ = (6/1.5) - (14/14) = 3A, V₂ = 2(3) = 6V, p₂ = 6²/2 = 18W V₄ = 14 - 6 = 8V, p₄ = 8²/4 = 16W i₂.₅ = (6/2) - (8/4) = 1A, V₂.₅ = 2.5(1) = 2.5V, p₂.₅ = 2.5²/2.5 = 2.5W Is = -1A
⭐ Key Takeaways
The voltage divider rule (Vₓ = Rₓ/Rₜ × Vₜ) allows quick calculation of voltage drops across individual resistors in series circuits, while the current divider rule (I₁ = Iₛ × R₂/(R₁+R₂)) finds branch currents in parallel circuits where currents divide inversely to resistance. When two resistors are in series, finding one voltage drop and subtracting from the total gives the other drop. Complex circuits should be simplified by combining series and parallel resistors before applying divider rules. Short circuits (zero resistance) will divert all current away from parallel paths. Power calculations require finding all voltages and currents first, then applying P=VI, P=V²/R, or P=I²R.
🧠 Quick Revision Questions
- If three resistors of 10kΩ, 20kΩ, and 30kΩ are in series with a 60V source, what is the voltage across the 30kΩ resistor?
- In a parallel circuit with 12A total current and two branches of 3Ω and 6Ω, what current flows through the 3Ω resistor?
- Why does a short circuit in parallel with a resistor cause no current to flow through that resistor?
- If V₁ is 15V across a series resistor and the total voltage is 50V, what is V₂?
- When a current source direction is reversed in a circuit, what happens to the sign of the current values used in calculations?
📘 Lecture 7 — Kirchhoff's Laws Kirchhoff's Current Law (KCL)
📖 Overview: This lecture introduces Kirchhoff's Current Law (KCL) and demonstrates its application in solving circuit problems. Understanding KCL is fundamental for analyzing complex circuits as it governs how current flows at junctions. The lecture also covers related circuit analysis techniques including voltage division, current division, and series-parallel reduction.
🗂️ Topics Covered
The lecture covers Kirchhoff's Current Law (KCL) with definitions and assumptions, node and branch analysis techniques, and voltage/current division rules. It includes multiple worked examples demonstrating KVL and KCL applications for calculating unknown voltages, currents, and source values in resistive circuits. Key concepts like ground reference, loop definition, and the formula for writing node equations (N-1 equations) are also explained.
📝 Lecture Summary
Example: Calculate source voltage Vs given voltage between nodes A and B is 4V
The voltage between node A and B is given as 4V. Using the voltage division rule, the source voltage can be calculated. The formula used is V = (R/Rt)Vs, where V is the voltage across a specific resistor, R is that resistor value, and Rt is the total series resistance.
🔑 Definition — Voltage Division Rule: In a series circuit, the voltage across any resistor is proportional to its resistance relative to the total series resistance. 📐 Formula: V = (R/Rt)Vs → The voltage across a resistor equals its resistance divided by total resistance, multiplied by the source voltage. 📌 Example: Given V = 4V across 4kΩ resistor with total series resistance of 12kΩ (4kΩ + 8kΩ): 4 = (4/12)Vs, so Vs = (12 × 4)/4 = 12 Volts.
Example: Calculate the source current Is
The voltage across a 3kΩ resistor is 12V. Using Ohm's Law, the current through it is calculated. This current flows through the series combination of 3kΩ and 9kΩ resistors. The current division rule is then applied to find the source current.
💡 Why this matters: Current division allows us to find how current splits between parallel branches, which is essential for analyzing complex networks.
📐 Formula: I = V/R → Current equals voltage divided by resistance. 📌 Example: I = 12/3k = 4mA through the 3kΩ resistor. After combining series resistors (3k+9k=12k and 2k+4k=6k), by current division: I = (6k/(12k+6k))Is, so 4mA = (6k/18k)Is, giving Is = 12mA.
Example: Calculate the source voltage Vs
Starting from a known 4V across a 2kΩ resistor, the current through it is found using Ohm's Law. This same current flows through the series combination of 2kΩ and 4kΩ resistors, allowing calculation of the voltage across 4kΩ. Series and parallel combinations are used to simplify the circuit and find Vs using voltage division.
📌 Example: I = 4/2k = 2mA. Voltage across 4kΩ = 2mA × 4kΩ = 8V. Total voltage across 2kΩ and 4kΩ = 4V + 8V = 12V. After combining series resistors (4k+2k=6k) and parallel (6k||6k = 3k), Vs = 12 × (12/3) = 48V.
Example: Calculate the voltage across 4kΩ resistor
This example demonstrates multiple series-parallel reductions to find an equivalent circuit. Using successive parallel combinations (12k||4k = 3k, 12k||6k = 4k, 12k||4k = 3k), the circuit is simplified. Voltage division is applied twice to find the voltage across the target resistor.
📌 Example: After reducing the circuit, by voltage division: V across equivalent 3kΩ = (3/6) × 12 = 6V. Then V across 3kΩ = (3/12) × 6 = 1.5 volts. This same voltage appears across the 4kΩ resistor.
Kirchhoff's Current Law (KCL)
Kirchhoff's Current Law states that the sum of all currents entering a node equals the sum of all currents leaving the node. It can also be defined as the sum of entering currents plus the sum of leaving currents equals zero.
🔑 Definition — Node: The junction of two or more than two elements; a point of connection between circuit elements. 🔑 Definition — Branch: The distance or link between two nodes. 🔑 Definition — Loop: The closed path for current flow in which no node is encountered more than once.
ASSUMPTIONS:
- All entering currents are taken as negative.
- All leaving currents are taken as positive.
Formula for Writing Equations: Number of equations in node analysis = N - 1, where N is the number of nodes.
🔑 Definition — Ground: A common or reference point among all nodes without insertion of any component between them.
Example: Find values of I₁, I₂, I₃, I₄
Assuming currents leaving the node are positive, KCL equations are written for each node.
📌 Example:
- Node 1: -I₁ + 0.06 + 0.02 = 0, so I₁ = 0.08A
- Node 2: I₁ - I₄ + I₆ = 0, so 0.08 - I₄ + I₆ = 0, therefore -I₄ + I₆ = -0.08A
- Node 3: -0.06 + I₄ - I₅ + 0.04 = 0, so I₄ - I₅ = 0.02A
- Node 4: -0.02 + I₅ - 0.03 = 0, so I₅ = 0.05A
- Substituting I₅ in node 3: I₄ - 0.05 = 0.02, so I₄ = 0.07A
- Substituting I₄ in node 2: -0.07 + I₆ = -0.08, so I₆ = -0.01A
Example: Find Vx, Iin, and Is
This example combines Kirchhoff's Voltage Law (KVL) and Kirchhoff's Current Law (KCL) to find unknown values in a circuit containing dependent sources.
📌 Example: (a) By KVL: -2 + Vx + 8 = 0, so Vx = -6V (b) By KCL at the top right node: Is + 4Vx = 4 - Vx/4, so Is + 4(-6) = 4 - (-6/4), therefore Is = 29.5A (c) Iin = 1 + Is + Vx/4 - 6 = 1 + 29.5 + (-6/4) - 6 = 23A
⭐ Key Takeaways
Kirchhoff's Current Law is the fundamental principle that current entering a node equals current leaving it, with entering currents taken as negative and leaving as positive. The number of node equations needed equals the number of nodes minus one (N-1). Voltage division (V = R/Rt × Vs) and current division are essential tools for simplifying circuits with series and parallel combinations. Ground serves as a common reference point for voltage measurements without any component between nodes. Combining KVL and KCL enables solving for unknown voltages, currents, and source values even in circuits containing dependent sources.
🧠 Quick Revision Questions
- State Kirchhoff's Current Law in two different ways.
- What is the formula for the number of equations in node analysis?
- How is ground defined in circuit analysis?
- In KCL, what sign convention is used for entering and leaving currents?
- When combining KVL and KCL, what additional circuit elements can be solved for that KCL alone cannot handle?
📘 Lecture 8 — (Application of Nodal Analysis)
📖 Overview: This lecture focuses on applying Kirchhoff's Current Law (KCL) to write nodal equations for various circuits. Through numerous examples, it demonstrates how to systematically formulate KCL equations at different nodes to solve for unknown currents and voltages, emphasizing the practical use of nodal analysis in circuit theory.
🗂️ Topics Covered
The lecture covers writing KCL equations for multiple nodes in various circuits, calculating unknown currents using nodal analysis, solving for node voltages to find specific currents like I₀, determining voltage values that satisfy given conditions, and computing power absorbed by resistors using nodal analysis results.
📝 Lecture Summary
Example: Write KCL equations for all nodes.
For node 1: I₁ + I₂ – I₅ = 0
For node 2: -I₂ + I₃ - 50I₂ = 0
For node 3: -I₁ + 50I₂ + I₄ = 0
For node 4: I₅ – I₃ – I₄ = 0
Example Write KCL equations for all nodes.
For node A: 10mA is entering the node and the source current Iₜ is leaving and 60mA is also entering.
So for node A: Iₜ - 60mA – 10mA = 0
For node B: 60mA – 40mA – 20mA = 0
Example Write KCL equation for node A.
By KCL the equation for node A: -12mA + 4mA + I = 0
Example Write KCL equation for node A and node B.
For node A: -I₁ + I₂ + 3mA = 0
For node B: -12mA + 4mA + I₁ = 0
Example Write KCL equation for node A.
For node A: -10Iₓ + Iₓ + 44mA – 12mA = 0
Example Write KCL equation for node A.
For node A equation will be by KCL: Iₓ + 10Iₓ – 44mA = 0
Example Calculate the values of I₁ and I₂.
We want to calculate the values of I₁ and I₂.
For node A: 4mA + 8mA - I₁ = 0 → I₁ = 12mA
Now for I₂, for node B: -8mA + 2 mA + I₂ = 0 → I₂ = 6mA
Example Calculate the values of I₁, I₂, and I₃.
We want to calculate the values of I₁, I₂, and I₃ using node analysis.
For node A: -I₁ – I₂ + 8mA = 0 → -I₁ – I₂ = -8mA
For node B: I₂ + I₃ + 4mA = 0 → I₂ + I₃ = -4mA
For node C: -I₃ + 2mA – 8mA = 0 → I₃ = -6mA
Putting the value of I₃ in equation of node B: I₂ - 6mA = -4mA → I₂ = 2mA
Putting the value of I₂ in equation of node A: -I₁ – 2mA = -8mA → I₁ = 6mA
Example: Find the KCL equations for node A, node B, node C and node D.
For node A: -5mA + 8mA + 4mA = 0
For node B: I₁ – I₂ + 5mA = 0
For node C: -I₁ – 2mA + 3mA – 8mA = 0
For node D: -4mA – 3mA + I₃ = 0
Example Calculate the current I₀.
At node 1: (V₁/12k) + ((V₁ – V₂)/10k) = 6mA
5V₁ + 6V₁ – 6V₂ = (60k)(6mA) → 11V₁ – 6V₂ = 360
At node 2: (V₂/3k) + (V₂/6k) + ((V₂ - V₁)/10k) = 0
10V₂ + 5V₂ + 3V₂ - 3V₁ = 0 → 18V₂ - 3V₁ = 0 → 6V₂ – V₁ = 0
Equating equations:
33V₁ - 18V₂ = 1080
-3V₁ + 18V₂ = 0
30V₁ = 1080 → V₁ = 36 volts
6V₂ - 36 = 0 → V₂ = 6 volts
I₀ = V₂/6k = 6/6k = 1mA
🔑 Definition — I₀: The current through the 6kΩ resistor, calculated as V₂/6k.
Example: Use nodal analysis to determine the value of V₂ that will result in V₁ = 0
If V₁ = 0, the dependent source is a short circuit and we may redraw the circuit.
At NODE 1: 4 - 6 = V₁/40 + (V₁ - 96)/20 + (V₁ - V₂)/10
Since V₁ = 0, this simplifies to: -2 = -96/20 - V₂/10
So that V₂ = -28V
Example Use nodal analysis to find V₁ and V₂, compute the power absorbed by 6Ω resistance.
Designate the node between the 3Ω and 6Ω resistors as node X, and the right hand node of the 6Ω resistor as node Y. The bottom node is chosen as the reference node.
Writing the two nodal equations:
NODE X: -10 = (Vₓ - 240)/3 + (Vₓ - Vᵧ)/6
NODE Y: 0 = (Vᵧ - Vₓ)/6 + Vᵧ/30 + (Vᵧ - 60)/12
Simplifying: -180 + 1440 = 9Vₓ – 3Vᵧ [1]
10800 = -360Vₓ + 612Vᵧ [2]
Solving: Vₓ = 181.5V and Vᵧ = 124.4V
Thus, V₁ = 240 - Vₓ = 58.50V and V₂ = Vᵧ - 60 = 64.40V
The power absorbed by the 6Ω resistor is (Vₓ - Vᵧ)² / 6 = 543.4 W
📐 Formula: Power absorbed by a resistor = V²/R = (Vₓ - Vᵧ)² / 6 → The power dissipated in the 6Ω resistor, calculated using the voltage difference across it.
💡 Why this matters: This example demonstrates how nodal analysis can be used not only to find node voltages but also to compute power dissipation in circuit elements, a critical calculation in circuit design and analysis.
⭐ Key Takeaways
KCL states that the sum of currents entering a node equals the sum of currents leaving that node, which forms the foundation of nodal analysis. When writing nodal equations, you must account for all sources (current and voltage) and all resistors connected to each node, carefully considering current directions. Nodal analysis is a systematic method: identify all nodes, designate one as reference, write KCL equations for each non-reference node, and solve the resulting system of equations. The voltage difference across any resistor can be found by subtracting node voltages, and this voltage difference is essential for calculating branch currents and power. Node voltages are always measured with respect to the reference node, and dependent sources must be handled carefully as they introduce additional constraints into the equations.
🧠 Quick Revision Questions
- What is the KCL equation for node A in the circuit with -12mA, +4mA, and I?
- For the circuit calculating I₁ and I₂, what value of I₁ is obtained from the node A equation?
- In the example finding I₀, what are the final values of V₁ and V₂ after solving the nodal equations?
- What value of V₂ makes V₁ = 0 in the example with the dependent source?
- What two node voltages Vₓ and Vᵧ are found when analyzing the circuit with the 6Ω resistor, and what power is absorbed by that resistor?
📘 Lecture 9 — Application of Nodal Analysis
📖 Overview: This lecture demonstrates the application of nodal analysis to solve complex circuit problems involving multiple nodes, voltage sources, and current sources. It reinforces the practical technique of setting up and solving simultaneous equations to determine unknown voltages and currents, which is fundamental for circuit analysis.
🗂️ Topics Covered
This lecture presents a series of seven detailed examples that apply nodal analysis to find unknown currents and voltages in various circuits. The examples progress from simple two-node circuits to more complex four-node circuits, including cases with dependent sources and circuits where voltage divider rule is applied after nodal analysis. Problems cover finding current through specific resistors, voltage across resistors, and the value of a dependent source constant.
📝 Lecture Summary
Example 1: Find current flowing through 6k ohm resistor
The circuit has two unknown nodes, node 1 and node 2. Apply Kirchhoff’s Current Law (KCL) at each node to establish equations.
At node 1: ((V1 - V2)/6k) + (V1/3k) = 2mA. This simplifies to V1 – V2 + 2V1 = 6k x 2mA → -V2 + 3V1 = 12. Multiply both sides by 3: 9V1 - 3V2 = 36. This is equation (A).
At node 2: V2/12k + 4mA + (V2 - V1)/6k = 0. This simplifies to V2 + 48 + 2V2 - 2V1 = 0 → 3V2 – 2V1 = -48. This is equation (B).
Add equations (A) and (B): (9V1 - 3V2) + (3V2 – 2V1) = 36 + (-48) → 7V1 = -12 → V1 = -12/7 V.
Substitute V1 into equation (A): V2 = 3V1 - 12 = 3(-12/7) - 12 = (-36/7) - 12 = (-36-84)/7 = V2 = -120/7 V.
The voltage across the 6k resistor is Vo = V2 – V1 = (-120/7) + (12/7) = -108/7 V. The current Io = Vo/6k = (-108/7) x (1/6k) = -108/42 = Io = -2.57 mA.
📌 Example: For the circuit with a 6k resistor between two nodes, V1 = -12/7 V, V2 = -120/7 V, and the current through the 6k resistor is 2.57 mA (flowing opposite to assumed direction).
Example 2: Find voltage across 2k ohm resistor
Combine the two series 2k resistors on the right side into a single 4k resistor. Then apply KCL at node 1 and node 2.
At node 1: V1/3k + 4mA + 2mA + (V1 - V2)/6k = 0. Multiply by 6k: 2V1 + 24 + 12 + V1 – V2 = 0 → 3V1 – V2 = -36.
At node 2: V2/4k + V2/12k - 2mA + (V2 – V1)/6k = 0. Multiply by 12k: 3V2 + V2 – 24 + 2V2 – 2V1 = 0 → 6V2 – 2V1 = 24.
Solve the two equations: from node 1 equation, -V2 + 3V1 = -36. Multiply by 2: -2V2 + 6V1 = -72. Add to node 2 equation (6V2 – 2V1 = 24): 4V2 = -48 → V2 = 0 V.
The voltage across the 2k resistor (using voltage divider rule on the series combination): V0 = (2/(2+2)) x V2 = 2/4 x 0 = 0 V.
🔑 Definition — Voltage Divider Rule: For two resistors in series, the voltage across one resistor equals the ratio of that resistor to the total resistance times the total voltage across the series combination. Formula: V_Rx = (Rx / (R1 + R2)) × V_total.
📌 Example: Two 2k resistors in series with 0V across them produce 0V across each resistor.
Example 3: Find current flowing through 4k ohm resistor
The circuit has a single unknown node V1. Apply KCL at node 1.
At node 1: (V1 - 12)/12k + V1/6k + (V1 + 6)/4k = 0. Multiply by 12k: V1 – 12 + 3V1 + 3(6) + 2V1 = 0 → 6V1 = -6 → V1 = -1 V.
The current through the 4k resistor: Io = (V1 – (-6))/4k. Note the negative sign is due to the negative reference of the battery. Io = (-1 + 6)/4k = 5/4k = Io = 1.2 mA.
📌 Example: For the circuit with a 12V battery and a -6V battery, V1 = -1V and the current through the 4k resistor connected to the -6V source is 1.2 mA.
Example 4: Find voltage across 1k ohm resistor
The 2k and 1k resistors are in series, so combine them into a single 3k resistor. Apply KCL at the single unknown node V1.
At node 1: (V1 + 6)/6k + (V1 + 3)/2k + V1/3k = 0. Multiply by 6k: 6 + V1 + 9 + 2V1 + 3V1 = 0 → 6V1 + 15 = 0 → V1 = -15/6 = -2.5 V.
Using the voltage divider rule on the original 2k and 1k series combination: V0 = (1k/(2k+1k)) x V1 = 1/3 x (-15/6) = V0 = -5/6 V ≈ -0.833 V.
📌 Example: The voltage across the 1k resistor in a series combination with a 2k resistor is -5/6 V when the node voltage is -15/6 V.
Example 5: Find the voltage across a 12K ohm resistance
This circuit has three nodes: reference, node between 6V battery and 12K resistance (neglected), and node V1. The node equation is written for V1.
At node 1: (V1 – 12)/6k + (V1 - 6)/12k + V1/6k = 0. Multiply by 12k: 2(V1 - 12) + (V1 - 6) + 2V1 = 0 → 2V1 - 24 + V1 - 6 + 2V1 = 0 → 5V1 = 30 → V1 = 6 V.
The voltage across the 12K resistor is between the 6V battery (Vs) and V1: V0 = V1 - Vs = V1 - 6 = 6 - 6 = 0 V.
📌 Example: When V1 equals the battery voltage (6V), the voltage across the 12K resistor connected between them is 0V.
Example 6: Find the current Io through the 12K ohm resistor
This circuit has two unknown nodes, V1 and V2. Apply KCL at both nodes.
At node 1: (V1+6)/12 + V1/12 + (V1 – V2)/12 = 0. Multiply by 12: V1 + 6 + V1 + V1 – V2 = 0 → 3V1 – V2 = -6. Multiply by 2: 6V1 – 2V2 = -12 (Equation A1).
At node 2 (both resistors are 12k, so resistances are in kΩ): (V2 – V1)/12 + V2/12 = 2mA. Multiply by 12: V2 – V1 + V2 = 24 → 2V2 – V1 = 24 (Equation B).
Add equation A1 and B: (6V1 – 2V2) + (2V2 – V1) = -12 + 24 → 5V1 = 12 → V1 = 12/5 = 2.4 V.
Substitute into equation A: V2 = 3V1 + 6 = 3(12/5) + 6 = (36 + 30)/5 = V2 = 66/5 = 13.2 V.
The current through the 12K resistor: Io = (V1 – V2)/12 = (12/5 – 66/5)/12 = (-54/5) x (1/12) = -54/60 = Io = -0.9 mA.
📌 Example: For the circuit with nodes at 2.4V and 13.2V, the current through the 12K resistor connecting them is 0.9 mA flowing from node 2 to node 1.
Example 7: Use nodal analysis to find Vp
The bottom node has the largest number of branch connections, so it is chosen as the reference node. Working from left to right, name nodes 1, P, 2, and 3.
At node 1: 10 = V1/20 + (V1 - Vp)/40. Multiply by 40: 400 = 2V1 + V1 - Vp → 3V1 – Vp = 400. Multiply by 20: 60V1 - 20Vp = 8000 [1].
At node P: 0 = (Vp - V1)/40 + Vp/100 + (Vp - V2)/50. Multiply by 200: 0 = 5(Vp - V1) + 2Vp + 4(Vp - V2) → 0 = 5Vp - 5V1 + 2Vp + 4Vp - 4V2 → -5V1 + 11Vp - 4V2 = 0. Multiply by 10: -50V1 + 110Vp - 40V2 = 0 [2].
At node 2: -2.5 + 2 = (V2 - Vp)/50 + (V2 - V3)/10. Simplify: -0.5 = (V2 - Vp)/50 + (V2 - V3)/10. Multiply by 50: -25 = (V2 - Vp) + 5(V2 - V3) → -25 = V2 - Vp + 5V2 - 5V3 → -Vp + 6V2 - 5V3 = -25 [3].
At node 3: 5 - 2 = V3/200 + (V3 - V2)/10. Simplify: 3 = V3/200 + (V3 - V2)/10. Multiply by 200: 600 = V3 + 20(V3 - V2) → 600 = V3 + 20V3 - 20V2 → -20V2 + 21V3 = 600. Multiply by 10: -200V2 + 210V3 = 6000 [4].
Solving the system of equations: Vp = 171.6 V.
💡 Why this matters: This example demonstrates that nodal analysis can handle circuits with four unknown nodes, requiring the solution of four simultaneous equations—a common real-world circuit analysis scenario.
📌 Example: In a complex circuit with four nodes, nodal analysis yields Vp = 171.6V after solving a system of linear equations.
Example 8: Use nodal analysis to find K that will cause Vy to be zero
This circuit has a dependent voltage source with gain K. Apply KCL at nodes x and y.
At node x: Vx/4 + (Vx - Vy)/2 + (Vx - 6)/1 = 0. Multiply by 4: Vx + 2(Vx - Vy) + 4(Vx - 6) = 0 → Vx + 2Vx - 2Vy + 4Vx - 24 = 0 → 7Vx - 2Vy = 24. With Vy = 0: 7Vx = 24 → Vx = 48/14 = 3.429 V (Equation [1] simplified).
At node y: (Vy - KVx)/3 + (Vy - Vx)/2 = 2. Multiply by 6: 2(Vy - KVx) + 3(Vy - Vx) = 12 → 2Vy - 2KVx + 3Vy - 3Vx = 12 → -2KVx - 3Vx + 5Vy = 12. With Vy = 0: -2KVx - 3Vx = 12.
From equation [2]: -2KVx - 3Vx = 12 → -2K(3.429) - 3(3.429) = 12 → -6.858K - 10.287 = 12 → -6.858K = 22.287 → K = -3.250.
📌 Example: For a dependent source with gain K, setting Vy = 0 requires K = -3.25, with Vx = 3.429V.
Example 9: Use nodal analysis to find I5
Choose the bottom node as ground. Name nodes: "1" (left-most), "2" (top), "3" (central), "4" (between 4Ω and 6Ω resistors).
At node 1: -3 = v1/2 + (v1 - v2)/1. Multiply by 2: -6 = v1 + 2(v1 - v2) → -6 = v1 + 2v1 - 2v2 → 3v1 - 2v2 = -6 [1].
At node 2: 2 = (v2 - v1)/1 + (v2 - v3)/3 + (v2 - v4)/4. Multiply by 12: 24 = 12(v2 - v1) + 4(v2 - v3) + 3(v2 - v4) → 24 = 12v2 - 12v1 + 4v2 - 4v3 + 3v2 - 3v4 → -12v1 + 19v2 - 4v3 - 3v4 = 24 [2].
At node 3: 3 = v3/5 + (v3 - v4)/7 + (v3 - v2)/3. Multiply by 105: 315 = 21v3 + 15(v3 - v4) + 35(v3 - v2) → 315 = 21v3 + 15v3 - 15v4 + 35v3 - 35v2 → -35v2 + 71v3 - 15v4 = 315 [3].
At node 4: 0 = v4/6 + (v4 - v3)/7 + (v4 - v2)/4. Multiply by 84: 0 = 14v4 + 12(v4 - v3) + 21(v4 - v2) → 0 = 14v4 + 12v4 - 12v3 + 21v4 - 21v2 → -21v2 - 12v3 + 47v4 = 0. Multiply by 2: -42v2 - 24v3 + 94v4 = 0 [4].
Solving the system of four equations: v3 = 6.76 V. Therefore, I5 = v3/5 = 1.352 A.
📌 Example: In a complex four-node circuit, solving the system yields v3 = 6.76V and the current through the 5Ω resistor (I5) is 1.352A.
⭐ Key Takeaways
Nodal analysis is a systematic method for determining unknown voltages by applying KCL at each non-reference node and solving the resulting system of linear equations. The number of equations equals the number of unknown node voltages. When resistors are in series, they can be combined to simplify the circuit before analysis. The voltage divider rule is a useful tool after nodal voltages are found to determine voltages across individual series resistors. Circuits with dependent sources require additional constraint equations but follow the same nodal analysis procedure.
🧠 Quick Revision Questions
- What is the first step in applying nodal analysis to a circuit?
- In Example 1, how many equations were needed to solve for two unknown node voltages?
- How does the voltage divider rule work for two resistors in series?
- In Example 8, what constraint was imposed to find the value of K?
- What is the formula for calculating current through a resistor between two nodes using nodal voltages?
📘 Lecture 10 — (Super Node - Constraint or Coupling Equation)
📖 Overview: This lecture introduces the concept of the super node, a powerful technique for analyzing circuits containing voltage sources between two non-reference nodes. It explains how to formulate constraint (or coupling) equations to mathematically describe super nodes, enabling the calculation of node voltages and currents in complex circuits. This topic is crucial for simplifying circuit analysis where standard nodal analysis would be difficult.
🗂️ Topics Covered
The lecture begins with examples calculating current through resistors using standard node voltage analysis, then introduces the super node concept as a combination of two ordinary nodes around a voltage source. It explains the constraint or coupling equation that mathematically describes a super node, and works through multiple examples calculating currents, voltages, and power in circuits with dependent and independent sources using this technique.
📝 Lecture Summary
Example: Calculate the current I₀ through the 3k ohm resistor.
Solution: At node A: ((V₁ – V₂)/3k) + (V₁/6k) = 2mA where V₂ = 6V
Substituting V₂: ((V₁ – 6)/3k) + (V₁/6k) = 2mA
Multiplying by 6k: 2V₁ - 12 + V₁ = 12 3V₁ = 24 V₁ = 8 volts
By Ohm's law: I₀ = (V₁ - V₂)/3k = (8 - 6)/3k = 0.667 mA
I₁ = 6/4k = 1.5 mA
Example: Calculate the current I₀ through the 10k ohm resistor also find V₁ and V₂.
Solution: I₀ = V₁/10k ----------------- (A)
For node 1: (V₁/10k) + ((V₁ - V₂)/10k) = 4mA (V₁/10k) + (V₁/10k) – (V₂/10k) = 4mA
Substituting I₀: I₀ + I₀ – (V₂/10k) = 4mA 2I₀ - (V₂/10k) = 4mA 20I₀ – V₂ = 40mA ------------- (B)
For node 2: (V₂/10k) + ((V₂ – V₁)/10k) = -2I₀ (V₂/10k) + (V₂/10k) – (V₁/10k) = -2I₀ (V₂/10k) + (V₂/10k) – I₀ = -2I₀
Equating equations of node 1 and 2: 2V₂ + 10I₀ = 0 ---------------- (C)
Solving (B) and (C): 50I₀ = 80mA Hence I₀ = 8/5 mA
From equation (A): I₀ = V₁/10k 8/5 mA = V₁/10k V₁ = 16 volts
Substituting I₀ from (A) into (C): 2V₂ + V₁ = 0 2V₂ = -V₁ V₂ = -16/2 = -8 volts
SUPER NODE:
A super node is a node which emerges as a result of combination of two ordinary nodes around a voltage source.
CONSTRAINT OR COUPLING EQUATION:
This is an equation which describes a super node mathematically, instead of writing equations for individual ordinary nodes of the super node.
Example: Calculate the power supplied by the current source.
Solution: Power = 1A(V₁)
Applying KCL to node 1: (V₁/10) - Iₓ = 1
Applying KCL to node 2: 0 = Iₓ + (V₂/5) + ((V₂-2)/7)
Now, 3 unknown quantities cannot be calculated from 2 equations, so try super node technique.
Equation for super node: 1 = (V₁/10) + (V₂/5) + ((V₂-2)/7)
Simplifying: 35V₁ + 120V₂ = 450 --------- (A)
Constraint or coupling equation: V₁ - V₂ = 6
Solving the two equations simultaneously: V₂ = V₁ – 6
Substituting into (A): 35V₁ + 120(V₁ – 6) = 450 35V₁ + 120V₁ – 720 = 450 155V₁ = 1170 V₁ = 7.55V
Therefore: V₁ = 7.55 V and V₂ = 1.55 V
Hence, power: P = 1(A)(V₁) = 7.55 W
Example: Calculate I₁ from the given circuit.
Solution: Redrawing the circuit:
Constraint equation for super node: V₁ – V₂ = 3
KCL equation for super node: (V₁/3k) + (V₂/6k) = 2 × 10⁻³ 2V₁ + V₂ = 12
From constraint equation: V₂ = V₁ - 3
Substituting into KCL equation: 2V₁ + V₁ – 3 = 12 3V₁ = 15 V₁ = 5 volts
Now: I₁ = V₁/3k = 5/3k = 1.6 mA
Example: Find I₁ from the circuit.
Solution: Redrawing the circuit:
Constraint equation for super node: V₂ – V₁ = 6V
KCL equation for super node: ((V₁ – 3)/6k) + (V₁/12k) + ((V₂ + 3)/12k) + (V₂/12k) = 0
2V₁ - 6 + V₁ + V₂ + 3 + 2V₂ = 0 3V₁ + 3V₂ = 3 V₂ + V₁ = 1
Adding constraint equation and KCL equation: V₂ – V₁ = 6 V₂ + V₁ = 1
2V₂ = 7 V₂ = 3.5V
I₁ = 3.5/6k = 35/60k = 7/12 mA
Example: Calculate the value I₁.
Solution: For node 1: (V₁/12k) + (V₁/4k) + (V₁/6k) – (6/6k) = 2 mA
((1/12k) + (1/4k) + (1/6k))V₁ – (6/6k) = 2 mA
(V₁/2k) – (1/1k) = 2 × 10⁻³ V₁ – 2 = 4 V₁ = 6V
I₁ = V₁/4k = 6/4k = 1.5 mA
⭐ Key Takeaways
The super node technique is essential when a voltage source connects two non-reference nodes in a circuit. Instead of writing separate KCL equations for each node, you combine them into one super node equation and add a constraint (coupling) equation that expresses the voltage difference between the two nodes (V₁ - V₂ = source voltage). This approach reduces the number of unknowns and simplifies the analysis. Always identify the super node around voltage sources between non-reference nodes, write the KCL equation for the entire super node, and then add the constraint equation based on the voltage source value. The sign convention in the constraint equation must match the polarity of the voltage source.
🧠 Quick Revision Questions
- What is a super node, and when do you use it in circuit analysis?
- Write the general form of a constraint or coupling equation for a super node containing a voltage source of value Vₛ.
- In the example with the 10k ohm resistor, why was the super node technique not needed, and how were V₁ and V₂ found?
- For the circuit with power supplied by the current source, how many equations were needed and what were they?
- If a super node has two ordinary nodes with a 6V source between them and the KCL equation gives V₂ + V₁ = 1, what are the values of V₁ and V₂?
📘 Lecture 11 — Examples of Nodal Analysis - Super Node technique
📖 Overview: This lecture demonstrates the application of nodal analysis and the super node technique through multiple worked examples. It shows how to handle circuits containing voltage sources between nodes by forming a super node and solving for unknown voltages and currents.
🗂️ Topics Covered
The lecture covers five complete examples of nodal analysis: finding output voltage using constraint equations, calculating voltage and current using super node analysis, applying voltage division with super node results, solving circuits with dependent current sources, and determining current direction through negative sign interpretation.
📝 Lecture Summary
Example: Find the output voltage V₀
The circuit contains a voltage source between nodes. By redrawing the circuit, V₁ is identified as 6V. The constraint equation is V₁ – V₃ = 3V.
🔑 Definition — Constraint Equation: An equation that expresses the voltage relationship between two nodes due to a voltage source connected between them.
📐 Formula: V₁ – V₃ = 3V → The voltage across the source equals the difference between the two node voltages.
📌 Example: Given V₁ = 6V, the constraint equation 6 – V₃ = 3V gives V₃ = 3V. Since V₃ = V₀, therefore V₀ = 3 Volts.
Example: Calculate V₀ and I₀
Node 2 and Node 3 form a super node because a 6V voltage source is connected between them.
🔑 Definition — Super Node: A technique used when a voltage source is connected between two non-reference nodes. The two nodes are combined into one "super node" for KCL analysis.
📐 Constraint Equation: V₂ – V₃ = 6 --------------------- (A)
📐 KCL at Super Node: Sum of all currents leaving the super node = 0
📌 Example: KCL: (V₂-12)/6k + (V₂/3k) + (V₃/6k) + (V₃-12)/12k = 0 Simplifies to: 2V₂ + V₃ = 12 ......(B)
From constraint (A): V₃ = V₂ – 6 Substitute into (B): 2V₂ + (V₂ – 6) = 12 3V₂ = 18 → V₂ = 6 Volts Therefore V₃ = 0 Volt
V₀ = 0 Volt I₀ = V₂/3k = 6/3k = 2mA
Example: Calculate the value of V₀
The circuit contains a 6V voltage source between Node 2 and Node 3, forming a super node.
📐 Constraint Equation: V₃ – V₂ = 6 volts
📌 Example: KCL at super node: (V₂ – 6)/6k + V₂/12k + (V₃-6)/4k + V₃/12k + V₃/6k = 0 Simplifies to: V₂ + 2V₃ = 10 ----- (A)
From constraint: V₂ = V₃ – 6 Substitute into (A): (V₃ – 6) + 2V₃ = 10 → 3V₃ = 16 V₃ = 16/3 volts V₂ = (16/3) – 6 = –2/3 V
💡 Why this matters: These node voltages allow us to find V₀ using voltage division.
Voltage Division Rule: V₀ = (4k × V₃)/(2k + 4k) = 64/18 = 3.55 Volts
Example: Find V₀ (Circuit with Dependent Source)
This circuit has a dependent current source 2Iₓ controlled by current Iₓ.
📌 Example: At Node 1: V₁/10k = 3mA – 2Iₓ Given Iₓ = V₁/10k, substitute: V₁/10k = Iₓ = 3mA – 2Iₓ → 3Iₓ = 3mA → Iₓ = 1mA
At Node 2: V₂/10k = 2Iₓ = 2(1mA) → V₂ = 20 Volts Therefore V₀ = 20 Volts
Example: Find I₀
A straightforward nodal analysis problem without super nodes.
📌 Example: KCL at Node 1: (V₁ – 6)/4k + V₁/10k + (V₁ – 12)/2k = 0 Multiply through: 5V₁ – 30 + 2V₁ + 10V₁ – 120 = 0 17V₁ = 150 → V₁ = 8.82 Volts
I₀ = (V₁ – 12)/2k = (8.82 – 12)/2k = –1.58 mA
💡 Why this matters: The negative sign indicates the actual current flows in the opposite direction to what was assumed in the circuit diagram.
⭐ Key Takeaways
The super node technique is essential when a voltage source connects two non-reference nodes — these nodes are combined and their constraint equation is written as V₂ – V₃ = source voltage. When writing the KCL equation at the super node, sum all currents leaving the combined super node region, treating internal connections as part of the super node. Always substitute the constraint equation into the KCL equation to solve for node voltages. For circuits with dependent sources, express the controlling variable in terms of node voltages and solve the system of equations. A negative current result indicates the actual current direction is opposite to the assumed direction in the circuit diagram.
🧠 Quick Revision Questions
- What is a super node and when is it used in nodal analysis?
- In the super node technique, what form does the constraint equation take when a 6V source connects Node 2 and Node 3?
- If V₂ = 6V and the constraint equation is V₂ – V₃ = 6V, what is the value of V₃?
- How is voltage division rule applied to find V₀ from node voltages and resistor values?
- What does a negative current value like –1.58mA indicate about current direction?
📘 Lecture 12 — (Kirchhoff's Voltage Law (KVL) - Loop - Examples)
📖 Overview: This lecture introduces Kirchhoff's Voltage Law (KVL), a fundamental principle in circuit theory that governs voltage relationships in closed loops. It explains how to write KVL equations, the assumptions involved, and demonstrates the application through worked examples.
🗂️ Topics Covered
The lecture covers the statement and meaning of Kirchhoff's Voltage Law, the definition of a loop, the assumptions for sign conventions (energy level increases and decreases, current direction relative to source), and the rule for the number of equations needed. Detailed step-by-step examples show how to write KVL equations for circuits with multiple loops and voltage sources, and demonstrates the concept of linear dependence among loop equations.
📝 Lecture Summary
KIRCHHOFF’S VOLTAGE LAW:
This law states that the algebraic sum of the voltages around any loop is zero. OR Sum of voltages rises and voltage drops around any closed path or loop is equal to zero.
LOOP:
It is the closed path for the flow of current in which no node is encountered more than once. Loop can be considered as closed path in which work done in moving a unit charge is equal to zero.
ASSUMPTIONS:
Any increase in energy level is taken as positive and any decrease in energy level is taken as negative. Current leaving the source is taken as positive and current entering the voltage source is taken as negative.
NO. OF EQUATIONS:
No. of equations to be written are equal to the no. of loops or closed paths.
Example:
We want to calculate the value of VR₃ where values of VR₁ and VR₂ are known by using KVL.
Solution: Now we will take increase in energy level positive and decrease in energy level negative. By using this assumption and KVL the equation of this loop will be:
+VR₁ - 5 + VR₂ – 15 + VR₃ – 30 = 0
which can be written as: VR₁ + VR₂ + VR₃ = 5 + 15 + 30 = 50
Now suppose that VR₁ and VR₂ are known to be 18V and 12V respectively:
VR₃ = 50 - 18 – 12 = 20V
🔑 Definition — Loop: The closed path for the flow of current in which no node is encountered more than once. It is a closed path in which work done in moving a unit charge is equal to zero.
📐 Formula: KVL: Sum of voltage rises = Sum of voltage drops, or ΣV = 0 around any closed loop.
📌 Example: In a loop with voltage sources 5V, 15V, 30V and resistors with voltage drops VR₁=18V, VR₂=12V, VR₃ unknown: The KVL equation gives VR₁ + VR₂ + VR₃ = 5 + 15 + 30 = 50, so VR₃ = 50 – 18 – 12 = 20V.
💡 Why this matters: This example shows how KVL provides a simple algebraic method to find an unknown voltage when other voltages in the loop are known.
Example:
Note that this network has three closed paths: the left loop, the right loop and outer loop.
Applying KVL to left loop: VR₁ + VR₄ – 16 – 24 = 0
KVL equation for right loop starting at point B: VR₂ + VR₃ + 8 + 16 – VR₄ = 0
The equation for outer loop starting at point A: VR₁ + VR₂ + VR₃ + 8 – 24 = 0
Note that if we add first two equations, we obtain the third equation. So these three equations are not linearly independent. We will discuss this issue in next lectures that we will use only linearly independent equations to solve for all voltages.
📌 Example: A circuit has three closed paths (left loop, right loop, and outer loop). Writing KVL for each:
- Left loop: VR₁ + VR₄ – 16 – 24 = 0
- Right loop (starting at B): VR₂ + VR₃ + 8 + 16 – VR₄ = 0
- Outer loop (starting at A): VR₁ + VR₂ + VR₃ + 8 – 24 = 0
Adding the left and right loop equations gives the outer loop equation, showing they are not all independent.
💡 Why this matters: This example demonstrates that not all loop equations are independent; some are linear combinations of others. For solving circuits, we need to select only the linearly independent equations.
⭐ Key Takeaways
Kirchhoff's Voltage Law states that the algebraic sum of voltages around any closed loop equals zero, meaning the sum of voltage rises equals the sum of voltage drops. In writing KVL equations, increases in energy level are taken as positive and decreases as negative; current leaving the source is positive and entering is negative. The number of KVL equations to write equals the number of loops in the circuit. However, not all loop equations are linearly independent — some may be derived from adding others, so only independent equations should be used for solving circuit unknowns.
🧠 Quick Revision Questions
- State Kirchhoff's Voltage Law in your own words.
- What is the sign convention for energy level changes when applying KVL?
- How is current direction treated relative to a voltage source in KVL sign conventions?
- In a circuit with three possible loops, how many independent KVL equations would you expect?
- If the left loop equation is VR₁ + VR₄ = 40 and the right loop equation is VR₂ + VR₃ – VR₄ + 24 = 0, what would be the outer loop equation?