📘 Lecture 1 — Introduction-Some Basic Concepts
📖 Overview: This lecture introduces the fundamental building blocks of circuit theory, beginning with the International System of Units (SI) and its seven base units. It then explores the atomic structure of matter, explaining how electrons, protons, and neutrons form atoms, and how the behavior of electrons determines whether a material is a conductor, insulator, or semiconductor. Finally, it establishes the core electrical concepts of current, voltage, resistance, and power, along with their units and the fundamental relationship defined by Ohm's Law.
🗂️ Topics Covered
The lecture begins with a detailed look at the seven base SI units (meter, kilogram, second, ampere, Kelvin, mole, candela), their definitions, and the decimal prefixes used to scale them. It then delves into subatomic particles (electrons, protons, neutrons) and the structure of the atom, including electron shells, valence, and atomic number. Following this, the concepts of conductors, insulators, and semiconductors are introduced. The lecture then formally defines the coulomb as the unit of electric charge and explains static electricity and charge polarity. Finally, it covers the fundamental principles of electricity in a circuit: the nature of electric current, the role of a battery, and the key measurements of current (in amperes), voltage (in volts), and resistance (in ohms), culminating in Ohm's Law and the Power Formula.
📝 Lecture Summary
International System of Units
The International System of Units (SI) is built upon seven basic units: meter (length), kilogram (mass), second (time), ampere (electric current), Kelvin (thermodynamic temperature), mole (amount of substance), and candela (luminous intensity). The meter is defined as the distance traveled by light in a vacuum in 1/299,792,458 of a second. The second is defined as the duration of 9,192,631,770 cycles of radiation from a specific transition of the Cesium-133 atom. The kilogram is the only base unit still defined by a physical object, a platinum-iridium cylinder. The Kelvin is defined as 1/273.16 of the thermodynamic temperature of the triple point of water, which is 0.01°C or 32.02°F; 0°K is called absolute zero. The ampere is defined as the constant current that, if maintained in two long parallel wires one meter apart, would produce a force of 2 x 10⁻⁷ newtons per meter between them.
🔑 Definition — Joule: The energy consumed in moving an object of one kilogram through a distance of one meter. One joule is equivalent to 0.7376 foot pound-force and 0.2388 calories.
🔑 Definition — Watt: The rate of doing work. One watt equals one joule per second (1 W = 1 J/s) and is equivalent to 0.7376 ft-lbf/s or 1/745.7 horsepower.
The SI system uses a decimal system with prefixes to signify powers of 10. Examples include milli (m, 10⁻³), micro (µ, 10⁻⁶), nano (n, 10⁻⁹), pico (p, 10⁻¹²), kilo (k, 10³), mega (M, 10⁶), and giga (G, 10⁹).
📌 Example 1: A laser emits light at a wavelength of 248 nm. This is the same as: (a) 0.0248 millimeter (b) 2.48 micrometer (c) 0.248 micrometer () (d) 24800 angstrom
📌 Example 2: A logic gate switches from on to off in 10 nanoseconds. This corresponds to: (a) 0.1 microsecond (b) 10 microseconds (c) 0.001 microsecond () (d) 0.01 microsecond
Sub-atomic Elements and the Atom
The three stable particles in an atom are the electron (negatively charged), the proton (positively charged), and the neutron (neutral, no charge). An atom is the smallest particle of an element. Protons and neutrons are in the nucleus, while electrons orbit in shells. The electrical force attracting the electron to the proton is balanced by the mechanical (centrifugal) force directing it outwards. In a neutral atom, the number of electrons equals the number of protons. The distribution of electrons in orbital rings determines the atom's electrical stability.
🔑 Definition — Free Electrons: The outermost electrons in a material like copper, which are not tightly bound to any one atom and can migrate easily from one atom to another at random.
The modern planetary model of the atom was proposed by Niels Bohr in 1913, incorporating the nuclear atom by Lord Rutherford and the quantum theory by Max Planck and Albert Einstein. The orbits for planetary electrons are also called shells or energy levels.
🔑 Definition — Electron Valence: The number of electrons in an incomplete outermost shell. A completed outer shell has a valence of zero. Copper has a valence of 1.
All shells except the K shell are divided into sub-shells, which account for different types of orbits (e.g., circular vs. elliptical) and the magnetic properties of the atom.
🔑 Definition — Atomic Number: The number of protons (or electrons in a neutral atom) in an atom of an element. For example, a hydrogen atom has an atomic number of 1.
The planetary electron shells are called K, L, M, N, O, P, and Q at increasing distances from the nucleus. Each shell has a maximum number of electrons for stability, corresponding to the inert gases (e.g., K=2 for Helium, L=8 for Neon). The electronic configuration for copper (29 protons) is K=2, L=8, M=18, N=1.
📌 Example 1: An element with 16 protons and 16 electrons has atomic number: (c) 16
📌 Example 2: The electron valence of an element with atomic number 5 (electronic config: K=2, L=3) is: (b) 3
Conductors, Insulators, and Semiconductors
A conductor is a material where electrons can move easily from one atom to another. All metals are good conductors. An insulator (or dielectric) is a material where electrons tend to stay in their own orbits and cannot conduct electricity easily. A semiconductor (e.g., carbon, germanium, silicon) conducts less than a conductor but more than an insulator.
Coulomb: The Unit of Electric Charge
The fundamental unit of electric charge is the coulomb (C). One coulomb equals the charge of 6.25 × 10¹⁸ electrons or protons. The analysis of static charges and their forces is called electrostatics. The symbol for electric charge is Q or q. Negative polarity refers to the static charge on rubber and resin, while positive polarity refers to the charge on glass. The law of electrical charges states: Like charges repel, opposite charges attract.
The Atom (Advanced)
An ion is an atom that has gained or lost electrons, giving it a net positive or negative charge. Isotopes are atoms of the same element (same atomic number) but with different numbers of neutrons. The designations of positive and negative were made by Benjamin Franklin.
What is Electricity?
Electricity is the flow of free electrons in a wire, a flow called current. Electrons flow because they are attracted to a positive charge and repelled by a negative charge at opposite ends of a wire.
Batteries
A battery is a device that creates a positive charge at one terminal and a negative charge at the other, causing a current to flow. When a closed circuit is formed by connecting a wire across the terminals, electrons flow from the negative terminal to the positive terminal. However, by convention, current is said to flow from positive to negative.
Measuring Current
Current (I) is measured in amperes (A). One ampere is defined as 1 coulomb per second (1 A = 1 C/s).
Measuring Voltage
Voltage (V) is a measure of the "electrical pressure" pushing electrons through a wire. It is measured in volts (V). A voltage of 1 volt means the battery delivers 1 joule of energy for each coulomb of charge that flows.
Measuring Resistance
Resistance (R) is a measure of how much a wire impedes the flow of current. It is measured in ohms (Ω). A resistor is a circuit component that provides a specific amount of resistance.
🔑 Definition — Ohm's Law: The relationship between voltage (V), current (I), and resistance (R). The formula is: 📐 Formula: I = V / R → Current equals voltage divided by resistance. 📌 Example: If a 2-volt battery is connected to a 3-ohm resistor, the current is I = 2 V / 3 Ω = 2/3 amperes.
Measuring Power in Watts
Power (P) is the rate at which energy is delivered or consumed. It is measured in watts (W), where 1 watt equals 1 joule per second (1 W = 1 J/s).
📐 Formula: P = I × V → Power equals current times voltage. 📌 Example: With a battery voltage of 2 volts and a current of 3 amps, the power delivered to the resistor is P = 3 A × 2 V = 6 watts.
⭐ Key Takeaways
This lecture establishes the absolute foundation for circuit theory. You must be fluent in the definitions and symbols for the three fundamental circuit quantities: voltage (V, in volts), current (I, in amperes), and resistance (R, in ohms). The core relationship linking them is Ohm's Law (I = V/R), which you will use constantly. The concept of power (P = I×V, in watts) is equally critical, as it describes energy transfer. Finally, understanding the atomic basis for conductors (like copper with free electrons), insulators, and semiconductors is essential for grasping why materials behave as they do in circuits. Remember the conventional current direction (positive to negative) even though electron flow is opposite.
🧠 Quick Revision Questions
- What is the difference between the flow of electrons and the direction of conventional current in a circuit?
- State Ohm's Law in words and as a formula. If you know the voltage and current in a circuit, how would you calculate the resistance?
- Define a "coulomb." How many electrons does it contain?
- What is the electron valence of an atom, and why is it important for determining if a material is a conductor?
- If a 9-volt battery delivers a current of 2 amperes to a light bulb, what is the power consumed by the bulb and the resistance of the bulb?
📘 Lecture 2 — Introduction-some basic concepts
📖 Overview: This lecture introduces fundamental electrical concepts including battery polarities, potential difference, voltage, current, resistance, and power. It explains the relationship between these basic quantities and their practical significance in circuit analysis, making it essential foundational knowledge for all subsequent circuit theory topics.
🗂️ Topics Covered
The lecture covers negative and positive polarities of battery, potential difference and its calculation between different charges, voltage conventions and the volt unit, current definition and mathematical expression (I = dq/dt), the ampere unit, resistance and conductance concepts, ohm unit, closed/open/short circuits, power (P = V×I), passive sign conventions, and the importance of earth ground versus chassis ground with safety implications.
📝 Lecture Summary
NEGATIVE AND POSITIVE POLARITIES OF BATTERY
All materials contain two basic particles of electric charge: electrons (negative polarity) and protons (positive polarity). To use electrical forces associated with these charges, work must be done to separate electrons and protons. A battery uses chemical energy to separate electric charges, producing an excess of negative charge at its negative terminal and an excess of positive charge at its positive terminal. With separate and opposite charges at the two terminals, electric energy can be supplied to a circuit connected to the battery.
POTENTIAL DIFFERENCE
Potential difference is the difference between electric potentials at two terminals of a circuit element. Potential refers to the possibility of doing work. Any charge has the potential to do work of moving another charge by attraction or repulsion. When we consider two unlike charges, they have a difference of potential. A charge results from work done in separating electrons and protons. The work of producing charge causes a condition of stress in protons, which try to attract electrons and return to the neutral condition.
POTENTIAL BETWEEN DIFFERENT CHARGES
For a positive charge of 3 C, work must be done to move electrons. Assuming a charge of 1C can move three electrons: a +3C charge can attract 9 electrons toward right, while a +1C charge can attract 3 electrons toward left. The net result is that 6 electrons move toward the more positive charge. When one charge is 2C and the other is neutral (0C), for the difference of 2C, 6 electrons can be attracted to the positive side.
🔑 Definition — Potential Difference: The difference between electric potentials at two terminals of a circuit element.
POTENTIAL DIFFERENCE BETWEEN THE TERMINALS
A voltage can exist between the terminals of a battery whether current is flowing or not. An automobile battery, for example, has 12 volts across its terminals even if nothing is connected to the terminals.
VOLTAGE CONVENTIONS
The volt is named after Alessandro Volta. Fundamentally, the volt measures the work needed to move an electric charge. When 0.7376 foot-pound of work is required to move 6.25×10¹⁸ electrons between two points, the potential difference is one volt. 6.25×10¹⁸ electrons make up one coulomb. 0.7376 ft-lb of work equals 1 joule.
📐 Formula: 1V = 1J/1C → One volt equals one joule per coulomb (the work per unit charge).
The symbol of potential difference is V for voltage. The volt unit is used so often that potential difference is called voltage.
CURRENT
When the potential difference between two charges forces a third charge to move, the charge in motion is called current. To produce current, charge must be moved by a potential difference. In solid materials like copper wire, free electrons can be forced to move by a potential difference. This current is a drift of electrons, from the point of negative charge at one end to the positive charge at the other end. All electrons are identical; the drift of free electrons results in charge moving through the wire. Current is the constant flow of electrons. Only the electrons move, not the potential difference. The current must be the same at all points of the wire at all times.
Let q(t) be the total charge that has passed a reference point since time t=0, moving in the defined direction. The current at a specific point flowing in a specified direction is the instantaneous rate at which net positive charge is moving past that point.
📐 Formula: I = dq/dt → Current equals the time rate of change of charge (coulombs per second or amperes).
Current is symbolized as I or i.
POTENTIAL DIFFERENCE IS NECESSARY FOR CURRENT
The number of free electrons forced to drift through a wire depends upon the amount of potential difference across the wire. With more applied voltage, the forces of attraction and repulsion make more free electrons drift, producing more current. With zero potential difference across the wire, there will be no current.
THE AMPERE OF CURRENT
Since current is the movement of charge, the unit for stating the amount of current is defined as the rate of flow of charge.
🔑 Definition — Ampere: When charge moves at the rate of 6.25×10¹⁸ electrons flowing past a given point per second, the value of current is one Ampere.
RESISTANCE
The fact that a wire conducting current can become hot shows that work is done against some form of opposition. This opposition, which limits current, is called resistance. Copper wire has many free electrons that move easily, giving low resistance. Carbon has fewer free electrons than copper, so when the same voltage is applied, fewer electrons flow. Carbon opposes current more than copper, therefore having higher resistance.
🔑 Definition — Ohm: A resistance that develops 0.24 calorie of heat when one ampere of current flows through it for one second has opposition of one ohm.
The symbol for resistance is R. The abbreviation for ohm is the Greek letter OMEGA (Ω). In diagrams, resistance is indicated by a zigzag line.
CONDUCTANCE
The reciprocal of resistance is called conductance. The lower the resistance, the higher the conductance. Its symbol is G and the unit is siemens (formerly mho).
📐 Formula: G = 1/R → Conductance equals the reciprocal of resistance.
THE CLOSED CIRCUIT
For a closed circuit, three conditions must be met: (1) There must be a source of voltage; without applied voltage, current cannot flow. (2) There must be a complete path for current flow from one side of the voltage source, through the external circuit, returning to the other side. (3) The current path normally has resistance, either for generating heat or limiting current.
OPEN CIRCUIT
When any part of the path is broken, the circuit is open because there is no continuity in the conducting path. The resistance of an open circuit is infinitely high, resulting in no current.
SHORT CIRCUIT
In a short circuit, the voltage source has a closed path across its terminals, but the resistance is practically zero. The result is too much current. Usually, the short circuit is a bypass across the load resistance.
POWER
Rate of doing work is called power. The unit of electric power is watt. One watt equals the work done in one second by one volt moving one coulomb of charge. One coulomb per second is an ampere.
📐 Formula: P = V × I → Power in watts equals volts times amperes (joules per coulomb × coulombs per second = joules per second or watts).
If one terminal of an element is v volts positive with respect to the other, and current i enters the element through that terminal, then power p = vi is absorbed by the element.
PASSIVE SIGN CONVENTIONS: If the current arrow is directed into the + marked terminal of an element, then p = vi yields the absorbed power. A negative value indicates the power is actually being generated by the element.
📌 Example: A 12V lead-acid battery delivers total energy of 460.8 watt-hours over 8 hours.
(a) Power delivered = (460.8 W-hr) / (8 hr) = 57.6 W
(b) Current through headlight = Power / Voltage = (57.6 W) / (12V) = 4.8 A
Importance of Earth Ground
Voltage cannot be defined at a single point; it is by definition the difference in potential between two points. Many schematics use the convention of taking earth as defining zero volts, so all other voltages are implicitly referenced to this potential. This concept is called earth ground and is fundamentally tied to safety regulations to prevent fires, fatal electrical shocks, and related hazards.
The earth ground symbol represents a common node. Circuits using earth ground as a common terminal are equivalent in terms of voltage values.
Chassis Ground: The common terminal of every circuit in equipment may be tied together and electrically connected to the conducting equipment chassis. This terminal is often denoted using the chassis ground symbol. The electrical connection to earth may have nonzero resistance. The fact that "ground" is not always "earth ground" can cause serious safety and electrical noise problems. If a person's equivalent resistance is significantly less than the resistance of all other possible paths to ground, dangerous electric shock can occur.
⭐ Key Takeaways
Current (I = dq/dt) flows only when a potential difference exists across a conductor, with the ampere defined as 6.25×10¹⁸ electrons per second passing a point. Voltage (1V = 1J/1C) represents work per unit charge and exists even without current flow. Resistance opposes current flow, with conductance (G = 1/R) as its reciprocal in siemens. Power (P = V×I) follows passive sign convention where current entering the positive terminal indicates power absorption. Earth ground (zero volts reference) differs from chassis ground, and this distinction is critical for safety—improper grounding can create lethal shock hazards when low-resistance paths to ground exist through a person.
🧠 Quick Revision Questions
- What is the mathematical relationship between current and charge, and what is the unit of current?
- How is one volt defined in terms of work and charge?
- What is the difference between an open circuit and a short circuit?
- Using passive sign convention, when does p = vi represent power absorbed versus power generated?
- Why is it dangerous to assume that chassis ground is the same as earth ground?
📘 Lecture 3 — (Resistance in Series)
📖 Overview: This lecture introduces the fundamental concepts of series and parallel resistor connections and how to simplify complex resistor networks into a single equivalent resistance. Mastering these simplification techniques is crucial for analyzing any circuit, as they form the basis for calculating current, voltage, and power in more complex systems.
🗂️ Topics Covered
The lecture begins by defining resistors in series, where the end of one resistor connects to the start of another, and derives the formula for equivalent resistance as the sum of individual resistances. It then introduces resistors in parallel, where corresponding terminals are joined, and presents the reciprocal formula for calculating the equivalent resistance. The bulk of the lecture is dedicated to numerous worked examples that demonstrate the step-by-step process of simplifying circuits that combine both series and parallel resistors, progressively reducing them to a single equivalent resistor.
📝 Lecture Summary
Resistance in Series
If we connect resistors across a source such that the ending point of one resistor is joined with the starting point of the other resistor, then they are said to be connected in series. The combined effect of all the resistors will be equal to the sum of individual resistances.
Consider two resistances R1 and R2 with terminals A, B and C, D. They will be in series if we connect B with C. The combined effect of these two resistances will be: Req = R1 + R2
Therefore, if we connect N resistances in series then: R_eq = R1 + R2 + R3 + ... + RN
🔑 Definition — Series Connection: A configuration where components are connected end-to-end so that the same current flows through each component.
📐 Formula: R_eq = R1 + R2 + ... + RN → The total resistance of a series circuit is the arithmetic sum of all individual resistances.
📌 Example 1: Simplify the given circuit with two 1kΩ resistors in series. Solution: R_AB = R1 + R2 = 1k + 1k = 2kΩ
📌 Example 2: Simplify the given circuit. Solution: 1kΩ and 4kΩ are in series so they will be combined as 5kΩ. Now 5kΩ and 3kΩ are also in series, resulting in 8kΩ. 2kΩ and 8kΩ are also in series. So R_AB = 2k + 8k = 10kΩ
Resistance in Parallel
Consider two resistances with terminals A, B and C, D. If we connect A with C and B with D, they are said to be connected in parallel.
The equivalent of these two resistances will be: 1/R_eq = 1/R1 + 1/R2 = (R1 × R2) / (R1 + R2)
If we connect N number of resistances in parallel, their equivalent will be: 1/R_eq = 1/R1 + 1/R2 + 1/R3 + ... + 1/RN
🔑 Definition — Parallel Connection: A configuration where all components are connected across the same two points, providing multiple paths for current to flow.
📐 Formula: 1/R_eq = 1/R1 + 1/R2 + ... + 1/RN or R_eq = (R1 × R2)/(R1 + R2) for two resistors → The total resistance of a parallel circuit is less than the smallest individual resistance.
📌 Example 3: Simplify the given circuit with two 1kΩ resistors in parallel. Solution: R_eq = (R1 × R2)/(R1 + R2) = (1 × 1)/(1 + 1) = 1/2 = 0.5kΩ
📌 Example 4: Simplify the given circuit. Solution: 4kΩ is parallel with 4kΩ so 4k||4k = (4 × 4)/(4 + 4) = 16/8 = 2kΩ. 2kΩ is parallel with 2kΩ. So R_eq = (2 × 2)/(2 + 2) = 4/4 = 1kΩ
📌 Example 5: Simplify the given circuit. Solution: 12kΩ is parallel with 4kΩ so 12k||4k = (12 × 4)/(4 + 12) = 48/16 = 3kΩ. Now 2kΩ is in series with 3kΩ so R_AB = 2k + 3k = 5kΩ
📌 Example 6: Simplify the given circuit. Solution: 4kΩ is in series with 8kΩ so the combined effect = 12kΩ. 12kΩ is in parallel with 12kΩ so 12k||12k = (12 × 12)/(12+12) = 144/24 = 6kΩ. 4kΩ is in series with 6kΩ so their combined effect = 4k + 6k = 10kΩ. 6kΩ is in parallel with 10kΩ so R_AB = (6 × 10)/(6+10) = 3.75kΩ 💡 Why this matters: This example shows how circuits with multiple series and parallel combinations can be simplified step-by-step by repeatedly applying the two fundamental formulas.
📌 Example 7: Simplify the given circuit. Solution: 3kΩ is in series with 6kΩ, therefore, their combined effect = 3k + 6k = 9kΩ. 9kΩ is in parallel with 18kΩ so 9k||18k = (9 × 18)/(9+18) = 162/27 = 6kΩ. 6kΩ is in series with 10kΩ. So their combined effect = 6k + 10k = 16kΩ. 6kΩ is in series with 16kΩ so R_AB = 6 + 16 = 22kΩ
📌 Example 8: Simplify the given circuit. Solution: 1kΩ is in series with 2kΩ so their combined effect = 1+2 = 3kΩ. 3kΩ is in parallel with 6kΩ. 3k||6k = (3 × 6)/(6+3) = 18/9 = 2kΩ. 10kΩ is in series with 2kΩ, therefore, their combined effect = 10k+2k = 12kΩ. 12kΩ is in parallel with 6kΩ, hence 12k||6k = (12 × 6)/(12+6) = 4kΩ. 2kΩ is in series with 4kΩ, combined effect = 2+4 = 6kΩ. 6kΩ is in parallel with 6kΩ, therefore, 6k||6k = (6 × 6)/(6+6) = 36/12 = 3kΩ. 3kΩ is in series with 9kΩ, therefore, combined effect = 3k+9k = 12kΩ. 12kΩ is in parallel with 4kΩ so 12k||4k = (12 × 4)/(12+4) = 48/16 = 3kΩ. 2kΩ is in series with 3kΩ so R_AB = 2k+3k = 5kΩ
⭐ Key Takeaways
The most critical skills from this lecture are: recognizing whether resistors are connected in series (same current path, end-to-end) or in parallel (same voltage across them, connected to the same two nodes); correctly applying the simple additive formula (R_eq = R1 + R2 + ...) for series circuits and the reciprocal formula (1/R_eq = 1/R1 + 1/R2 + ... or the product-over-sum rule for two resistors) for parallel circuits; and systematically simplifying complex resistor networks by combining pairs of series or parallel resistors step-by-step, working from the innermost combinations outward until only a single equivalent resistor remains between the two terminals of interest.
🧠 Quick Revision Questions
- A 5Ω resistor and a 7Ω resistor are connected in series. What is their equivalent resistance?
- A 12Ω resistor and a 4Ω resistor are connected in parallel. What is their equivalent resistance?
- What is the general formula for the equivalent resistance of N resistors connected in parallel?
- In a series circuit, how does the equivalent resistance compare to the largest individual resistance?
- A circuit has a 6kΩ resistor in series with a parallel combination of a 6kΩ and a 3kΩ resistor. What is the total equivalent resistance seen by the source?
📘 Lecture 4 — Series Parallel Combination
📖 Overview: This lecture introduces the concept of inductance and capacitance in series and parallel combinations. It also covers Ohm's Law, its three forms, and power dissipation in resistance. Understanding these fundamentals is essential for analyzing electrical circuits.
🗂️ Topics Covered
The lecture covers inductance and its units, series and parallel combinations of inductors with examples, capacitance and its units, series and parallel combinations of capacitors with examples, Ohm's Law in three forms (I=V/R, V=IR, R=V/I), the concepts of high voltage with low current and low voltage with high current, volt-ampere characteristics, and power dissipation in resistance with formulas P=I²R and P=V²/R.
📝 Lecture Summary
Inductance
Inductance is the resistance offered by an inductor in a circuit. The unit of inductance is Henry, and it is denoted by L.
🔑 Definition — Inductance (L): The property of an inductor to oppose changes in current, measured in Henrys.
Inductance in Series
If we connect n inductances in series, the combined effect of all these inductances is equal to the sum of individual inductances.
📐 Formula: L_eq = L₁ + L₂ + L₃ + ... + Lₙ → Total series inductance is the sum of all individual inductances.
Inductance in Parallel
If we connect n inductances in parallel, the reciprocal of the combined effect of all these inductances is equal to the sum of reciprocals of individual inductances.
📐 Formula: 1/L_eq = 1/L₁ + 1/L₂ + 1/L₃ + ... + 1/Lₙ → The reciprocal of total parallel inductance equals the sum of reciprocals of each inductance.
📌 Example: Simplify the given inductance circuit. 1mH and 1mH are in series, so their combined effect = 1 + 1 = 2mH.
📌 Example: Simplify the given inductance circuit. 1mH is in series with 4mH and with 3mH, therefore, their effect = 1 + 4 + 3 = 8mH.
📌 Example: Simplify the given inductance circuit. 8mH is in parallel with 8mH, so L_AB = (8 × 8) / (8 + 8) = 64/16 = 4mH.
📌 Example: Simplify the given inductance circuit. 6mH is in parallel with 3mH so 6mH || 3mH = (6 × 3) / (6 + 3) = 18/9 = 2mH. Then, 2mH is in parallel with 4mH, therefore, 2mH || 4mH = (2 × 4) / (2 + 4) = 8/6 = 1.33mH.
📌 Example: Simplify the given inductance circuit. 3mH is in parallel with 6mH so 3mH || 6mH = (3 × 6) / (3 + 6) = 18/9 = 2mH. 2mH is in series with 2mH, therefore, the combined effect of these two = 2 + 2 = 4mH. 4mH is in parallel with 4mH so 4mH || 4mH = (4 × 4) / (4 + 4) = 16/8 = 2mH. 1mH is in series with 2mH so L_AB = 1 + 2 = 3mH.
Capacitance
Capacitance is the resistance offered by a capacitor in a circuit. The unit of capacitance is Farad, and it is denoted by C.
🔑 Definition — Capacitance (C): The ability of a capacitor to store electric charge, measured in Farads.
Capacitance in Parallel
If we connect n capacitances in parallel, the combined effect of all these capacitances is equal to the sum of individual capacitances.
📐 Formula: C_eq = C₁ + C₂ + C₃ + ... + Cₙ → Total parallel capacitance is the sum of all individual capacitances.
Capacitance in Series
If we connect n capacitances in series, the reciprocal of the combined effect of all these capacitances is equal to the sum of reciprocals of individual capacitances.
📐 Formula: 1/C_eq = 1/C₁ + 1/C₂ + 1/C₃ + ... + 1/Cₙ → The reciprocal of total series capacitance equals the sum of reciprocals of each capacitance.
📌 Example: Simplify the given circuit. 2μF capacitor is in series with another 2μF capacitor, their combined effect will be = (2 × 2) / (2 + 2) = 4/4 = 1μF.
📌 Example: Simplify the given circuit. 12μF is in series with 4μF, so their combined effect will be = 48/16 = 3μF. 2μF is in series with 3μF so C_AB = (2 × 3) / (2 + 3) = 1.2μF.
📌 Example: Simplify the given circuit. 4μF is in parallel with 12μF so 12 || 4 = 12 + 4 = 16μF. And 16μF is in series with 3μF so = (3 × 16) / (3 + 16) = 48/19 = 2.5μF. 12μF is in parallel with 2.5μF so their combined effect will be = 12 + 2.5 = 14.5μF. The capacitors are in series so C_AB = (4 × 14.5) / 18.5 = 3.13μF.
OHM’S LAW
If a voltage across a conductor is applied, the current passing through the conductor is directly proportional to the voltage provided temperature remains constant.
🔑 Definition — Ohm's Law: V ∝ I, or V = IR, where 'R' is the resistance of the conductor. Resistance ('R') depends upon the material of the conductor.
The Current I = V/R
If we keep the same resistance in a circuit but vary the voltage, the current will vary. For the general case, for any values of 'V' and 'R', Ohm's Law is I = V/R. Where 'I' is the amount of current through resistance 'R', which is connected across a potential difference 'V'. Volt (V) is the practical unit of potential difference and Ohm (Ω) for resistance, therefore: Ampere = Volts / Ohms. This formula tells us to calculate the Amperes of Current through 'R', simply divide the voltage across 'R' by the Ohms of Resistance.
High Voltage but Low Current
It is important to realize that with high voltage the current can have a low value when there is a very high resistance in the circuit. For example, 1000 (1k) volts applied across 1,000,000 (1M) Ω results in a current of only 0.001 (1m) A. The practical fact is that high voltage circuits usually do have a small value of current in electronic equipment; otherwise, a tremendous amount of power would be necessary for operation.
Low Voltage but High Current
At the opposite extreme, a low value of voltage in a very low resistance circuit can cause a very high current to flow. For example, a 6-volt battery connected across a resistance of 0.001Ω causes 600 A of current to flow: I = V/R = 6v / 0.01Ω = 600 A. Similarly, more 'R' will result in less 'I'.
📌 Example: A heater with a resistance of 8Ω is connected across the 220-volt power line. How much is the current 'I' flowing through the heater coil? Solution: I = V/R = 220/8 = 27.5 A.
📌 Example: A small light bulb with a resistance of 2400Ω is connected across the same 220-volt power line. How much is the current 'I' through the bulb filament? Solution: I = V/R = 220/2400 = 0.09 A = 90 mA.
The Voltage V = IR
It is the other form of the same formula. Besides the numerical calculations possible with the 'IR' formula, it is useful to consider that the 'IR' product means voltage. Whenever there is current through a resistance, it must have a potential difference across its two terminals equal to the product 'IR'. As studied in the last lecture, if there was no potential difference, no electrons could flow to produce the current.
The Resistance R = V/I
As a third and final version of Ohm's Law, three factors V, I, and R are related by the formula R = V/I. As studied in the last lecture, physically, a resistance can be considered as some material with elements having an atomic structure that allows free electrons to drift through it. Electrically, a more practical and general way of considering resistance is simply as a V/I ratio.
📌 Example: A conductor allows 1 A of current with 10 volts applied at its ends. How much will be the resistance of the conductor? Solution: R = V/I = 10/1 = 10 ohm.
The Linear Proportion Between V & I
The Ohm's law formula V = IR states that V and I are directly proportional for any one value of R. This relation is true for constant values of R.
Volt-Ampere Characteristics
The graph in the figure is called the volt-ampere characteristic of R. It shows how much current the resistor allows for different voltages.
💡 Why this matters: The volt-ampere characteristic visually demonstrates the linear relationship between voltage and current for a fixed resistance, which is the foundation of Ohm's Law.
Power Dissipation in Resistance
When current flows through a resistance, heat is produced due to friction between the moving free electrons and the atoms which obstruct the path of electron flow. The heat is evidence that power is used in producing current. The electric energy converted to heat is considered to be dissipated or used up because the calories of work cannot be returned to the circuit as electric energy. Since power is dissipated in the resistance of a circuit, it is convenient to express the power in terms of resistance R. The formula P = V × I can be arranged as follows:
- Substituting IR for V: P = V × I = IR × I = I²R. This is the common form of the formula because of heat produced in a resistance due to current R.
- For another form, substitute V/R for I: P = V × I = V × V/R = V²/R.
In all the formulae, V is the voltage across R in ohms, producing the current in amperes, for power in Watts.
⭐ Key Takeaways
The key takeaways from this lecture are that inductors in series add directly while inductors in parallel follow the reciprocal sum formula, exactly opposite to resistors. Similarly, capacitors in parallel add directly while capacitors in series follow the reciprocal sum formula, also opposite to resistors. Ohm's Law provides three fundamental relationships—V=IR, I=V/R, and R=V/I—which are essential for circuit analysis, and the volt-ampere characteristic for a fixed resistance is a straight line showing linear proportionality. Finally, power dissipated in a resistance can be calculated using either P=I²R or P=V²/R, both derived from the basic power formula P=VI.
🧠 Quick Revision Questions
- What is the formula for total inductance when two inductors of 4mH and 6mH are connected in series?
- What is the formula for total capacitance when two capacitors of 3μF and 6μF are connected in parallel?
- State Ohm's Law in words and write its three mathematical forms.
- Using Ohm's Law, what is the current through a 10Ω resistor connected to a 5V battery?
- What are the two formulas for calculating power dissipated in a resistor, and from which basic formula are they derived?
📘 Lecture 5 — AC, DC Current, voltages
📖 Overview: This lecture introduces the fundamental concepts of ideal and dependent sources in circuit theory, distinguishing between direct current (DC) and alternating current (AC) quantities. It also covers the practical applications of Ohm's law and introduces voltage divider principles for series circuits, which are essential for circuit analysis.
🗂️ Topics Covered
The lecture begins by defining ideal voltage and current sources with their graphical representations, then explains direct and alternating quantities. It covers dependent or controlled sources including voltage-controlled and current-controlled voltage and current sources. Several examples illustrate Ohm's law calculations, and the lecture concludes with the concept of voltage dividers and series voltage division formulas with practical examples.
📝 Lecture Summary
TYPES OF SOURCES:
An ideal voltage source is a source in which terminal voltage remains the same independent of the amount of current drawn. The graph shows V as independent of I — whatever the value of x (current), the value of y (voltage) will remain the same.
🔑 Definition — Ideal Voltage Source: a source where terminal voltage remains constant regardless of current drawn 📐 Graph: V is independent of I → voltage is constant across all current values
The dc voltage source is symbolically represented with a battery symbol showing positive and negative terminals.
An ideal current source is a source which gives constant current independent of the terminal voltage. The graph shows I is independent of V.
🔑 Definition — Ideal Current Source: a source that gives constant current regardless of terminal voltage 📐 Graph: I is independent of V → current is constant across all voltage values
DIRECT VOLTAGE AND QUANTITIES
Direct voltage is the voltage which is independent of time, and its magnitude and direction do not change with time.
Direct quantities are quantities whose magnitude and direction do not change with time (for example V or I).
ALTERNATING QUANTITIES
Alternating quantities are quantities whose magnitude and direction change with respect to time (for example V or I).
DEPENDENT OR CONTROLLED SOURCES
There are two types of dependent voltage sources:
- Voltage controlled voltage source (VCVS) — the source whose magnitude is controlled by voltage
- Current controlled voltage source (CCVS) — a source whose voltage is controlled by current
For current sources: 3. Voltage controlled current source (VCCS) — if magnitude of current is controlled by input voltage 4. Current controlled current source (CCCS) — if magnitude of the current is controlled by input current
💡 Why this matters: Dependent sources model real-world devices like transistors and operational amplifiers where output is controlled by an input signal.
EXAMPLES USING OHM'S LAW
Example: A battery of 10 V is applied across a resistor of 3kΩ.
- By Ohm's law: I = V/R = 10/3k = 3.33 mA
Example: Calculate the current I through a circuit with 2kΩ and 3kΩ in series, with 10V applied.
- Combined resistance = 2k + 3k = 5kΩ
- I = V/R = 10/5k = 2 mA
Example: Calculate the current through resistors of 25Ω, 10Ω, and 5Ω in series with 40V.
- Combined resistance = 25 + 10 + 5 = 40Ω
- I = V/R = 40/40 = 1 A
Example: Find R₁ when current is 5mA and voltage is 10V.
- R₁ = V/I = 10V/5mA = 2kΩ
Example: Find V when current through 10kΩ resistor is 3mA.
- V = IR = 10k × 3mA = 30V
Example: Find V when 5kΩ and 10kΩ are in series with 2mA current.
- Combined resistance = 5k + 10k = 15kΩ
- V = IR = 2mA × 15k = 30V
Example: Calculate current through all resistors in a complex circuit.
- 3kΩ || 6kΩ = (3×6)/(3+6) = 18/9 = 2kΩ
- 2kΩ in series with 2kΩ = 4kΩ
- 3kΩ in series with 1kΩ = 4kΩ
- 4kΩ || 4kΩ = 16/8 = 2kΩ
- Final: 6kΩ + 2kΩ + 4kΩ = 12kΩ
- I = 12V/12kΩ = 1mA
Example: Find current through a circuit with 20V.
- 3kΩ || 6kΩ = 2kΩ
- 4kΩ + 2kΩ = 6kΩ
- 6kΩ || 12kΩ = (6×12)/(12+6) = 72/18 = 4kΩ
- Final: 2kΩ + 4kΩ + 4kΩ = 10kΩ
- I = 20V/10kΩ = 2mA
VOLTAGE DIVIDERS AND CURRENT DIVIDERS
Any series circuit is a voltage divider. The IR drops are proportional parts of the applied voltage. Special formulae can be used for voltage and current division as shortcuts in calculations. The voltage division formula gives the series voltage even when the current is not known.
SERIES VOLTAGE DIVIDERS
- The current is the same in all resistances in a series circuit
- The voltage drop equals the product IR
- IR voltages are proportional to series resistances
- A higher resistance has a greater IR voltage than a lower resistance
- Equal resistances have the same IR drop across each resistance
- If R₁ is double R₂, then V₁ will be double V₂
📐 Formula: Voltage Division Rule: V = (R/Rₜ) × Vₜ
- Where V is voltage across resistor R, Rₜ is total resistance, Vₜ is total applied voltage
- Meaning: The voltage across any resistor in a series circuit equals its proportional share of the total resistance multiplied by the total voltage
Example: Calculate voltage drop across 4kΩ resistor (circuit with 10V across 4kΩ and 6kΩ in series).
- V₄ₖ = (4/10) × 10 = 4 volts
Now calculate voltage drop across 6kΩ resistor:
- V₆ₖ = (6/10) × 10 = 6 volts
Example: Calculate the power dissipated in a circuit with 12V source.
- Step 1: 12kΩ || 12kΩ = 6kΩ
- Step 2: 6kΩ + 2kΩ = 8kΩ
- Step 3: 8kΩ || 4kΩ = 2.66kΩ
- Step 4: 2.66kΩ || 8kΩ = 2kΩ
- Step 5: 2kΩ || 4kΩ = 1.33kΩ
- Total current: I = 12V/1.33kΩ = 9.022 mA
- Power dissipation: P = VI = 12 × 9.022mA = 108.26 mW
⭐ Key Takeaways
The key distinction between ideal voltage and current sources must be memorized: an ideal voltage source maintains constant voltage regardless of current drawn, while an ideal current source maintains constant current regardless of terminal voltage. Dependent sources are controlled by either voltage or current at another point in the circuit and exist in four types (VCVS, CCVS, VCCS, CCCS). Direct quantities have constant magnitude and direction, while alternating quantities change with time. Ohm's law (V=IR) is applied repeatedly to simplify complex resistor networks by combining series and parallel resistors. The voltage division rule V = (R/Rₜ) × Vₜ is essential for finding voltage drops across individual resistors in series without calculating current first, and power dissipation is calculated as P = VI.
🧠 Quick Revision Questions
- What is the key difference between an ideal voltage source and an ideal current source?
- List the four types of dependent or controlled sources and explain what controls each one.
- What distinguishes direct quantities from alternating quantities?
- A 10V source is connected across resistors of 2kΩ, 3kΩ, and 5kΩ in series. Using the voltage division rule, find the voltage drop across the 3kΩ resistor.
- If two resistors of 4kΩ each are in parallel, what is their equivalent resistance? If this combination is in series with a 2kΩ resistor and 12V is applied, what is the total current?