π Lecture 37 β (Peak Inverse Voltage (PIV) - Full wave rectifier)
π Overview: This lecture covers the analysis of negative half wave rectifiers and introduces the concept of Peak Inverse Voltage (PIV). It then transitions to the full wave rectifier, explaining its circuit operation, the role of the center-tapped transformer, and how to calculate load voltage and current values. Understanding PIV is critical for diode selection, and full wave rectification is essential for more efficient DC power conversion.
ποΈ Topics Covered
The lecture begins with a method for analyzing negative half wave rectifiers by adapting positive half wave analysis. It then defines Peak Inverse Voltage (PIV) for half wave rectifiers. The main focus is on the full wave rectifier, including its circuit components, the function of the center-tapped transformer, basic circuit operation during both half cycles, and formulas for calculating peak load voltage and average DC load voltage. Worked examples demonstrate these calculations.
π Lecture Summary
Negative Half Wave Rectifiers:
The analysis of a negative half wave rectifier is nearly identical to that of a positive half wave rectifier. The only difference is that the voltage polarities are reversed. A simple method for performing the mathematical analysis is:
- Analyze the circuit as if it was a positive half wave rectifier.
- After completing calculations, change all voltage polarity signs from positive to negative.
EXAMPLE: Determine the dc output voltage for the circuit shown in the fig. SOLUTION: We shall start by solving the circuit as if it was a positive half wave rectifier. First, V2(pk) = 48Vrms / 0.707 = 67.9 Vpk And, VL(PK) = V2(pk) β 0.7 = 67.2 Vpk Finally, Vave = Vpk / Ο = 21.39 Vdc Now we will simply change all positive voltage values to negative voltage values. V2(pk) = -67.9 Vpk VL(pk) = -67.2 Vpk Vave = -21.39 Vdc
Peak Inverse Voltage (PIV):
The maximum amount of reverse bias that a diode will be exposed to in a rectifier is called the peak inverse voltage or PIV of the rectifier. For the half wave rectifier, the value of PIV is found as: π Formula: PIV = V2(pk) β The peak inverse voltage across the diode is equal to the peak secondary voltage of the transformer. The basis for this equation is that when the diode is reversed biased, there is no voltage drop across the load. Therefore, all of V2 is dropped across the diode in the rectifier.
Full Wave Rectifier:
The full wave rectifier consists of two diodes and a resistor, as shown in the fig (a). The result of this change in circuit is illustrated in fig (b), where the output from the full wave rectifier is compared with that of a half wave rectifier. Note that the full wave rectifier has two positive half cycles out for every one produced by the half wave rectifier. The transformer shown in the fig. is a center tapped transformer. This type of transformer has a load connected to the center of the secondary winding. The voltage from the center tap to each of the outer windings is equal to one half of the secondary voltage. For example, a 24V center tapped transformer has 12V from the center tap to each outer terminal. Center tapping plays a major role in the operation of the full wave rectifier. For this reason, the full wave rectifier can not be line operated, meaning it cannot be connected directly to the AC input like the half wave rectifier can.
Basic Circuit Operation
Figure shows the operation of the full wave rectifier during one complete cycle of the input signal. During the positive half cycle of the input, D1 is forward biased. Using ideal operating characteristics of the diode, VL can be found. When the polarity of the input reverses, D2 is forward biased, and D1 is reverse biased. The direction of the current through the load will not change even though the polarity of the transformer secondary will. Thus, another positive half cycle is produced across the load.
Calculating Load Voltage and Current Values:
Using the practical diode model, the peak load voltage for a full wave rectifier is found as: π Formula: VL(pk) = V2(pk)/2 β 0.7 β The peak load voltage is half the peak secondary voltage minus the diode voltage drop. The full wave rectifier will produce twice as many output pulses as the half wave rectifier. For this reason, the average load voltage for the full wave rectifier is found as: π Formula: Vave = 2VL(pk) / Ο β The average DC voltage is two times the peak load voltage divided by pi. Or, Vave = 0.636 VL(pk)
EXAMPLE: Determine the dc load voltage for the circuit shown in the fig. SOLUTION: Primary voltage is in rms, so we can calculate the peak voltage: V1(pk) = Vrms / 0.707 = 75 / 0.707 = 106.08 Vpk. Primary voltage and turn ratio is known so we can determine the secondary voltage: V2(pk) = (N2/N1) V1pk = 1/4 (106.08) = 26.52 Vpk. Now load voltage can be calculated as: VL(pk) = V2(pk)/2 β 0.7 = 26.52/2 - 0.7 = 12.56 Vpk. Now dc value of the voltage can be calculated as: Vave = 2VL(pk) / Ο = 0.636 (12.56) = 7.98 Vdc.
EXAMPLE: Determine the values of VL(pk) and Vave for the circuit shown in the fig. SOLUTION: The transformer is rated at 30 Vac. Therefore, the value of V2(pk) is found as: V2(pk) = 30 Vac / 0.707 = 42.2 Vpk. The peak load voltage can now be found as: VL(pk) = V2(pk) / 2 β 0.7 = 21.2 β 0.7 = 20.5 Vpk. Finally, the dc load voltage is found as: Vave = 2VL(pk) / Ο = 41 Vpk / Ο = 13.05 Vdc.
β Key Takeaways
The critical takeaways for the exam are: first, you must know the formula and concept of Peak Inverse Voltage (PIV = V2(pk)) for a half-wave rectifier. Second, understand that a center-tapped transformer splits the secondary voltage in half for a full-wave rectifier, so VL(pk) = V2(pk)/2 β 0.7V. Third, the average DC output voltage for a full-wave rectifier is twice that of a half-wave rectifier, calculated as Vave = 2VL(pk)/Ο or 0.636VL(pk). Fourth, master the step-by-step calculation process of converting RMS primary voltage to peak primary, then using the turns ratio to find peak secondary, and finally using the correct formulas to find peak load and average DC voltages. Finally, remember that in a full-wave rectifier, current always flows in the same direction through the load, providing two output pulses per input cycle.
π§ Quick Revision Questions
- What is the formula for the Peak Inverse Voltage (PIV) of a half-wave rectifier?
- What is the critical difference in the transformer used in a full-wave rectifier compared to a half-wave rectifier, and why is it important?
- What is the formula for calculating the peak load voltage (VL(pk)) in a full-wave rectifier using the practical diode model?
- How does the average DC output voltage (Vave) of a full-wave rectifier compare to that of a half-wave rectifier, assuming the same peak voltage at the secondary?
- A full-wave rectifier uses a center-tapped transformer with a 50Vrms secondary (from end to end). Calculate the peak load voltage and the average DC output voltage.
π Lecture 38 β (Negative full wave rectifier - Full wave bridge rectifier)
π Overview: This lecture extends the analysis of full-wave rectifiers to include current calculations, negative full-wave rectifiers, and the full-wave bridge rectifier. It explains how to compute peak and average load currents, introduces the concept of peak inverse voltage (PIV) for center-tapped rectifiers, and details the operation and advantages of the bridge rectifier circuit.
ποΈ Topics Covered
The lecture begins with calculating peak and average load currents using Ohm's law through worked examples. It then introduces the negative full-wave rectifier, explaining how reversing diode polarity changes output polarity. Peak Inverse Voltage (PIV) is defined for full-wave rectifiers, including practical considerations for diode drops. Finally, the full-wave bridge rectifier is presented, covering its circuit operation, advantages over the center-tapped design, and calculation of load voltage/current including the effect of two diode drops.
π Lecture Summary
CALCULATING CURRENTS:
Once peak and average load voltages are known, Ohm's law is used to find corresponding currents. The formulas are I_L(pk) = V_L(pk) / R_L and I_ave = V_ave / R_L.
π Definition β I_L(pk): Peak load current, the maximum current flowing through the load during one cycle. π Definition β I_ave: Average (DC) load current, the direct current equivalent delivered to the load.
π Formula: I_L(pk) = V_L(pk) / R_L β The peak current equals peak voltage divided by load resistance. π Formula: I_ave = V_ave / R_L β The average current equals average voltage divided by load resistance.
π Example: For the circuit from last lecture with V_L(pk) = 20.5V, V_ave = 13.05V, and R_L = 5.1kΞ©: I_L(pk) = 20.5V / 5.1kΞ© = 4.02 mA I_ave = 13.05V / 5.1kΞ© = 2.56 mA
π Example: For a circuit with a 24V RMS transformer (V_2(pk) = 24V/0.707 = 33.94V_pk), a center-tap yields V_L(pk) = V_2(pk)/2 β 0.7V = 16.27V_pk. V_ave = 0.636 Γ V_L(pk) = 10.34V_dc. With R_L = 8kΞ©: I_L(pk) = 16.27V / 8kΞ© = 2.03 mA; I_ave = 10.34V / 8kΞ© = 1.29 mA.
π‘ Why this matters: These current values are essential for specifying components like diodes and load resistors, ensuring they can handle the peak and average power.
NEGATIVE FULL WAVE RECTIFIER:
The negative full wave rectifier produces a negative output voltage by reversing the direction of all diodes in a positive full-wave rectifier. The analysis is identical to the negative half-wave rectifier, except both halves of the input cycle are used.
π Definition β Negative full wave rectifier: A full-wave rectifier with reversed diode polarity, producing a negative DC output voltage with respect to ground.
π Example: Reversing all diodes in a center-tapped full-wave rectifier circuit (as shown in the lecture fig.) results in the same waveform but negative polarity, with the load voltage negative relative to ground.
PEAK INVERSE VOLTAGE:
For a full-wave center-tapped rectifier, when one diode is reverse biased, the voltage across it is approximately V_2(pk). Since the peak load voltage is V_2(pk)/2, the PIV equals twice the peak load voltage. With diode drops, a more accurate formula subtracts 0.7V.
π Definition β PIV (Peak Inverse Voltage): The maximum reverse voltage a diode must withstand without breaking down.
π Formula: PIV = 2 Γ V_L(pk) (ideal) β The inverse voltage is twice the peak load voltage because the full secondary voltage (minus the load) appears across the off diode. π Formula: PIV = V_2(pk) β 0.7 (practical) β Accounts for the forward drop of the conducting diode in series.
π‘ Why this matters: Proper PIV rating prevents diode failure. In center-tapped rectifiers, the PIV is high; bridge rectifiers have lower PIV requirements.
FULL WAVE BRIDGE RECTIFIER:
The full wave bridge rectifier uses four diodes and does not require a center-tapped transformer. Its advantages:
- Can be coupled directly to the AC power line.
- Peak output voltage is nearly double that of a center-tapped rectifier using the same secondary voltage, yielding higher DC voltage.
π Definition β Bridge rectifier: A full-wave rectifier using four diodes in a bridge configuration, with two diodes conducting during each half-cycle.
BASIC CIRCUIT OPERATION:
Conduction alternates between two diode pairs: D1 and D3 conduct during the positive half-cycle, while D2 and D4 conduct during the negative half-cycle. Current through the load always flows in the same direction.
π Example: During the positive half-cycle of V_2, D1 (anode positive) and D3 (cathode negative) are forward-biased, allowing current through R_L. During the negative half-cycle, D2 and D4 conduct, again producing current in the same direction through R_L.
CALCULATING THE LOAD VOLTAGE AND CURRENT VALUES:
Without a center-tap, the ideal peak load voltage is V_L(pk) = V_2(pk). Considering two diode drops (0.7V each), the practical peak load voltage is V_L(pk) = V_2(pk) β 1.4V. Average voltage is then V_ave = 2V_L(pk)/Ο.
π Formula (ideal): V_L(pk) = V_2(pk) β No voltage division occurs, giving higher output. π Formula (practical): V_L(pk) = V_2(pk) β 1.4 β Accounts for two series diodes conducting.
π Example: For a bridge rectifier with a 12V RMS transformer (V_2(pk) = 16.97V_pk) and R_L = 12kΞ©: V_L(pk) = 16.97V β 1.4V = 15.57V_pk V_ave = (2 Γ 15.57V) / Ο = 9.91V_dc I_ave = 9.91V / 12kΞ© = 825.8 ΞΌA
β Key Takeaways
The bridge rectifier is the preferred full-wave design because it doubles the output voltage compared to the center-tapped type without requiring a center-tapped transformer, making it more efficient and cost-effective. Currents are found directly from voltages using Ohm's law. PIV for a center-tapped full-wave rectifier is twice the peak load voltage (or V_2(pk)), and must account for the 0.7V drop in practical circuits. The bridge rectifierβs PIV per diode is lower than in the center-tapped design, an additional advantage. Always include diode voltage drops (1.4V for bridge, 0.7V for center-tapped when applicable) for accurate results.
π§ Quick Revision Questions
- How is I_ave calculated for a full-wave rectifier given V_ave and R_L?
- What is the key structural difference between a negative and positive full-wave rectifier?
- What is the PIV formula for a practical center-tapped full-wave rectifier?
- Why does the bridge rectifier produce a higher peak output voltage than the center-tapped rectifier with the same transformer?
- In a bridge rectifier, which diode pairs conduct during the positive half-cycle?
π Lecture 39 β (Filters - Clippers - Series clippers)
π Overview: This lecture discusses the Peak Inverse Voltage (PIV) in bridge rectifiers and introduces filtering techniques used to smooth rectifier output. It then focuses on diode clippers, particularly series clippers, explaining how they clip portions of an input signal and how adding a DC battery modifies the clipping threshold.
ποΈ Topics Covered
This lecture covers the analysis of Peak Inverse Voltage in bridge rectifiers using the ideal diode model. It introduces filters, primarily the capacitor filter, and explains its charge/discharge action for reducing output voltage variations. The lecture then defines clippers, outlines important points for their analysis, and categorizes them into series and parallel types. A detailed explanation of series clippers is provided, including the effect of adding a DC battery, with supporting examples and calculations for output waveforms.
π Lecture Summary
PEAK INVERSE VOLTAGE:
Using the ideal diode model, the Peak Inverse Voltage (PIV) of each diode in the bridge rectifier is equal to Vβ. This is the same voltage applied to the diode in the full-wave center-tapped rectifier. To illustrate, in a given figure, two things are done: (1) the conducting diodes (Dβ and Dβ) are replaced by straight wires, and (2) the positive side of the secondary is labeled A and the negative side B. Connecting the common A points and B points gives an equivalent circuit. With this circuit, you can see that the two reverse-biased diodes and the secondary of the transformer are all in parallel. Since parallel voltages are equal, the PIV across each diode is equal to Vβ. The same situation will exist for Dβ and Dβ when they are reverse-biased.
FILTERS:
Filters are used in power supplies to reduce the variations in the rectifier output signal. The goal is to produce a constant DC output voltage, so it is necessary to remove as much of the rectifier output variations as possible.
The capacitor filter is the most basic and commonly used filter type. This filter is simply a capacitor connected in parallel with the load resistance. The filtering action is based on the charge/discharge action of the capacitor. During the positive half-cycle of the input, Dβ will conduct and the capacitor will charge rapidly. As the input starts to go negative, Dβ will turn off, and the capacitor will slowly discharge through the load resistance. As the input from the rectifier drops below the charged voltage of the capacitor, the capacitor acts as the voltage source for the load. It is the difference between the charge and discharge times of the capacitor that reduces the variation in the rectifier output voltage. This difference is caused by two distinct RC time constants in the circuit.
π‘ Why this matters: The capacitor filter is essential for converting a pulsating DC from a rectifier into a smoother, more constant DC voltage suitable for powering electronic circuits.
CLIPPERS:
There are a variety of diode networks called clippers that have the ability to clip off a portion of the input signal without distorting the remaining part of the alternating waveform. The half-wave rectifier is the simplest form of diode clipper. Depending on the orientation of the diode, the positive or negative region of the input signal is "clipped" off.
IMPORTANT POINTS FOR CLIPPERS: (1) Make a sketch in your mind about the response of the network. (2) Determine the applied voltage (Transition Voltage) that causes a change in the diode bias. (3) Be continuously aware of the defined terminal and polarity of Vβ. (4) Sketch the input signal on the top and the output at the bottom to determine the output at instantaneous points of the input.
TYPES OF CLIPPERS: There are two general categories of clippers: (1) Series and (2) Parallel.
SERIES CLIPPERS: The series configuration is defined as one where the diode is in series with the load, as in a half-wave rectifier.
ADDITION OF A BATTERY IN THE SERIES CLIPPER CIRCUIT: In the figure, the direction of the diode suggests that the signal Vα΅’ must be positive to turn it on. The DC supply further requires that the voltage Vα΅’ be greater than V volts to turn the diode on. The negative region of the input signal is pressuring the diode into the off region.
To determine the applied voltage that will cause a change in state for the diode, the ideal diode transition occurs at the point on the characteristic where Vd = 0 and Id = 0. In this case, the transition will occur at Vα΅’ = V.
When the diode is short-circuited, the output voltage Vβ can be calculated by applying KVL: Vα΅’ β V β Vβ = 0, so Vβ = Vα΅’ β V. In this case, Vβ = Vβ β V.
π Definition β Peak Inverse Voltage (PIV): The maximum reverse voltage that a diode must withstand without breaking down. π Formula for PIV (bridge rectifier): PIV = Vβ (the secondary voltage) β This means each diode in a bridge rectifier must block a reverse voltage equal to the full secondary voltage. π Example: In a bridge rectifier circuit, when Dβ and Dβ are conducting, Dβ and Dβ are reverse-biased. The equivalent circuit shows Dβ and Dβ in parallel with the transformer secondary. Since parallel components have the same voltage, the PIV across each of these diodes is equal to the secondary voltage, Vβ.
EXAMPLE: Determine the output waveform for the network shown. SOLUTION: The equivalent circuit is drawn. Applying KVL: Vβ = Vα΅’ + 5V. The transition voltage = 5V. When the diode is off, Vβ = VR = iDR = (0)R = 0V (no diode current is flowing).
EXAMPLE: Determine the output for the square wave input shown in the figure. SOLUTION: In the positive half cycle, the diode is in the short circuit condition and by KVL: Vβ = 20 + 5 = 25V. For the negative half cycle, when Vα΅’ = -10V, the result is placing the diode in the reverse condition.
β Key Takeaways
For the exam, you must be able to state that the PIV for each diode in a bridge rectifier equals Vβ. You need to understand that capacitor filters reduce output voltage variations through their charge and discharge cycles. It is critical to know that clippers are diode networks that clip off a portion of the input signal and are categorized as series or parallel. For series clippers with a DC battery, remember that the transition voltage equals the battery voltage, and the output voltage during conduction is Vβ = Vα΅’ β V (or Vβ = Vα΅’ + V, depending on battery polarity). Finally, you must be proficient in applying KVL to determine the output waveform for given input signals.
π§ Quick Revision Questions
- What is the Peak Inverse Voltage (PIV) across each diode in a bridge rectifier, assuming an ideal diode model?
- Briefly explain how a capacitor filter smooths the output of a rectifier.
- What are the two general categories of clippers?
- In a series clipper circuit with an added DC battery, what defines the transition voltage for the diode?
- For the example with a square wave input of +20V and -10V, and a 5V battery in series with the diode, what is the output voltage for the negative half-cycle?
π Lecture 40 β (Parallel Clippers - Clamper)
π Overview: This lecture covers parallel clipper circuits and clamper circuits. It explains how to determine the output voltage for these circuits, including the effects of using ideal versus silicon diodes. The analysis methods for clamping circuits, including the crucial role of the capacitor's charging and discharging, are also thoroughly detailed.
ποΈ Topics Covered
The lecture begins with the definition and analysis of parallel clippers, including an example determining the output voltage for an ideal diode and then a silicon diode. The second half introduces clampers, listing key points for analysis and providing examples of a biased clamper circuit with both ideal and silicon diodes, including the calculation of output waveforms.
π Lecture Summary
PRALLEL CLIPPER
The parallel clipper configuration has the diode in a branch parallel to the load.
π Definition β Parallel Clipper: A clipping circuit where the diode is placed in a branch that is parallel to the load.
π Example: Determine the output voltage for the network shown in the fig. An input voltage Vi swings from +16V to -20V. The circuit has a 4V battery, a resistor R, and a diode in parallel with the load. When the diode is OFF (positive half cycle), the output voltage (Vo) is taken across the load. When the diode is ON (negative half cycle), it clamps the circuit. Solution:
- To find the transition voltage, set Id = 0 and Vd = 0.
- Applying KVL: Vi - Id*R - 4V = 0 => Vi - 0 - 4V = 0 => Vi = 4V is the transition voltage.
- This means the diode is ON for Vi < 4V and OFF for Vi > 4V.
- For the positive half cycle (Vi > 4V, diode OFF), the voltage across the load (VL) equals the output voltage (Vo).
- V0 = VL = 16 Volts.
π Example: Repeat the previous example, but assuming the diode is a silicon diode (VT = 0.7V), and draw its output. Solution:
- The diode will be ON for the negative half cycle.
- To find the transition voltage, apply Id = 0 and Vd = 0.7V.
- The transition voltage (VT) is the input voltage at which the diode just starts to conduct. KVL: Vi + Vd - 4V = 0 => Vi = 4V - Vd = 4V - 0.7V = 3.3V.
- This means the voltage across the diode must be 0.7V for it to conduct. The circuit will reach this state when the input Vi is 3.3V.
- For the positive half cycle (when the diode is OFF), the output voltage is still the input voltage.
- V0 = VL = 16V.
π‘ Why this matters: The 0.7V drop of the silicon diode shifts the transition point of the clipper. In the previous example with an ideal diode, clipping started at 4V. With a silicon diode, clipping starts at 3.3V.
CLAMPERS
Clampers are circuits that clamp the input signal to a different DC level. The total swing of the output is equal to the total swing of the input signal.
π Definition β Clamper: A circuit that adds a DC level to an AC signal without changing its shape or peak-to-peak swing.
For analyzing clampers, remember these points:
- The total swing of the output is equal to the total swing of the input signal.
- Start the analysis by considering that part of the input which will forward bias the diode.
- During the period the diode is 'ON', assume that the capacitor will charge up instantaneously to a level determined by the network.
- During the period for which the diode is 'OFF', assume that the capacitor will hold its charge.
- Throughout the analysis, keep complete awareness of the polarity for V0, so that the proper value of Vo is determined.
π Example: Determine v0 for the network shown in the fig. An input voltage Vi swings from +10V to -20V. The circuit has a 5V battery, a resistor R, a capacitor C, and a diode. Solution:
- Our analysis will begin at time t1 to t2.
- During this period, the diode is forward biased and 'ON'. The circuit shows the capacitor charging.
- Apply KVL to the input loop: -20 + Vc - 5 = 0 => Vc = 25V. The capacitor charges to 25V.
- For the period t2 to t3, the diode is reverse biased and 'OFF'. The capacitor holds its charge of 25V.
- The time constant of the discharging network is determined by the product of RC, which is T = RC = 0.01S.
- KVL across the outer loop during this period: 10 + 25 - V0 = 0 => V0 = 35V.
- The output waveform will have a peak-to-peak swing of 70V (from -35V to +35V) and is shifted up by 25V.
π Example: Repeat the previous example using a silicon diode with VT = 0.7V. Solution:
- For the short circuit state (diode ON, period t1 to t2), the network takes a new appearance.
- Determine V0 using KVL in the output section: +5 - 0.7 - V0 = 0 => V0 = 4.3V.
- For the input section, apply KVL: -20 + Vc + 0.7 - 5 = 0 => Vc = 25 - 0.7 => Vc = 24.3V.
- For the period t2 to t3 (diode OFF), the capacitor holds its charge.
- By KVL in the outer loop: 10 + 24.3 - V0 = 0 => V0 = 34.3V.
β Key Takeaways
A parallel clipper uses a diode in a branch parallel to the load to remove a portion of the input signal. The transition voltage, where clipping begins, is determined by the battery and the diode's turn-on voltage. Clampers shift an entire AC signal to a different DC level, maintaining its shape and swing. The analysis of clampers hinges on the charging of a capacitor to a specific voltage when the diode is forward biased and the capacitor holding that charge when the diode is reverse biased. The inclusion of a silicon diode's forward voltage drop (0.7V) slightly reduces the capacitor's charge and the final output voltage levels compared to an ideal diode.
π§ Quick Revision Questions
- In a parallel clipper with a 5V battery and an ideal diode, at what input voltage does the diode start conducting?
- How does the transition voltage change when an ideal diode in a parallel clipper is replaced by a silicon diode?
- What is the key difference between a clipper and a clamper circuit?
- According to the rules for analyzing clampers, what happens to the capacitor voltage when the diode is OFF?
- In the clamper example with the silicon diode, why was the capacitor's final charge 24.3V instead of 25V?
π Lecture 41 β Diode Logic Gates (OR Gate)
π Overview: This lecture covers diode-based logic gates (OR and AND gates), their circuit analysis with worked examples, then introduces voltage multipliers (half-wave doublers) and their operation, and concludes with zener diode characteristics and shunt regulator concepts. These topics bridge digital logic with analog power electronics.
ποΈ Topics Covered
The lecture begins with diode OR gate configuration and example analysis (finding V and I), then covers diode AND gate with similar example. It transitions to voltage multipliers including half-wave voltage doublers with detailed circuit operation during positive and negative half-cycles. The lecture concludes with zener diode modeling (incremental resistance, equivalent circuit) and zener diode shunt regulator parameters (line regulation, load regulation).
π Lecture Summary
DIODE LOGIC GATES (OR GATE)
The OR gate using diodes produces an output equal to the logical OR of inputs: Y = A + B + C. When multiple inputs are present, the diode with the highest forward bias voltage dominates and conducts, while others remain off.
π Definition β Diode OR Gate: A logic gate where the output is HIGH if any input is HIGH; implemented using diodes that conduct when their anode is more positive than the cathode.
π Formula: Y = A + B + C β output equals the highest input voltage
π Example: Find V and I in the OR gate circuit.
- D1 has 3V applied across it (forward biased), making it conduct more than D2 and D3.
- D2 and D3 are OFF.
- Therefore, V = 3V
- By Ohm's Law: I = (3 - 0)/1k = 3mA
DIODE LOGIC GATES (AND GATE)
The AND gate using diodes produces an output equal to the logical AND of inputs: Y = A Β· B Β· C. The diode with the lowest input voltage at its cathode will conduct, pulling the output down.
π Definition β Diode AND Gate: A logic gate where the output is HIGH only if ALL inputs are HIGH; implemented using diodes with output taken at the common cathode point.
π Example: Find V and I in the AND gate circuit.
- D3 is ON: cathode at +1V, anode at +5V β potential difference 4V (most forward biased).
- D1 and D2: potential difference across D2 is 3V (less than D3, so D3 dominates).
- Due to D3 being fully forward biased, D1 and D2 become reverse-biased and OFF.
- Therefore, V = +1V
- By Ohm's Law: I = (5 - 1)/1k = 4mA
VOLTAGE MULTIPLIERS
Voltage multipliers are circuits that provide a DC output which is a multiple of the peak input voltage. A voltage doubler provides DC output twice the peak input voltage.
π‘ Why this matters: Voltage multipliers are not power generators β when voltage increases by factor N, current decreases by approximately the same factor. Used in low current, high voltage applications (e.g., cathode ray tube in televisions).
HALF-WAVE VOLTAGE DOUBLERS
The half-wave doubler uses two diodes and two capacitors. Assume ideal diodes for analysis.
During negative alternation of input:
- D1 is forward-biased (short circuit), D2 is reverse-biased (open circuit).
- C1 charges until its plate-to-plate voltage equals the source voltage.
- C2 discharges through the load resistance RL.
When input polarity reverses (positive half-cycle):
- D1 is OFF (open), D2 is ON (short).
- C1 (charged to peak value Vs) and the source voltage act as series-aiding voltage sources.
- C2 charges to the sum: 2V_s(pk).
Detailed operation:
- During first half cycle: point x is positive relative to y. Charging current flows through C1 and D1 (forward biased). C1 charges to peak value in T/4. D2 remains OFF.
- During negative half cycle: point x is negative relative to y. Voltage of C1 (Vc1) and Vin are in series (additive). Current flows from y through C2, through D2 (conducting), back to x. C2 charges to magnitude 2Vm.
π Formula (applying KVL): -Vc1 - Vin = Vo Since Vc1 = Vmax, therefore: Vo = -2Vmax (output waveform is negative twice the peak input)
Dual Power Supply
A dual-polarity power supply provides both positive and negative DC output voltages.
ZENER DIODE
In the zener region, the differential voltage and current relationship is given by:
π Formula: βVz = rz βIz Where rz = inverse of the slope (incremental resistance) of zener diode at the operating point.
π Definition β Zener Diode Model: The almost linear i-v characteristic allows modeling as: Vz = Vzo + rz Iz Where Vzo is the knee voltage (practically considered equal to Vzk), valid when Iz > Izk and Vz > Vzo.
ZENER DIODE SHUNT REGULATOR
A regulator must possess two properties:
- No change in Vo with any change in Vs (line regulation)
- No change in Vo with any change in IL (load regulation)
π Formulas:
- Line regulation = βVo / βVs
- Load regulation = βVo / βIL
β Key Takeaways
The most critical concepts from this lecture are: (1) Diode OR gate output equals the highest input voltage, while diode AND gate output equals the lowest input voltage β both rely on which diode is most forward biased. (2) Voltage multipliers, particularly half-wave doublers, charge capacitors sequentially during alternate half-cycles, with the second capacitor charging to twice the peak input voltage through series-aiding sources. (3) Zener diodes operate in the breakdown region with incremental resistance rz, modeled as Vz = Vzo + rz Iz. (4) A shunt regulator's performance is defined by line regulation (βVo/βVs) and load regulation (βVo/βIL). (5) Voltage multipliers conserve power β increasing voltage proportionally decreases current, limiting them to low-current applications.
π§ Quick Revision Questions
- In a diode OR gate with inputs 5V, 3V, and 1V, what is the output voltage and which diodes conduct?
- Why does D3 dominate in the AND gate example even though D2 also has forward bias?
- During which half-cycle does C2 charge to 2Vpk in a half-wave voltage doubler?
- Write the formula for zener diode voltage in terms of Vzo, rz, and Iz.
- What is the difference between line regulation and load regulation in a zener shunt regulator?
π Lecture 42 β (Zener diode-LED-PIN Photodiodes - Tunnel diode)
π Overview: This lecture covers the application of Zener diodes in shunt regulators, providing detailed analysis and design examples. It then introduces Light Emitting Diodes (LEDs), their operating principles and characteristics, followed by brief overviews of PIN Photodiodes and the unique negative resistance region of Tunnel Diodes. This is critical for understanding voltage regulation and optoelectronic devices.
ποΈ Topics Covered
The lecture begins with Zener diode shunt regulators, explaining how to calculate regulation, output voltage, and design parameters like series resistance. Several practical design examples are solved, including finding Vzo, line regulation, load regulation, and power dissipation. The second half introduces LEDs, covering their light emission principle, materials, lead identification, and forward/reverse voltage characteristics. Finally, PIN photodiodes and Tunnel diodes are briefly introduced, focusing on the tunnel diode's negative resistance region between its peak and valley points.
π Lecture Summary
ZENER DIODE SHUNT REGULATOR:
A Zener diode shunt regulator maintains a constant output voltage across a load by using a series resistor (R) and a Zener diode (Dz) in parallel with the load. The Zener diode operates in its breakdown region, keeping its voltage relatively constant despite changes in supply voltage or load current. The regulation depends on the incremental resistance (rz) of the Zener diode and the series resistor.
π Regulation: The ability of a circuit to maintain a constant output voltage despite changes in input voltage or load current. π Formulas for Regulation:
- Line Regulation = rz / (R + rz) β This measures the change in output voltage (Vo) for a change in supply voltage (Vs).
- Load Regulation = - (rz || RL) β This measures the change in output voltage (Vo) for a change in load current (IL).
The output voltage can be found using the Thevenin equivalent model. Let Vzo be the Zener voltage at the knee of the characteristic curve (zero current intercept). π Output Voltage Formula: Vo = Vzo + (Vs β Vzo) * rz / (R + rz) To design the series resistor R, the worst-case conditions of minimum supply voltage (Vsmin) and maximum load current (ILmax) are considered, ensuring the Zener current (Iz) stays above its minimum (Izmin). π Series Resistor Design Formula: R = (Vsmin β Vzo β rz*Izmin) / (Izmin + ILmax)
π Example: A zener diode whose nominal voltage is 10V at 10mA has an incremental resistance of 50Ξ©. What voltage must Ahmad Tulaib expect if Bilal disturbs the settings to half the diode current? What is the value of Vzo of the zener model? Solution:
- Half the current: Current change = -5mA. Vz = 10V - (0.05A)(50Ξ©) = 10V - 0.25V = 9.75V.
- Double the current: Current change = +10mA. Vz = 10V + (0.01A)(50Ξ©) = 10V + 0.5V = 10.5V.
- Finding Vzo: Vzo is the voltage when current decreases by 10mA from the test point. Vzo = 10V - (0.01A)(50Ξ©) = 10V - 0.5V = 9.5V.
π Example: A zener diode exhibits a constant voltage of 5.6V for currents greater than five times the knee current Izk is specified to be 1mA. It is to be used in the design of a shunt regulator fed from a 15V supply. The load current varies over the range 0 to 15mA. Find a suitable value for the resistance R. What is the maximum power dissipation to the zener diode. Solution:
- Minimum Zener Current: Izmin = 5 * Izk = 5 * (1mA) = 5mA.
- Total Current through R: With ILmax = 15mA, the current through R is Ir = Izmin + ILmax = 5mA + 15mA = 20mA.
- Resistance Calculation: R = (Vs β Vz) / Ir = (15V β 5.6V) / 20mA = 9.4V / 0.02A = 470Ξ©.
- Maximum Zener Power: This occurs at no load (IL=0), where all 20mA flows through the Zener. Pz = Vz * Iz = 5.6V * 20mA = 112mW.
π Example: A shunt regulator utilizes a zener diode whose voltage is 5.1V at a current of 50mA and whose incremental resistance is 7Ξ©. The diode is fed from a supply of 15 V nominal voltages through a 200 Ξ© resistor. What is the output voltage at no load? Find the line regulation and load regulation. Solution:
- Find Vzo: Vzo = Vz β rz*Iz = 5.1V β (7Ξ© * 0.05A) = 5.1V β 0.35V = 4.75V.
- Output Voltage (No Load): Vo = Vzo + (Vs β Vzo)rz/(R+rz) = 4.75V + (15V-4.75V)(7Ξ©)/(200Ξ©+7Ξ©) = 4.75V + (10.25*7)/207 = 4.75V + 0.346V = 5.1V.
- Line Regulation: rz/(R+rz) = 7/(200+7) = 33.8mV/V.
- Load Regulation: - (rz || R) = - (7 || 200) = - (7*200)/(7+200) = -1400/207 = -6.8 Ξ© = -6.8 mV/mA.
π Example: Ghania is trying to design a shunt regulator, of about 20V... Two kinds of zener diodes are available: 6.8V devices with rz of 10 Ξ© and 5.1V devices with rz of 30 Ξ©. For the two choices possible, find load regulation. Solution:
- Choice a): Three 6.8V diodes in series give 20.4V. The total incremental resistance is 3 * 10Ξ© = 30Ξ©. Load regulation (neglecting R) = -30Ξ©.
- Choice b): Four 5.1V diodes in series give 20.4V. The total incremental resistance is 4 * 30Ξ© = 120Ξ©. Load regulation (neglecting R) = -120Ξ©.
- π‘ Why this matters: A smaller effective rz results in better (smaller numerical value) load regulation, meaning the output voltage is more stable with changing load current.
π Example: It is required to design a shunt regulator to provide a regulated voltage of about 10V. The available 10V, 1W zener of type 1N4740 is specified to have a 10V drop at a test current of 25mA. At this current its rz is 7 Ξ©. The raw supply available has a nominal value of 20V but can vary as much as Β±25%. The regulator is required to supply a load current of 0 to 20mA. Design for a minimum zener current of 5mA. Solution (Data: Vz=10V, Iz=25mA, rz=7Ξ©, Vs=20VΒ±25%, Izmin=5mA, ΞIL=20mA): a). Find Vzo: Vzo = Vz - Izrz = 10V - 25m(7) = 9.825V. b). Calculate R: Minimum Vs (Vsmin) = 20V - 5V = 15V. Izmin = 5mA occurs when IL is maximum (20mA). R = (Vsmin - Vzo - rzIzmin) / (Izmin + ILmax) = (15 - 9.825 - 0.035) / (5m + 20m) = 5.14V / 25mA = 205.6Ξ©. Use 205Ξ©. c). Line Regulation: rz/(R+rz) = 7/(205+7) = 33mV/V. A Β±25% change in Vs is Β±5V. ΞVo = Β±5V * 33mV/V = Β±165mV. Percentage change = Β±0.165V / 10V * 100% = Β±1.65%. d). Load Regulation: -rz||R = -7||205 = -6.77 Ξ© = -6.77 V/A. From no load (0mA) to full load (20mA), ΞVo = -6.77Ξ© * 20mA = -135.4mV. Percentage change = -0.1354V / 10V * 100% = -1.35%. e). Maximum Zener Current & Power: Occurs at no load (IL=0) and max Vs (Vsmax=25V). Total current = (25V - 9.825V) / (205Ξ© + 7Ξ©) = 15.175V / 212Ξ© = 71.6mA. More precisely, Vz = 9.825V + 71.6m(7) = 10.326V. Pz = 71.6m(10.326) = 739.4mW. This is under the 1W rating.
LIGHT EMITTING DIODES:
LEDs are diodes that emit light when forward-biased. The graphic symbol has two arrows pointing away from the diode, representing emitted light. When electrons in the n-region cross the junction into the p-region, they recombine with holes. This recombination releases energy in the form of a photon of light. The color of the light depends on the semiconductor material (e.g., Gallium, Arsenic, Phosphorus).
- Lead Identification: Since LEDs have clear cases, the leads are often identified by (1) different lengths, (2) a flattened lead (usually the cathode), or (3) a flattened side on the case near the cathode.
LED CHARACTERISTICS:
LEDs have similar characteristic curves to standard pn junction diodes but with different voltage ranges. π Forward Voltage (VF): The voltage drop across the diode when it is conducting and emitting light. It is typically between +1.2V to +4.3V. π Reverse Breakdown Voltage: The voltage at which the diode will break down in reverse bias. It is typically much lower than for standard diodes, ranging from -3V to -10V.
π Definition β PIN Photodiode: A photodiode with an intrinsic (i) layer between the p and n layers. The intrinsic layer increases the depletion region width, allowing for faster response times and higher efficiency in detecting light. It is commonly used in fiber optic communications.
TUNNEL DIODE:
A tunnel diode is a heavily doped (approximately 1000 times more than standard diodes) pn junction diode used in ultra-high frequency (UHF) and microwave applications. Its characteristic curve exhibits a negative resistance region.
The key operating points in the forward bias region are:
- Peak Voltage (Vpk): The voltage at which the forward current reaches its maximum, called Peak Current (Ipk).
- Valley Voltage (Vv): The voltage at which the forward current reaches its minimum, called Valley Current (Iv).
- Negative Resistance Region: The region of operation between Vpk and Vv. In this region, as the forward voltage increases, the forward current decreases (dV/dI is negative), which is the opposite of Ohm's law. This property is useful in high-frequency oscillators and switching circuits.
β Key Takeaways
- A Zener diode shunt regulator uses a series resistor to limit current and a Zener diode in parallel with the load to clamp the output voltage. The Zener's incremental resistance (rz) is a key parameter for calculating regulation.
- Line Regulation (ΞVo/ΞVs = rz/(R+rz)) measures output stability against input voltage changes, while Load Regulation (ΞVo/ΞIL = -rz||R) measures stability against load current changes. A smaller rz value gives better regulation.
- For designing the series resistor R, you must consider the worst-case scenario where the supply voltage is minimum and the load current is maximum, ensuring the Zener has its minimum required current (Izmin) to maintain regulation.
- LEDs convert electrical energy into light when forward-biased, with a forward voltage typically between 1.2V and 4.3V, and a low reverse breakdown voltage. The color of the emitted light depends on the semiconductor material.
- A Tunnel diode has a unique negative resistance region between its peak and valley voltages, where current decreases as voltage increases, making it useful for high-frequency oscillators.
π§ Quick Revision Questions
- What are the two formulas for calculating line regulation and load regulation in a Zener shunt regulator, and what do they physically represent?
- If a Zener diode has a Vz of 12V at 20mA and an rz of 10Ξ©, what is its Vzo and what would its voltage be at a current of 35mA?
- In designing a shunt regulator, why is it important to consider the minimum supply voltage and maximum load current when calculating the value of the series resistor R?
- What is the fundamental physical process that causes an LED to emit light, and what determines the color of that light?
- What is the key characteristic of a Tunnel diode's operating curve between the peak voltage (Vpk) and the valley voltage (Vv), and what is this region called?