π Lecture 30 β (PN Junction Diode - Ideal Diode - Ideal Diode as a Rectifier)
π Overview: This lecture introduces the fundamental semiconductor device called the PN-junction diode and its two key operating regions: forward bias and reverse bias. It then defines the concept of an ideal diode as a unidirectional switch and demonstrates its application as a half-wave rectifier to convert AC to pulsating DC. Understanding these principles is critical for analyzing all diode-based electronic circuits.
ποΈ Topics Covered
The lecture begins with the introduction to the PN junction diode and its schematic symbol. It then explains the conditions and circuit configurations for forward-biased operation, where the diode conducts, followed by reverse-biased operation, where it acts as an open circuit. The concept of the ideal diode is introduced, defined by its zero forward resistance and infinite reverse resistance. Finally, the lecture concludes by applying the ideal diode model to a simple rectifier circuit, showing how it converts a sinusoidal AC input into a unidirectional output voltage.
π Lecture Summary
INTRODUCTION TO THE PN- JUNCTION DIODE.
The schematic symbol for the pn-junction diode is shown. A diode will conduct when the voltage difference between the anode and the cathode exceeds the barrier voltage of approximately 0.3 volts for a germanium diode and 0.7 for a silicon diode.
THE FORWARD BIASED PN-JUNCTION (DIODE)
When the positive terminal of a battery is connected to the anode (P-side) and the negative terminal to the cathode (N-side), the diode is said to be FORWARD-BIASED. The arrow in the symbol points to the more negative potential. Several circuit configurations fulfill this condition:
- Fig. a: Positive terminal connected to anode through a resistor; cathode to neutral. Current (IF) flows.
- Fig. b: Negative terminal connected to cathode; anode through resistor to neutral. Current (IF) flows.
- Fig. c: Positive voltage applied to anode through a resistor; cathode to neutral through a resistor.
- Fig. d: Negative voltage applied to cathode through a resistor; anode to neutral through a resistor.
In all these cases, forward conventional current (IF) is established in the diode.
THE REVERSE - BIASED PN-JUNCTION (DIODE)
When the positive terminal of a battery is connected to the cathode (N-side) and the negative terminal to the anode (P-side), the diode is said to be REVERSE-BIASED. In this condition, the n-type material (cathode) is more positive than the p-type material (anode). This causes the depletion region to widen and prevent current flow. A diode will not conduct when the arrow points to the more positive potential.
- In fig. a and b, the negative terminal is connected to the anode through a resistor and the positive terminal to the cathode. No majority carrier current flows; the diode acts as an open circuit.
- In fig. c and d, the bias conditions are met through connections to neutral.
π Definition β Reverse-Biased Diode: A reverse-biased PN-junction cannot support majority carrier current, but it allows a very small minority carrier current (called reverse current) to flow across the junction. The depletion layer expands, so the diode acts as an open circuit. π‘ Why this matters: The extreme difference in current flow between forward and reverse bias is what makes the diode a useful one-way switch for electronics.
The Ideal Diode
The ideal diode is considered to be a one-way street; it conducts electricity well in one direction but hardly any in the opposite direction. An ideal diode has no resistance in the forward direction and infinite resistance in the reverse direction.
- It is analogous to a light switch (complete circuit = on, open circuit = off) but with the added property of being unidirectional (current flows only from anode to cathode internally).
- A mechanical analogy is a ratchet, which allows motion in one direction only.
- The ideal diode is the most fundamental non-linear circuit element.
- Its i-v characteristic (fig b) shows that for any positive voltage, current flows infinitely (short circuit), and for any negative voltage, current is zero (open circuit).
- When a negative voltage is applied, the diode is reverse-biased and behaves as an open circuit (fig c), also said to be cut off.
- When a positive voltage is applied, the diode is forward-conducting and behaves as a short circuit (fig d) with zero voltage drop, also said to be turned on.
The Ideal Diode as a Rectifier
Rectification is defined as the process of converting an alternating current to a unidirectional current. The rectifier circuit (fig a) consists of a series connection of a diode D and a resistor R.
- With a sinusoidal input voltage (fig b) and assuming an ideal diode:
- During the positive half cycle, the diode is forward-biased (short circuit, fig c). The output voltage VO equals the input voltage vI.
- During the negative half cycle, the diode is reverse-biased (open circuit, fig d). The output voltage VO is zero.
- The resulting output waveform (fig e) is unidirectional and has a finite average (DC) value, even though the input had a zero average value. This circuit is called a rectifier.
π Formula: For an ideal half-wave rectifier circuit: [ V_O = V_I \text{ (during positive half-cycle)} ] [ V_O = 0 \text{ (during negative half-cycle)} ] β This means the circuit passes one polarity of the input signal and blocks the other.
π Example: The lecture provides a problem to draw the transfer characteristic (v0 vs vI) for a given circuit.
β Key Takeaways
The PN junction diode, made of silicon or germanium, conducts only in forward bias when the anode is more positive than the cathode by at least the barrier voltage (0.7V for Si, 0.3V for Ge). In reverse bias, the depletion region widens, preventing majority carrier current and making the diode act as an open circuit, allowing only a tiny minority carrier current. An ideal diode is a theoretical model with zero resistance in forward bias (short circuit) and infinite resistance in reverse bias (open circuit). This unidirectional switching action is essential for rectification, which converts a bipolar AC signal into a unipolar (pulsating DC) signal, as demonstrated in the half-wave rectifier circuit. The transfer characteristic of a diode circuit maps the input voltage to the output voltage based on the diodeβs bias state.
π§ Quick Revision Questions
- What is the typical barrier voltage for a forward-biased silicon diode?
- Describe the behavior of the depletion region in a reverse-biased PN junction.
- What are the two conditions (bias states) of an ideal diode, and what equivalent circuit element does each state represent?
- In a half-wave rectifier circuit with an ideal diode and a sinusoidal input, what is the output voltage during the negative half-cycle of the input?
- Why is an ideal diode considered a "non-linear circuit element"?
π Lecture 31 β Terminal characteristics of the Junction diodes - Forward bias region
π Overview: This lecture covers the terminal characteristics of junction diodes, focusing on the forward bias region. It explains how diodes behave in circuits through detailed examples involving battery charging, ideal diode analysis, and the mathematical i-v relationship that governs diode operation, which is essential for understanding semiconductor device behavior in electronic circuits.
ποΈ Topics Covered
The lecture begins with practical circuit examples analyzing diode conduction angles and current calculations in battery charging circuits. It then examines ideal diode behavior in various biasing configurations to determine current and voltage values. The second half introduces the terminal characteristics of junction diodes, detailing the three operating regions with emphasis on the forward bias region, including the diode equation, thermal voltage, and the scaling constant Iβ.
π Lecture Summary
Example (Battery Charging Circuit)
A circuit for charging a 12-volt battery is analyzed where vβ is a sinusoid with 24 volts peak amplitude. The diode conducts when vβ exceeds 12 volts. The conduction angle is 2ΞΈ, where ΞΈ is given by 24cosΞΈ = 12, so cosΞΈ = 1/2, giving ΞΈ = 60Β° and the conduction angle is 120Β° or one-third of the cycle.
The peak value of the diode current is given by I_d = (24 β 12)/100 = 0.12 A. The maximum reverse voltage across the diode occurs when vβ is at its negative peak and equals 24 + 12 = 36 volts.
Example: Assuming the diodes to be ideal
In fig (a), a positive 5V battery connects to the anode through a 2.5 kΞ© resistor, with the cathode connected to neutral. The diode is in forward biased condition and acts as a short circuit. By Ohm's Law, I = 5/2.5 = 2mA, and V = 0 volts.
In fig (b), the diode is reversed. The 5V battery connects to the cathode through 2.5 kΞ©, with the anode at neutral. The diode is reverse biased and acts as an open circuit, so I = 0mA and V = 5 volts.
In fig (c), a negative 5V battery connects to the anode through 2.5 kΞ©. The diode is reverse biased and acts as an open circuit. I = 0mA and V = -5 volts.
In fig (d), the circuit is same as (c) but the diode is reversed. The diode is forward biased and acts as a short circuit. I = 5/2.5 = 2mA and V = 0 volts.
Example: Finding I and V with ideal diodes
For fig (a), assume both diodes are conducting. V_B = 0 and V_0 = 0. The current through Dβ is I_D2 = (10 β 0)/10 = 1mA. Writing a node equation at B: I + 1 = (0 β (-10))/5, resulting in I = 1mA. Thus Dβ is conducting as assumed, giving I = 1mA and V = 0 volts.
For fig (b), assuming both diodes conduct gives V_B = 0 and V_0 = 0. I_D2 = (10 - 0)/5 = 2mA. The node equation I + 2m = (0 β (-10))/10k yields I = -1mA, which is impossible. Assuming Dβ is off and Dβ is on, I_D2 = (10 β (-10))/15 = 1.33mA, and V_B = -10 + 10 Γ 1.33 = 3.3 volts. Thus Dβ is reverse biased as assumed, giving I = 0 and Vβ = 3.3 volts.
TERMINAL CHARACTERISTICS OF THE JUNCTION DIODES
The characteristic curve consists of three distinct regions: (1) The forward bias region, determined by v > 0, (2) The reverse bias region, determined by v < 0, and (3) The breakdown region, determined by v < -V_ZK.
THE FORWARD BIAS REGION
The forward bias region is entered when the terminal voltage v is positive. The i-v relationship is closely approximated as i = I_s(e^(v/nV_T) β 1). In this equation, I_s is a constant for a given diode at a given temperature and is directly proportional to the area of the diode.
The Voltage V_T is a constant given as V_T = kT/q, where k is Boltzmann's constant (1.38 Γ 10β»Β²Β³ J/K), T is absolute temperature in Kelvin, and q is the magnitude of the electronic charge (1.60 Γ 10β»ΒΉβΉ C). At room temperature (20Β°C), the value of V_T is 25.2mV. The constant n has a value between 1 and 2 depending on the material and physical structure of the diode.
π Definition β Thermal Voltage (V_T): The voltage constant in the diode equation given by V_T = kT/q, approximately 25.2mV at room temperature.
For appreciable current I in the forward direction, i >> I_s, so the diode equation can be modified as i = I_s e^(v/nV_T). This can be given alternatively in logarithmic form as v = nV_T ln(i/I_s).
Considering the forward i-v relationship, the current Iβ corresponding to diode voltage Vβ is Iβ = I_s e^(Vβ/nV_T). Similarly for Vβ, Iβ = I_s e^(Vβ/nV_T). Combining these produces Iβ/Iβ = e^((Vβ β Vβ)/nV_T), which can be rewritten as Vβ β Vβ = nV_T ln(Iβ/Iβ).
EXAMPLE: Scaling Constant Evaluation
A silicon 1mA device displays a forward voltage of 0.7V at a current of 1mA. The junction scaling constant I_s is evaluated for n = 1 or n = 2.
Since i = I_s e^(v/nV_T), then I_s = i e^(-v/nV_T).
π Formula: I_s = i e^(-v/nV_T) β The saturation current equals the diode current multiplied by e raised to the negative voltage divided by n times thermal voltage.
For the 1mA diode: If n = 1: I_s = 10β»Β³ e^(-700/25) = 6.9 Γ 10β»ΒΉβΆ A If n = 2: I_s = 10β»Β³ e^(-700/50) = 8.3 Γ 10β»ΒΉβ° A
The diode conducting 1A at 0.7V corresponds to 1000mA in parallel with a total junction area 1000 times greater, so I_s is also 1000 times greater.
π Example: For a 1A diode (same manufacturer, 0.7V at 1A), if n = 1, I_s = 1000 Γ 6.9 Γ 10β»ΒΉβΆ = 6.9 Γ 10β»ΒΉΒ³ A. If n = 2, I_s = 1000 Γ 8.3 Γ 10β»ΒΉβ° = 8.3 Γ 10β»β· A.
π‘ Why this matters: The scaling constant I_s determines the diode's current-carrying capability at a given voltage and is directly proportional to the junction area, making it critical for designing diodes with specific ratings.
β Key Takeaways
The conduction angle of a diode in a rectifier circuit depends on when the input voltage exceeds the battery voltage, and the peak reverse voltage equals the sum of peak input and battery voltages. Ideal diodes act as short circuits when forward biased and open circuits when reverse biased, allowing straightforward current and voltage calculations using Ohm's Law. The diode's i-v characteristic in the forward bias region follows an exponential relationship i = I_s(e^(v/nV_T) β 1), where V_T = kT/q β 25.2mV at room temperature. The scaling constant I_s is proportional to the diode junction area, so a 1A diode has an I_s 1000 times larger than a 1mA diode. The voltage change required for a tenfold current increase in a diode is approximately nV_T Γ ln(10), which is about 60mV for n = 1 at room temperature.
π§ Quick Revision Questions
- In the battery charging example, what fraction of the cycle does the diode conduct, and what is the peak diode current?
- For an ideal diode, what is its equivalent circuit behavior in forward bias and reverse bias?
- What are the three distinct regions of a diode's terminal characteristic curve?
- Write the diode equation for the forward bias region and define each term (I_s, V_T, n).
- Calculate I_s for a silicon diode with 0.7V forward voltage at 1mA current when n = 1.2 (use V_T = 25mV).
π Lecture 32 β Reverse bias region - Break down region - Analysis of diode circuit
π Overview: This lecture explores diode behavior beyond forward bias, covering the reverse bias and breakdown regions. It then shifts focus to practical circuit analysis techniques, using examples to demonstrate how to determine diode current and voltage in a simple series circuit. Understanding these regions and analysis methods is crucial for designing and troubleshooting diode-based circuits, including voltage regulators.
ποΈ Topics Covered
The lecture begins with multiple worked examples calculating voltage and current changes in diodes using the exponential model. It then formally defines the reverse bias region, explaining the concept of saturation current and leakage. Next, it covers the breakdown region, introducing breakdown voltage and its application in voltage regulation. Finally, it details two methods for analyzing a simple diode circuit: graphical analysis using a load line and iterative analysis, with a step-by-step example.
π Lecture Summary
Example: Consider a silicon diode with n =1.5. Find the change in voltage if the current changes from 0.1mA to 10mA.
This example demonstrates using the diode equation to find the voltage change corresponding to a known current change.
π Definition β Diode Equation: i = Is * e^(v/nVT) describes the current-voltage relationship of a diode. π Formula: v1 β v2 = nVT * ln(I1/I2) β The change in voltage across a diode is proportional to the natural log of the ratio of the two currents. π Example: For n=1.5, VT=25mV, I1=10mA, I2=0.1mA: v1 β v2 = 1.5 * 25mV * ln(10/0.1) = 172.7mV.
Example: A silicon junction diode with n =1 has v = 0.7 volts at i =1mA . Find the voltage drop at i =0.1mA and i = 10mA.
This example uses the same principle to find the new voltage at different currents, given a known operating point.
π Formula: v2 = v1 + nVT * ln(i2/i1) β A practical form to find the new voltage v2, given a reference point (v1, i1). π Example: For n=1, VT=25mV, v1=0.7V at i1=1mA:
- For i2=0.1mA: v2 = 0.7 + 0.025*ln(0.1) = 0.64 volts.
- For i2=10mA: v2 = 0.7 + 0.025*ln(10) = 0.76 volts.
Example: The circuit in the fig. utilize three identical diodes having n=1 and Is = 10^-14 A. Find the value of the current I to obtain an output voltage V0 = 2V, if a current of 1mA is drawn away, what is the change in output voltage.
This example applies the diode equation to a series circuit of three diodes, analyzing the effect of a changing load current.
π Example: With three identical diodes in series, V0=2V means each diode drops 2/3 V. The current I is calculated using the diode equation:
- I = Is * e^(v/nVT) = 10^-14 * e^( (2/3) / 0.025 ) = 3.8mA.
- If 1mA is drawn away, the diode current reduces to 2.8mA. The voltage change per diode is ΞV = nVT * ln(2.8/3.8) = -7.63mV.
- The total decrease in V0 is 3 * 7.63mV = 22.9 mV.
Example: A particular diode conducts 1A at a junction voltage of 0.65 volts and 2A at a junction voltage 0.67 volts. What are its values of n and Is, what current will follow if its junction voltage is 0.7volts?
This example shows how to extract the diode's model parameters (n and Is) from two data points on its i-v curve.
π Example: Given I1=1A at VD=0.65V and I2=2A at VD=0.67V, with VT=25mV:
- Using the equation form, ln(I1) - ln(I2) = (VD1 - VD2) / (nVT). Solving: -ln2 = -0.02 / (n * 0.025) β n = 1.154.
- Substitute n into the equation for I1: Is = I1 * e^(-VD1 / (nVT)) = 1 * e^(-0.65 / (1.154*0.025)) = 1.64 x 10^-10 A.
- For VD=0.7V: I = 1.64 x 10^-10 * e^(0.7 / (1.154*0.025)) = 5.66 A.
THE REVERSE BIAS REGION:
This section explains diode behavior when a negative voltage is applied.
When the diode voltage (v) is negative, the exponential term in the diode equation becomes negligible compared to 1. Therefore, the diode current becomes approximately i = -Is. This constant, small reverse current is called the saturation current. A significant portion of this reverse current is due to leakage effects, which are proportional to the junction area and have a different temperature dependence than Is.
THE BREAKDOWN REGION:
This section describes the diode's behavior under a large reverse voltage.
The breakdown region is entered when the magnitude of the reverse voltage exceeds a specific threshold called the BREAKDOWN VOLTAGE (VZK). This is the voltage at the "knee" of the i-v curve. In this region, the reverse current increases rapidly, but the voltage change is very small. π‘ Why this matters: This property of a nearly constant voltage despite a large current change is used for voltage regulation.
ANALYSIS OF DIODE CIRCUITS:
This section introduces two methods for finding the DC operating point (ID, VD) of a diode in a simple series circuit with a DC source (VDD) and resistor (R). The circuit is governed by two equations:
- Diode Equation: ID = Is * e^(VD / nVT)
- Kirchhoff's Voltage Law (KVL): ID = (VDD β VD) / R (the load line equation)
GRAPHICAL ANALYSIS:
This method solves the circuit by plotting both equations on the same i-v plane.
The exponential diode curve and the straight load line (from KVL) are plotted. The intersection point of the two graphs is called the operating point (Q-point). Its coordinates give the solution for ID and VD.
ITERATIVE ANALYSIS:
This is a numerical method for solving equations (1) and (2) without a graph. A step-by-step example is provided.
π Example: For VDD=5V and R=1kΞ©, the diode has 1mA at 0.7V and changes by 0.1V per decade change in current (2.3nVT=0.1V).
- Iteration 1: Assume VD=0.7V. Then ID = (5-0.7)/1 = 4.3mA. Then VD2 = 0.7 + 0.1 * log(4.3/1) = 0.763V. Result: ID=4.3mA, VD=0.763V.
- Iteration 2: Use VD=0.763V. Then ID = (5-0.763)/1 = 4.237mA. Then VD2 = 0.763 + 0.1*log(4.237/4.3) = 0.762V. Result: ID=4.23mA, VD=0.762V. Since the values from iteration 2 are very close to iteration 1, the solution is ID = 4.23mA and VD = 0.762V.
β Key Takeaways
The most critical concepts from this lecture are the three diode operating regions: forward, reverse, and breakdown. In reverse bias, the current is essentially constant at the saturation current (Is), while in breakdown, the voltage is nearly constant, enabling voltage regulation. For circuit analysis, the exponential diode equation and the load line equation must be solved simultaneously. This can be done graphically by finding the Q-point intersection, or numerically using iterative analysis, which progressively refines the voltage and current estimates until they converge on a stable solution.
π§ Quick Revision Questions
- According to the lecture, what is the approximate current in a diode when it is in the reverse bias region, and why is it called the saturation current?
- How is the breakdown region of a diode used in practical circuit design?
- What are the two equations that must be solved to find the DC operating point (ID, VD) of a diode in a series circuit with a resistor and a DC source?
- In the iterative analysis method, what is the first step, and what starting assumption is typically made?
- For a diode circuit, what does the term "load line" refer to, and what is the significance of the Q-point (operating point)?
π Lecture 33 β (DC or Static Resistance-The constant voltage drop model - AC or Dynamic Resistance)
π Overview: This lecture explores the behavior of diodes under different types of voltage conditions. It covers how to calculate DC or static resistance from the characteristic curve, introduces the constant voltage drop model including ideal and practical models for circuit analysis, and defines AC or dynamic resistance which depends on the operating point. Understanding these models is crucial for analyzing and designing basic diode circuits.
ποΈ Topics Covered
The lecture first defines DC or Static Resistance and demonstrates its calculation at different operating points using a diode's characteristic curve. It then introduces the Constant Voltage Drop Model, explaining the Ideal Model (diode as a switch) and the Practical Model (including a 0.7V forward voltage drop for silicon). Finally, it covers the AC or Dynamic Resistance.
π Lecture Summary
DC OR STATIC RESISTANCE:
When a diode is subjected to a dc voltage, its operating point on the characteristic curve does not change with time. The DC resistance (rD) of the diode can be found easily using Ohm's Law directly from the voltage and current at that point. It may also be observed on the curve that the resistance in the reverse bias region is quite high.
π Definition β DC or Static Resistance (rD): The resistance of a diode when a DC voltage is applied, found by dividing the DC voltage across the diode (VD) by the DC current through it (ID). Formula: rD = VD / ID
π Formula: rD = VD / ID β The static resistance at a specific point on the characteristic curve.
π Example: Determine the resistance level for the diode with the given characteristics at three different points.
- For ID = 1mA: From the curve, VD = 0.5 volts. RD = 0.5V / 1mA = 500 ohms
- For ID = 20mA: From the curve, VD = 0.8 volts. RD = 0.8V / 20mA = 40 ohms
- For VD = -10V: From the curve, ID = -1Β΅A. RD = 10V / 1Β΅A = 10 Mohms
This example shows that a diode's resistance is not constant; it decreases significantly as forward current increases and is very high in reverse bias.
THE CONSTANT VOLTAGE DROP MODEL:
This model uses a vertical straight line to approximate the fast-rising part of the exponential curve of a forward-biased diode. It simplifies analysis by assuming a constant voltage drop across the diode when it is conducting.
Ideal Model: In this model, the diode behaves essentially as a switch: on when forward biased, off when reverse biased. When the diode is reverse biased, we replace it with an open switch, and when it is forward biased, we use a closed switch. This model ignores the forward voltage drop.
Practical Model: In practice, there is a voltage drop of about 0.7 V across a forward-biased silicon diode (0.3 V for germanium). The practical model adds a voltage source representing this drop to the ideal model. The resulting model says that a forward-conducting diode exhibits a constant voltage drop (VD) of 0.7 volts. π‘ Why this matters: This model is a very useful approximation for quick hand calculations of circuits.
The Effect of the Forward Voltage Drop on Circuit Analysis: To illustrate, consider a circuit with a 5V source (Vs), a silicon diode, and a 1-ohm resistor (R1) in series. According to KVL: Vs = VF + VR. Assuming a silicon diode, VF = 0.7V. Therefore, VR = Vs - 0.7V = 5V - 0.7V = 4.3V. The current IT = VR / R1 = 4.3V / 1Ξ© = 4.3A. If the diode were considered ideal (VF=0), the current would be 5V / 1Ξ© = 5A, showing the impact of the 0.7V drop.
π Example: Find the voltage across R1 (VR) in a circuit with a 6V source and a silicon diode in series. Solution: By KVL, Vs = VR + Vf. For a silicon diode, Vf = 0.7V. So, VR = Vs - 0.7V = 6V - 0.7V = 5.3 volts (β5 Volts).
The key rules for the Constant Voltage Drop Model are:
- Diode current remains at zero until the applied voltage reaches the knee voltage (Vk).
- Once the applied voltage reaches Vk, the diode turns on and forward conduction occurs.
- As long as the diode is conducting, the forward voltage (VF) is assumed to be a constant 0.7 volts, regardless of the value of the forward current (IF).
AC OR DYNAMIC RESISTANCE:
The AC or dynamic resistance (rD) of a diode describes its resistance to small changes (as in an AC signal) in voltage and current. It is defined as the ratio of a small change in voltage to the corresponding small change in current around a specific operating point.
π Definition β AC or Dynamic Resistance (rD): The resistance offered by a diode to a varying (AC) signal, calculated as the change in voltage divided by the change in current at a specific Q-point.
π Formula: rD = ΞvD / ΞiD β where Ξ (delta) indicates a finite (small) change in the quantity.
The resistance in the vertical rise region of the forward bias curve is small, whereas the AC resistance is much larger at low current levels.
β Key Takeaways
A diode has three distinct types of resistance. DC resistance is found by dividing the DC voltage by the DC current (V/I) at a single point on the curve, and it changes based on the operating point. The Constant Voltage Drop Model simplifies circuit analysis by assuming a forward-biased silicon diode has a fixed 0.7V drop, with the ideal model treating it as a simple switch. AC or dynamic resistance is the slope of the characteristic curve (ΞV/ΞI) and is used for analyzing small signal variations. For the exam, be prepared to calculate static resistance from a graph, solve circuits using the constant voltage drop model, and define dynamic resistance.
π§ Quick Revision Questions
- What is the formula for calculating the DC or static resistance of a diode?
- A silicon diode conducts a current of 15mA when the voltage across it is 0.75V. What is its static resistance?
- In the constant voltage drop model, what is the assumed forward voltage drop for a silicon diode?
- How does the practical model of a diode differ from the ideal model when the diode is forward biased?
- What does the 'Ξ' in the formula rD = ΞvD / ΞiD signify?
π Lecture 34 β Small Signal Model and its applications
π Overview: This lecture introduces the small signal model for diodes, which is essential for analyzing circuits where a small AC signal is superimposed on a DC bias. It explains how to calculate AC resistance, the small signal model derivation, and its practical applications in circuit analysis and design.
ποΈ Topics Covered
The lecture covers AC resistance calculation from diode characteristic curves, the derivation of the small signal model using Taylor series expansion, the concept of small signal conductance and resistance, DC and AC analysis separation in circuits, and several application examples including the straight-line approximation and circuit design with multiple diodes.
π Lecture Summary
EXAMPLE: Find the AC resistance for the curve shown at (1) ID = 2mA (2) ID = 25mA
Solution (1): For ID = 2mA, choose a swing of plus minus 2mA. When ID = 4mA, VD = 0.76V; when ID = 0mA, VD = 0.65V.
- βID = 4 - 0 = 4mA
- βVD = 0.76 - 0.65 = 0.11V
- rD = βVD/βID = 0.11/4m = 27.5 ohms
Solution (2): For ID = 25mA, choose a swing of plus minus 5mA.
- βI = 30 - 20 = 10mA
- βVD = 0.8 - 0.78 = 0.02V
- rD = 0.02/10 = 10 ohms
SMALL SIGNAL MODEL
In some applications, a circuit is supplied with a bias to operate in the forward region, and a small AC signal is superimposed on the DC quantity. When there is no AC, diode voltage is VD so that I = ISe^(VD/nVT). When signal vd(t) is applied, the instantaneous voltage vD(t) = VD + vd(t), and the instantaneous diode current becomes iD(t) = ISe^((VD+vd)/nVT) = IDe^(vd/nVT) β Equation (A).
If the amplitude of the signal is sufficiently smaller than 1, so that Vd/nVT << 1, we expand using the Taylor series: e^x = 1 + x/1! + xΒ²/2! + ... Here x = Vd/nVT, so up to two terms: e^(vd/nVT) = (1 + vd/nVT). Substituting into equation (A): iD(t) = ID(1 + vd/nVT) = ID + (ID/nVT)vd β Equation (B). Let (ID/nVT)vd = id, so iD = ID + id.
π Definition β Small Signal Conductance: The quantity ID/nVT has the dimensions of conductance (mhos) and is called the diode small signal conductance. Its inverse is the small signal resistance or incremental resistance given by rd = nVT/ID. Therefore, rd β 1/ID, where n and VT are constants provided by the manufacturer.
APPLICATION: rd = nVT/ID
Consider a circuit with a DC source VDD and an AC source. For analysis, split the circuit into two parts: DC and AC.
For DC analysis: Replace the AC source with a short and use the constant drop model for the diode. The ideal diode is forward biased (short circuit). From KVL: VDD - IDR - VDo - IDrd = 0. Therefore: VDD = IDR + VDo + IDrd β Equation (A).
For AC analysis: Remove all DC sources and the ideal diode. The circuit becomes: vs = id(R + rd) β Equation (B).
Overall analysis combines (A) and (B): VDD + vs = ID(R + rd) + id(R + rd) + VDo = (R + rd)(ID + id) + VDo β Equation (C). Since ID + id = iD, this separates into: VDD = IDR + VDo (DC) and vs = id(R + rd) (AC).
π‘ Why this matters: The AC equation circuit is simply a voltage divider. Hence the diode signal voltage is Vd = Vs Γ rd/(rd + R).
EXAMPLE: Find the value of the diode small signal resistance rd at bias current of 0.1, 1 and 10mA. Assume n = 1.
Solution: rd = nVT/ID, where VT = 25mV.
- For ID = 0.1mA: rd = 250 ohms
- For ID = 1mA: rd = 25 ohms
- For ID = 10mA: rd = 2.5 ohms
EXAMPLE: For a diode that conducts 1mA at a forward voltage drop of 0.7V and n = 1, find the equation of the straight line tangent at ID = 1mA.
Solution: Slope = 1/rd = ID/nVT = 1mA/(1Γ25mV) = 1/25 ohms. On the VD axis, the intercept = 0.7 - 1m(25) = 0.7 - 0.025 = 0.675V. Using the equation of a straight line y - yβ = m(x - xβ): iD = (1/25)(VD - 0.675). Therefore, VD - 0.675 - iD(25) = 0, which is the required equation.
EXAMPLE: Consider a diode with n = 2 biased at 1mA. Find the change in current for voltage changes of -20mV, -10mV, -5mV, +5mV, +10mV, +20mV using (1) small signal model and (2) exponential model.
Solution: For small signal model: βv = rdβi, so βi = βv/rd. rd = nVT/ID = 2Γ25m/1m = 50 ohms. Thus βi = βv/50. For exponential model: i = ISe^(v/nVT). Since ID + βi = IDe^(βv/nVT), we get βi = ID(e^(βv/nVT) - 1). With ID = 1mA: βi = e^(βv/nVT) - 1.
- (a) βv = -20mV: (1) βi = -20/50 = -0.4mA; (2) βi = e^(-20/50) - 1 = -0.33mA
- (d) βv = +5mV: (1) βi = 5/50 = 0.10mA; (2) βi = e^(5/50) - 1 = 0.11mA
- (f) βv = +20mV: (1) βi = 20/50 = 0.40mA; (2) βi = e^(20/50) - 1 = 0.49mA
EXAMPLE: Design the circuit so that Vβ = 3V when I_L = 0, and Vβ changes by 40mV per 1mA of load current. Find R. Assume four identical diodes with 0.7V drop at 1mA current and n = 1.
Solution: When Vβ = 3V and I_L = 0, each diode exhibits a drop of 0.75V. When I_L = 1mA, Vβ changes by 40mV, so change per diode is 10mV. Thus rd = 10mV/1mA = 10 ohms. Using rd = nVT/ID: 10 = 1Γ25m/ID, so ID = 2.5mA. From 15 - 3 - IDR = 0: R = (15 - 3)/2.5m = 4.8k Ohms.
β Key Takeaways
The small signal resistance of a diode is given by rd = nVT/ID and is inversely proportional to the bias current, meaning higher bias currents produce lower AC resistance. The small signal model allows superposition analysis by separating DC and AC components, where the AC equivalent circuit is simply a voltage divider with the diode appearing as a resistor rd. For accurate small-signal analysis, the AC signal amplitude must be much smaller than nVT (typically less than 5mV for n=1). The exponential model gives more accurate results than the small signal model for larger voltage swings, but the small signal model provides a good linear approximation for small perturbations.
π§ Quick Revision Questions
- What is the formula for AC resistance (rD) of a diode, and how is it calculated from the characteristic curve?
- Derive the small signal model equation iD = ID + id starting from the exponential diode equation.
- For a diode with n=1 biased at 2mA, what is the small signal resistance rd?
- In the overall analysis combining DC and AC, write the KVL equation for each component separately.
- Why does the small signal model become inaccurate for large AC signal amplitudes?
π Lecture 35 β Transformers - Secondary voltage and current - Transformer Input/Output phase relationship
π Overview: This lecture introduces the transformer, a fundamental non-semiconductor device essential in power supplies. It covers the basic structure, types (step-up, step-down, isolation), and key calculations for secondary voltage and current using the turn ratio. The lecture also explains the input/output phase relationship in transformers and concludes with an introduction to half-wave rectifiers.
ποΈ Topics Covered
The lecture begins by defining the transformer's structure with primary and secondary windings and its schematic symbol. It then details three transformer modes: step-up, step-down, and isolation. The key concept of turn ratio is introduced, along with formulas for calculating secondary voltage and secondary current based on this ratio. The transformer's input/output phase relationship is explained using dot notation. Finally, the lecture covers half-wave rectifiers, including both positive and negative configurations, which use diodes and resistors to eliminate parts of an AC signal.
π Lecture Summary
TRANSFORMERS
Transformers are not semiconductor devices but are integral to most power supplies. The basic schematic symbol shows two coil-like windings. The transformer consists of two inductors in close proximity but not physically connected. The two windings are called the primary (input) and secondary (output). An alternating voltage applied to the primary induces an alternating voltage in the secondary. The primary and secondary are physically isolated. A transformer can be designed in three modes:
- STEP UP TRANSFORMER: Provides a secondary voltage greater than the primary voltage (e.g., 240 Vac output from 120 Vac input).
- STEP DOWN TRANSFORMER: Provides a secondary voltage less than the primary voltage (e.g., 30 Vac output from 120 Vac input).
- ISOLATION TRANSFORMER: Provides an output voltage equal to the input voltage, used to electrically isolate power supplies from power lines.
TURN RATIO
The turn ratio of a transformer is the ratio of the number of turns in the primary to the number of turns in the secondary. For example, a 4:1 ratio means four turns in the primary for every one turn in the secondary. The turn ratio is equal to the voltage ratio of the two windings.
π Turn Ratio Formula: The relationship is defined as: ( \frac{V_2}{V_1} = \frac{N_2}{N_1} ) Where:
- ( N_2 ) = number of turns in the secondary winding
- ( N_1 ) = number of turns in the primary winding
- ( V_2 ) = voltage in the secondary
- ( V_1 ) = voltage applied to the primary
π Formula for Calculating Secondary Voltage: ( V_2 = \left( \frac{N_2}{N_1} \right) V_1 )
π Example: For a step-down transformer with a 4:1 turn ratio and a ( V_1 ) of 120 Vac: ( V_2 = \left( \frac{1}{4} \right) \times 120Vac = 30Vac )
CALCULATING SECONDARY CURRENT
Ideally, transformers are 100% efficient, meaning input power equals output power (( P_2 = P_1 )). Since power is the product of voltage and current, we can write: ( V_2 I_2 = V_1 I_1 ) This leads to: ( \frac{I_1}{I_2} = \frac{V_2}{V_1} ) The current ratio is the inverse of the voltage ratio. This implies:
- For a step-down transformer, ( I_2 > I_1 ) (current increases).
- For a step-up transformer, ( I_2 < I_1 ) (current decreases).
Since the voltage ratio equals the turn ratio, we can also write: ( \frac{I_1}{I_2} = \frac{N_2}{N_1} ) Therefore: ( I_2 = \left( \frac{N_1}{N_2} \right) I_1 )
π Example: A fuse limits the primary current ( ( I_1 ) ) to 1A. What is the limit on the secondary current for a transformer with a turn ratio of 4:1? ( I_2 = \left( \frac{N_1}{N_2} \right) I_1 = \left( \frac{1}{4} \right) \times 1A = 250mA ) If the secondary current tries to exceed 250mA, the primary current will exceed 1A and blow the fuse.
TRANSFORMER INPUT/OUTPUT PHASE RELATIONSHIP
The phase relationship between the primary and secondary voltages is indicated by dots on the schematic symbol.
- If the dots are on the same side (e.g., top of primary and top of secondary), the output voltage is in phase with the input voltage.
- If the dots are on opposite sides (e.g., top of primary and bottom of secondary), the output voltage is 180Β° out of phase with the input voltage.
HALF WAVE RECTIFIERS
A half-wave rectifier is made up of a diode and a resistor and is used to eliminate either the positive or negative part of the input AC signal.
- Positive Half Wave Rectifier: The diode conducts during the positive half-cycle of the input, producing an output voltage across the load resistor. It is reverse-biased during the negative half-cycle.
- Negative Half Wave Rectifiers: The diode direction is reversed. The diode conducts on the negative half-cycle of the input, and the load voltage equals the secondary voltage. The positive half-cycle of the input is eliminated. The operating principle is the same as the positive half-wave rectifier, with the only difference being the polarity of the output will be reversed.
β Key Takeaways
The transformer is a non-semiconductor device consisting of primary and secondary windings that are physically isolated. Its core function is to transfer energy through electromagnetic induction. The turn ratio ( ( N_2/N_1 ) ) is the fundamental parameter, dictating that the voltage ratio is directly proportional to it ( ( V_2/V_1 = N_2/N_1 ) ), while the current ratio is inversely proportional ( ( I_1/I_2 = N_2/N_1 ) ). The typesβstep-up, step-down, and isolationβdetermine whether output voltage is higher, lower, or equal to the input. The dot notation on the schematic indicates whether the secondary voltage is in phase or 180Β° out of phase with the primary. The half-wave rectifier, a simple circuit using a single diode and resistor, serves to block one half of an AC waveform, resulting in a pulsating DC output.
π§ Quick Revision Questions
- What is the fundamental difference between a step-up and a step-down transformer?
- Write the formula that relates the primary and secondary voltages to the number of turns in the windings.
- For an ideal transformer with a turn ratio of 10:1 (primary:secondary) and a primary voltage of 120V, what is the secondary voltage? What type of transformer is this?
- If the secondary current in a step-down transformer is 2A, and the turn ratio is 1:5 (primary:secondary), what is the primary current?
- Explain what the two dots on a transformer's schematic symbol indicate.
π Lecture 36 β Half Wave Rectifiers
π Overview: This lecture covers negative half wave rectifiers and provides general rules for determining output polarity based on diode orientation. It then focuses on the critical calculations for load voltage, load current, and average (DC) values in half wave rectifier circuits, including the use of transformer turns ratios and RMS-to-peak conversions.
ποΈ Topics Covered
The lecture begins with negative half wave rectifiers and general polarity rules based on diode direction. It then moves into calculating peak load voltage using transformer turns ratios and RMS-to-peak conversions, demonstrated through multiple examples. Next, it covers calculating peak load current, followed by determining average load voltage and current using the 1/Ο (0.318) conversion factor.
π Lecture Summary
Negative Half Wave Rectifiers
When the diode direction is reversed in a half wave rectifier, the diode conducts on the negative half cycle of the input. During this time, ( V_L = V_2 ). The diode is reverse biased during the positive half cycle, and ( V_D = V_2 ), eliminating the positive half cycle. The operating principle is the same as positive half wave rectifiers; the only difference is the output polarity is reversed.
General Rules for Polarity
Two general rules determine the output polarity of a half wave rectifier:
π Rule 1: When the diode points towards the load (R_L), the output from the rectifier will be positive.
π Rule 2: When the diode points towards the transformer, the output from the rectifier will be negative.
Calculating Load Voltage and Current Values
The load voltage in a half wave rectifier is found as:
π Formula: ( V_{L(pk)} = V_{2(pk)} - V_F ) β The peak load voltage equals the peak secondary voltage minus the diode forward voltage drop (typically 0.7V for silicon).
The peak secondary voltage is determined by the transformer turns ratio:
π Formula: ( V_{2(pk)} = \frac{N_2}{N_1} \times V_{1(pk)} ) β The peak secondary voltage equals the turns ratio multiplied by the peak primary voltage.
When source voltages are given as RMS values, they are converted to peak values:
π Formula: ( V_{pk} = \frac{V_{rms}}{0.707} ) β Peak voltage equals RMS voltage divided by 0.707.
π Example 1: For a circuit with 120V RMS primary, turns ratio 1/5, and silicon diode:
- ( V_{1(pk)} = 120 / 0.707 = 169.7V_{pk} )
- ( V_{2(pk)} = (1/5)(169.7) = 33.94V_{pk} )
- ( V_{L(pk)} = 33.94 - 0.7 = 33.24V_{pk} )
π Example 2: For a circuit with 25V AC secondary rating:
- ( V_{2(pk)} = 25 / 0.707 = 35.36V_{pk} )
- ( V_{L(pk)} = 35.36 - 0.7 = 34.66V_{pk} )
Calculating Load Current
Once the peak voltage is determined, the peak load current is found using Ohm's law:
π Formula: ( I_{L(pk)} = \frac{V_{L(pk)}}{R_L} ) β Peak load current equals peak load voltage divided by load resistance.
π Example: For a circuit with 200V RMS primary, turns ratio 1/5, load resistance 10kΞ©:
- ( V_{1(pk)} = 200 / 0.707 = 282.9V_{pk} )
- ( V_{2(pk)} = (1/5)(282.9) = 56.6V_{pk} )
- ( V_{L(pk)} = 56.6 - 0.7 = 55.9V_{pk} )
- ( I_{L(pk)} = 55.9V / 10kΞ© = 5.59mA_{pk} )
Average Load Voltage and Current
Since rectifiers are used to convert AC to DC, the average (DC) voltage ( V_{ave} ) is a very important value. For a half wave rectifier:
π Formula: ( V_{ave} = \frac{V_{pk}}{\pi} ) or ( V_{ave} = 0.318(V_{pk}) ) β The average DC voltage equals the peak voltage divided by Ο (approximately 0.318 times peak voltage).
π‘ Why this matters: This is the DC equivalent value that would be measured by a DC voltmeter at the output of a half wave rectifier.
π Example: For a circuit with 75V RMS primary and turns ratio 1/2:
- ( V_{1(pk)} = 75 / 0.707 = 106.1V_{pk} )
- ( V_{2(pk)} = (1/2)(106.1) = 53.04V_{pk} )
- ( V_{L(pk)} = 53.04 - 0.7 = 52.34V_{pk} )
- ( V_{ave} = 52.34 / \pi = 16.66V_{dc} )
Calculating Average Current
The average (DC) load current ( I_{ave} ) can be calculated in two ways:
Method 1: Determine ( V_{ave} ) first, then use Ohm's law: π ( I_{ave} = \frac{V_{ave}}{R_L} )
Method 2: Convert from peak current using the same conversion: π ( I_{ave} = \frac{I_{pk}}{\pi} ) or ( I_{ave} = 0.318(I_{pk}) )
π Example: For a circuit with 24V AC secondary rating and 20kΞ© load:
- ( V_{2(pk)} = 24 / 0.707 = 33.9V_{pk} )
- ( V_{L(pk)} = 33.9 - 0.7 = 33.2V_{pk} )
- ( I_{L(pk)} = 33.2 / 20kΞ© = 1.66mA_{pk} )
- ( I_{ave} = 1.66mA / \pi = 529.13 \mu A )
β Key Takeaways
The most critical concepts from this lecture are: diode direction determines output polarityβpointing toward the load gives positive output, pointing toward the transformer gives negative output. The peak load voltage subtracts the diode forward drop (0.7V for silicon) from the peak secondary voltage. Always convert RMS values to peak by dividing by 0.707 before using them in calculations. The average (DC) value for a half wave rectifier is the peak value divided by Ο (or multiplied by 0.318), which represents the DC equivalent of the rectified waveform. This average value can be calculated for both voltage and current using the same conversion factor.
π§ Quick Revision Questions
- What is the general rule for determining output polarity based on diode orientation in a half wave rectifier?
- How do you calculate the peak secondary voltage given the RMS primary voltage and transformer turns ratio?
- What is the formula for average (DC) voltage in a half wave rectifier, and what is the numerical constant used?
- In the example with 200V RMS primary, 1/5 turns ratio, and 10kΞ© load, what are the peak load voltage and peak load current?
- What are the two methods for calculating average (DC) load current in a half wave rectifier?