📘 Lecture 24 — Source Transformation and examples
📖 Overview: This lecture explains the technique of source transformation, which allows engineers to simplify complex circuits by converting between voltage sources and current sources. Mastering this method enables easier calculation of voltages and currents in resistive networks.
🗂️ Topics Covered
The lecture covers the fundamental concept of source transformation, including the equivalence between a current source in parallel with a resistance and a voltage source in series with the same resistance. Multiple worked examples demonstrate step-by-step how to apply source transformation to calculate output voltage Vo and current I in various circuits.
📝 Lecture Summary
Source Transformation:
If we have any source embedded within a network, say this source is a current source having a value I and there exists a resistance having a value R, in parallel to it, we can replace it with a voltage source of value V=IR in series with the same resistance R. The reverse is also true: a voltage source V, in series with a resistance R can be replaced by a current source having a value I= V/R in parallel to the resistance R. Parameters within the circuit, for example an output voltage, remain unchanged under these transformations.
💡 Why this matters: Source transformation preserves the external behavior of the circuit while simplifying the internal structure, making analysis much easier.
Example 1: Calculate the voltage Vo using source transformation method.
Solution: We proceed as follows:
1k is in series with 2k so the combined effect is 3k. Now the 2mA source is in parallel with the 3k resistor. So it can be changed to a voltage source of value = 2m x 3k (by Ohm's Law) = 6 Volts. The 3k resistor will become in series with this source.
Positive terminal of the 6 volts battery is connected with the negative terminal of the 3 volts battery, so they will be summed up.
Applying voltage division rule:
🔑 Definition — Voltage Division Rule: The voltage across a resistor in a series circuit is proportional to its resistance relative to the total resistance.
📐 Formula: V_R1 = (R1 / (R1 + R2)) × V_total
Vo = (6 × 9) / 9 = 6 Volts
Example 2: Calculate the voltage Vo using source transformation method.
Solution: We proceed as follows:
3k is in series with 12 volts battery. So it can be converted into a current source of value = 12/3k (by Ohm's Law) = 4mA. Now the voltage source has transformed into the current source.
Now 3k resistor is in parallel with 6k resistor: 3k || 6k = (3k × 6k) / (3k + 6k) = 2k.
We replace 3k and 6k with 2k. The 4mA source is parallel with 2k resistor, so it can be converted into a voltage source. By Ohm's Law, the value is 8 volts in series with a resistor of 2k.
In the circuit, 2k is in series with 2k, so modified circuit becomes 8V source in series with 4k. This can be converted into a current source of value = 8/4k = 2mA in parallel with 4k.
Two current sources are parallel to each other, so they add up to give 4mA. The 4mA source is in parallel with 4k resistor, so it can be converted into a voltage source of value 16 volts.
4k and 4k are in series, so applying voltage division rule:
Vo = (8k / 16k) × 16V = 8 volts
Example 3: Calculate the voltage Vo using source transformation method.
Solution: We proceed as follows:
12 volt source is in series with 3k resistor. So it can be converted into a current source of value I = 12/3k = 4mA (by Ohm's Law). In the modified circuit, the 4mA current source and the 3k resistor will be in parallel.
We combine current sources: 4m – 2m = 2mA. The 2mA source is in parallel with 3k, so it can be converted into a voltage source of value V = 2 × 3 = 6 volts.
3k is in series with 4k, so modified circuit has a 6V source with 7k total resistance. Applying voltage division rule:
🔑 Definition — Voltage Division Rule: The voltage across a specific resistor in a series circuit equals that resistor's fraction of the total resistance times the total voltage.
Vo = (2k / 9k) × 6 = 12/9 = 4/3 volts
Example 4: Calculate the current I using source transformation method.
Solution: We proceed as follows:
3 Ohms resistor is in parallel with 5A source, so it can be converted into a voltage source of 15V. The 3 Ohms and 4 Ohms resistors are in series, and the resultant is in series with 15V, so it can be converted into a current source.
7 || 7 = (7 × 7) / (7 + 7) = 49/14 = 3.5 ohms. The current source is in parallel with 3.5 ohms resistance, so it can be converted into a voltage source by Ohm's Law: V = IR = (15/7) × 3.5 = 7.5 Volts.
The current I can be found using KVL:
-7.5 + 3.5I – 51V_x + 28I + 9 = 0 -------------------- (A)
Where V_x = 2I
Putting the value of V_x in (A):
-7.5 + 3.5I - 51(2I) + 28I + 9 = 0 3.5I - 102I + 28I + 1.5 = 0 -70.5I + 1.5 = 0
I = 1.5 / 70.5 = 21.28 mA
⭐ Key Takeaways
Source transformation is a powerful circuit simplification technique where a current source in parallel with a resistor can be replaced by a voltage source in series with the same resistor (V=IR), and vice versa (I=V/R). This method preserves all external circuit parameters and is particularly useful when combined with series/parallel resistance calculations and voltage/current division. When multiple sources exist, they can be transformed sequentially to reach a simple series or parallel circuit where Ohm's Law or voltage division can be applied directly. The key is to always maintain the correct polarity and direction during transformations.
🧠 Quick Revision Questions
- What is the voltage source equivalent of a 5mA current source in parallel with a 2kΩ resistor?
- In Example 1, why do the 6V and 3V sources add rather than subtract?
- What is the combined resistance of 3kΩ and 6kΩ in parallel?
- In Example 4, how is the voltage Vx related to the current I?
- Can source transformation be applied to sources that are not in the standard parallel or series configuration?
📘 Lecture 25 — (Thevenin's Theorem)
📖 Overview: This lecture introduces Thevenin's Theorem, a powerful circuit analysis technique that simplifies complex circuits into an equivalent voltage source and series resistance. It provides a systematic four-step method for calculating unknown voltages, currents, or power across any load resistor, making circuit analysis more efficient and manageable.
🗂️ Topics Covered
The lecture presents Thevenin's Theorem with its four-step problem-solving procedure, followed by three detailed numerical examples demonstrating how to calculate the Thevenin equivalent voltage (Vth) and Thevenin equivalent resistance (Rth) for various circuits. Each example applies the theorem to find the voltage across a load resistor (Vo) in circuits containing resistors, voltage sources, and current sources.
📝 Lecture Summary
THEVENIN'S THEOREM
Thevenin's Theorem states that any linear two-terminal circuit can be replaced by an equivalent circuit consisting of a voltage source (Vth) in series with a resistor (Rth). The four-step procedure is:
Step 1: Remove the load resistor (the resistor across which you want to find voltage, current, or power), leaving behind an open circuit.
Step 2: Calculate the Thevenin voltage (Vth) across the open terminals by any method (e.g., mesh analysis, nodal analysis, voltage division, superposition).
Step 3: Calculate the Thevenin resistance (Rth) by open-circuiting all current sources and short-circuiting all voltage sources, then finding the total resistance seen from the open terminals.
Step 4: Re-insert the load resistance (RL) in series with Rth and Vth (treating Vth as a battery), then calculate the desired quantity using simple series circuit formulas.
💡 Why this matters: This theorem allows you to analyze any one branch of a complex circuit without solving the entire circuit each time.
🔑 Definition — Thevenin Voltage (Vth): The voltage across the open terminals when the load resistor is removed from the circuit. 🔑 Definition — Thevenin Resistance (Rth): The equivalent resistance seen from the open terminals with all independent voltage sources short-circuited and all independent current sources open-circuited.
EXAMPLE 1: Calculating Vo using Thevenin's Theorem
Circuit Details: Contains a 6V voltage source, 2mA current source, resistors of 1kΩ, 2kΩ, 3kΩ, and a 6kΩ load resistor.
First step: Removing RL. Here RL is the 6kΩ resistor at which we want to calculate the voltage Vo.
Second step: Calculating Vth. 1kΩ is in series with 2kΩ, so modified circuit has 3kΩ in parallel with 2mA source. By source transformation, the 2mA source in parallel with 3kΩ becomes a voltage source. V = 2mA × 3kΩ (by Ohm's Law) = 6 Volts. The 3kΩ resistor becomes in series with this source. The combined effect of the two sources (6V original and 6V transformed) is 9 volts.
📐 Formula: V = I × R → voltage from source transformation 📌 Example: 2mA × 3kΩ = (2 × 10⁻³) × (3 × 10³) = 6V
Third step: Calculating Rth. Vth = 9 volts Rth = 3kΩ
Fourth step: Calculating the unknown quantity. Re-inserting RL = 6kΩ in series with Rth = 3kΩ and Vth = 9V.
📐 Formula: Voltage division → Vo = (RL / (Rth + RL)) × Vth 📌 Example: Vo = (6kΩ / (3kΩ + 6kΩ)) × 9 = (6k/9k) × 9 = 6 volts
EXAMPLE 2: Calculating Vo using Thevenin's Theorem (with Superposition)
Circuit Details: Contains a 12V voltage source, 2mA current source, resistors of 2kΩ, 3kΩ, 4kΩ, 6kΩ, and an 8kΩ load resistor.
First step: Removing RL. Here RL is the 8kΩ resistor at which we want to calculate Vo.
Second step: Calculating Vth using superposition method.
Only voltage source acting: No current in 'CA' branch, so voltage drop across 4kΩ and 2kΩ resistor is zero. Vth1 = VCD Applying voltage division rule: Vth1 = V6k = (12 × 6) / (3 + 6) = 8 volts
📌 Example: Vth1 = (12V × 6kΩ) / (3kΩ + 6kΩ) = 72/9 = 8V
Only current source acting: 3kΩ || 6kΩ = (3kΩ × 6kΩ) / (3kΩ + 6kΩ) = 2kΩ 2kΩ is in series with 2kΩ = 4kΩ Current through open circuit is zero by Ohm's Law. Vth2 = 4kΩ × 2mA = 8 volts
📌 Example: Vth2 = (4 × 10³) × (2 × 10⁻³) = 8V
Total Vth = Vth1 + Vth2 = 8 + 8 = 16 volts
Third step: Calculating Rth. 3kΩ || 6kΩ = (3kΩ × 6kΩ) / 9kΩ = 2kΩ Rth = 2kΩ + 2kΩ + 4kΩ = 8kΩ
Fourth step: Calculating unknown quantity. Re-inserting RL = 8kΩ in series with Rth = 8kΩ and Vth = 16V.
📌 Example: Vo = (8kΩ / (8kΩ + 8kΩ)) × 16 = (8k/16k) × 16 = 8 volts
EXAMPLE 3: Calculating Vo using Thevenin's Theorem (with KVL)
Circuit Details: Contains a 6V voltage source, 2mA current source, resistors of 2kΩ (two), 4kΩ, and a 6kΩ load resistor.
First step: Removing RL. Here RL is the 6kΩ resistor at which we want to calculate Vo.
Second step: Calculating Vth using KVL (Kirchhoff's Voltage Law).
Given: I2 = 2mA For loop 1: 4kΩ(I1) + 2kΩ(I1 - I2) = 6 4kΩ(I1) + 2kΩ(I1) - 2kΩ(I2) = 6 6kΩ(I1) - 2kΩ(I2) = 6 Substituting I2 = 2mA: 6kΩ(I1) - 4 = 6 I1 = 10/6kΩ = 1.6mA
Voltage across 4kΩ resistor: V4k = 1.6mA × 4kΩ = 20/3 = 6.66 volts Voltage across 2kΩ resistor: V2k = 2mA × 2kΩ = 4 volts
📌 Example: Vth = V4k + V2k = 20/3 + 4 = 6.66 + 4 = 10.66 volts
Third step: Calculating Rth. 4kΩ || 2kΩ = (4kΩ × 2kΩ) / 6kΩ = 8/6 kΩ = 4/3 kΩ = 1.33 kΩ These are in series, so: Rth = 1.33kΩ + 2kΩ = 10/3 kΩ = 3.33kΩ
Fourth step: Calculating unknown quantity. Re-inserting RL = 6kΩ in series with Rth = 10/3 kΩ and Vth = 32/3 V.
📌 Example: Vo = 32/3 × 6 × 1/(10/3 + 6) = 64 × 3/(10 + 18) = 192/28 = 48/7 volts
⭐ Key Takeaways
Thevenin's Theorem provides a powerful method to simplify complex circuits by replacing everything except the load resistor with an equivalent voltage source (Vth) and series resistance (Rth). The four-step procedure must be followed strictly: remove the load, calculate Vth using any circuit analysis method, calculate Rth by deactivating all independent sources, then re-insert the load and use simple series circuit calculations. Vth can be found using voltage division, superposition, KVL, or source transformation, while Rth requires shorting voltage sources and opening current sources. The final calculation always uses the voltage divider formula Vo = (RL/(Rth+RL)) × Vth for voltage across the load resistor.
🧠 Quick Revision Questions
- What are the four steps of Thevenin's Theorem procedure?
- How do you calculate Thevenin resistance (Rth) when finding the equivalent resistance?
- In Example 2, why was superposition used to find Vth, and what were the individual contributions?
- In Example 3, how was KVL applied to find the currents and voltages needed for Vth?
- What is the formula for calculating the voltage across the load resistor once Vth and Rth are known?
📘 Lecture 26 — Examples of Thevenin’s Theorem - Thevenin’s Theorem and Dependent sources with examples
📖 Overview: This lecture demonstrates the practical application of Thevenin’s Theorem through multiple numerical examples. It also explains the modified procedure for applying Thevenin’s Theorem to circuits containing dependent sources. Understanding these examples is crucial for solving complex circuit analysis problems and for maximum power transfer calculations.
🗂️ Topics Covered
The lecture covers three detailed examples of Thevenin’s Theorem applied to resistive circuits with independent sources, followed by a dedicated example demonstrating the special technique required when the circuit contains dependent sources. Each example follows the systematic four-step procedure: removing the load, calculating Vth, calculating Rth, and finding the unknown quantity.
📝 Lecture Summary
Example 1: Calculating Voltage V₀ using Thevenin’s Theorem
First step: Removing RL The load resistor RL is the 4kΩ resistor across which voltage V₀ is to be calculated. This resistor is removed from the circuit.
Second step: Calculating Vth We want to calculate Vth. Apply KVL in two loops to calculate the individual loop currents. Here I₁ = 2mA
KVL for the super mesh: -6 + 6kI₂ + 12k(I₂ + I₁) + 12k(I₂ + I₁) = 0 -6 + 6kI₂ + 12kI₂ + 12kI₂ + 24kI₁ = 0 30kI₂ – 6 + 24k(2m) = 0 30kI₂ – 6 + 48 = 0 I₂ = -42/30mA I₂ = -1.4mA
Now we calculate the voltage across 6k and 12k to find Vth. V₆ₖ = 6kI₂ = 6k(-1.4m) = -8.4 volts V₁₂ₖ = 12k(I₁ + I₂) = 12k(2m – 1.4m) = 7.2 volts Vth = V₆ₖ + V₁₂ₖ = -8.4 + 7.2 🔑 Vth = -1.2 volts
Third step: Calculating Rth 6k is in series with 12k. The resultant is in parallel with 12k. (6k+12k) || 12k = 18k x 12k / (12k + 18k) 🔑 Rth = 7.2kΩ
Fourth step: Calculating the unknown quantity After calculating Vth and Rth, re-insert the load resistance RL in series with Rth, with Vth as a battery. V₀ = -1.2 x 4k / (7.2k + 4k) 📐 V₀ = -0.4285 volts
Example 2: Calculating RL and Maximum Power Dissipation
First step: Removing RL In this case, RL is the load resistor. Remove it to calculate Vth.
Second step: Calculating Vth Here I₁ = 2mA
Applying KVL to loop 2: 6kI₂ + 3k(I₂ – I₁) + 3 = 0 9kI₂ – 3kI₁ + 3 = 0 9kI₂ – 6 + 3 = 0 I₂ = 1/3 mA = 0.33mA
Calculate voltages: VAB = 4k(I₁) = 4k(2m) = 8 volts VBC = 6k(I₂) = 6k x 0.33m = 2 volts Vth = VAB + VBC = 8 + 2 🔑 Vth = 10 volts
Third step: Calculating Rth Short circuit the voltage source and open circuit the current source. 3k is in parallel with 6k, and 4k is in series with the result. 3k || 6k + 4k = (3k x 6k)/(3k+6k) + 4k = 2k + 4k = 6k 🔑 Rth = RL = 6kΩ
Fourth step: Calculating unknown quantity For maximum power dissipation: RL = Rth = 6k P = I²R From Ohm’s law I = V/R = 10/(6k+6k) = 10/12k P = (10/12k)² x 6k = (0.83)² x 6 📐 PL = 4.1 mW 💡 Why this matters: Maximum power transfer occurs when the load resistance equals the Thevenin resistance.
Example 3: Calculating RL and Maximum Power Dissipation (Second Circuit)
First step: Removing RL Remove the load resistor RL.
Second step: Calculating Vth Apply KVL to the circuit.
For loop 1: -12 + 6I₁ + 6(I₁ – I₂) = 0 -12 + 12I₁ – 6I₂ = 0 2I₁ – I₂ = 2 —————— (A)
For loop 2: 12I₂ – 6I₁ + 3 = 0 4I₂ – 2I₁ + 1 = 0 2I₁ = 4I₂ + 1
Putting in equation (A): 4I₂ + 1 – I₂ = 2 3I₂ = 1 I₂ = 0.33mA
From equation (A): I₁ = (I₂ + 2)/2 = (0.33 + 2)/2 I₁ = 1.166mA
Voltage across 6k resistor: V₆ₖ = 6kI₁ = 6k(1.166m) = 7 volts Vth = 7V + 3V 🔑 Vth = 10 volts
Third step: Calculating Rth 6k is in parallel with 6k. The result is in parallel with a third 6k resistor. 6k || 6k = (6k x 6k)/(6k + 6k) = 3k 3k || 6k = (6k x 3k)/(6k + 3k) = 2k 🔑 Rth = RL = 2kΩ
Fourth step: Calculating unknown quantity VRL = 10 x 2k / (2k + 2k) = 5 volts
To calculate power dissipation: P = V²/R = 25/2k 📐 PL = 12.5 mW
THEVENIN’S THEOREM AND DEPENDENT SOURCES
Working with dependent sources is different from working with independent sources while applying Thevenin’s Theorem. While calculating Rth, we cannot simply open circuit current sources and short circuit voltage sources because the voltage or current of the dependent sources depends on the independent sources.
While calculating Rth, we will short circuit the open terminals of the Thevenin circuit and calculate Isc (short circuit current). Then divide Vth by Isc to calculate Rth. 🔑 Rth = Vth / Isc
Example: Calculating Voltage V₀ using Thevenin’s Theorem with Dependent Source
First step: Removing RL RL is the 6kΩ resistor at which V₀ is to be calculated.
Second step: Calculating Vth Voltage across 4k resistor: V₄ₖ = (4k/6k) x 12 = 8 volts
Voltage across 2k resistor: V₂ₖ = (2k/6k) x 12 VA = V₂ₖ = 4 volts
Vth = 8 – 4VA = 8 – 4(4) = 8 – 16 🔑 Vth = -8 volts
Third step: Calculating Rth Replace the open circuit with a short circuit to find Isc.
VA = 2kI₁
Applying KVL to loop 1: For the other loop: -12 + 2kI₁ + (I₁ – Isc)4k = 0 -12 + 2kI₁ + 4kI₁ – 4kIsc = 0 6kI₁ – 4kIsc = 12 ————— (1)
For the supermesh containing the dependent source: (Isc – I₁)4k + 4VA = 0 4kIsc – 4kI₁ + 4(2kI₁) = 0 4kIsc – 4kI₁ + 8kI₁ = 0 4kIsc + 4kI₁ = 0 I₁ = -Isc
Putting in equation (1): 6k(-Isc) – 4kIsc = 12 -6kIsc – 4kIsc = 12 -10kIsc = 12 Isc = -6/5 mA
🔑 Rth = Vth/Isc = -8 / (-6/5 m) = 6.67kΩ
Fourth step: Calculating unknown quantity V₀ = (6k / (6k + 6.67k)) x 8 = (6k / 12.67k) x 8 📐 V₀ = 3.78 volts
⭐ Key Takeaways
Thevenin’s Theorem simplifies any linear circuit to a single voltage source (Vth) in series with a single resistor (Rth). For circuits with only independent sources, Rth is found by shorting voltage sources and opening current sources, then calculating the equivalent resistance. For circuits with dependent sources, Rth must be found using the short-circuit current method: Rth = Vth / Isc. Maximum power is transferred to the load when RL equals Rth, and the maximum power is calculated using Pmax = Vth² / (4Rth). The four-step procedure—removing RL, finding Vth, finding Rth, and reconnecting RL—is universally applicable.
🧠 Quick Revision Questions
- What is the value of Vth in Example 1, and explain the sign?
- How is Rth calculated differently for circuits with dependent sources compared to independent sources?
- What condition must be satisfied for maximum power transfer, and what is the formula for maximum power?
- In the dependent source example, why was the open circuit replaced with a short circuit, and what value of Isc was found?
- Using the results of Example 3, what would the load voltage be if a 4kΩ resistor were used instead of the 2kΩ load?
📘 Lecture 27 — Thevenin's Theorem and Dependent sources with examples - Norton's Theorem with examples
📖 Overview: This lecture demonstrates the application of Thevenin's theorem to circuits containing dependent sources, followed by an introduction and application of Norton's theorem. Mastering these theorems is essential for simplifying complex circuits into equivalent voltage or current sources with a single resistance, making analysis of load currents and voltages straightforward.
🗂️ Topics Covered
The lecture begins with two detailed examples of applying Thevenin's theorem, one with a dependent source requiring calculation of short-circuit current for Thevenin resistance. It then introduces Norton's theorem as a dual approach, explaining the four-step process and illustrating it with two examples involving both independent and dependent sources, culminating in load voltage calculations.
📝 Lecture Summary
Thevenin's Theorem with Dependent Sources
Thevenin's theorem states that any linear circuit can be replaced by an equivalent voltage source (Vth) in series with an equivalent resistance (Rth). When a circuit contains a dependent source (also called a controlled source), the Thevenin resistance cannot be found by simply deactivating independent sources and combining resistances. Instead, Rth is calculated by finding the open-circuit voltage (Vth) and dividing it by the short-circuit current (Isc) flowing from the open terminals when they are shorted: Rth = Vth / Isc.
🔑 Definition — Thevenin's Theorem: A linear two-terminal circuit can be replaced by an equivalent circuit consisting of a voltage source Vth in series with a resistor Rth, where Vth is the open-circuit voltage at the terminals and Rth is the resistance seen from the terminals with all independent sources deactivated (dependent sources remain).
📐 Formula: Rth = Vth / Isc → The Thevenin resistance is the ratio of the open-circuit voltage to the short-circuit current measured at the same terminals.
💡 Why this matters: This method is required when dependent sources are present because they cannot be simply turned off; the circuit must remain active to define the relationship between the controlling and controlled variables.
Example 1: Calculate current Io using Thevenin's theorem.
- Circuit: A 12V source, resistors: 8kΩ, 4kΩ, 12kΩ, 4kΩ, and a dependent voltage source (2Vx). Load resistor RL = 2kΩ across which Io flows.
- Step 1: Remove RL (the 2kΩ resistor) to find Vth.
- Step 2: Calculate Vth (open-circuit voltage).
- Voltage at node A: VA = (4kΩ × 12V) / (4kΩ + 8kΩ) = 48/12 = 4V.
- Voltage at node B: Vx = VA = 4V. VB = (4kΩ × 2Vx) / (12kΩ + 4kΩ) = (4kΩ × 8V) / 16kΩ = 2V.
- Vth = VAB = VA - VB = 4V - 2V = 2V.
- Step 3: Calculate Rth by finding Isc.
- Short the open terminals (A and B) and find the short-circuit current Isc.
- Apply KCL at node 1 (V1, where Vx = V1): (V1 - 12)/8k + V1/4k + V1/4k + (V1 - 2V1)/12k = 0.
- Solving: 3V1 - 36 + 6V1 + 6V1 + 2V1 - 4V1 = 0 → 13V1 = 36 → V1 = 36/13 V.
- Calculate branch currents: I1 = (12 - V1)/8k = (12 - 36/13)/8k = 120/13k = 15/13 mA ≈ 1.15mA.
- I2 = V1/4k = (36/13)/4k = 9/13 mA ≈ 0.692mA.
- I4 = V1/4k = 9/13 mA = 0.692mA.
- I5 = (V1 - 2V1)/12k = (-V1)/12k = (-36/13)/12k = -3/13 mA ≈ -0.23mA.
- Isc = I3 = I5 + I4 = -0.23mA + 0.692mA = 0.462mA ≈ 0.46mA.
- Rth = Vth / Isc = 2V / 0.46mA = 4.33kΩ.
- Step 4: Re-insert RL in series with Rth and Vth.
- Io = Vth / (Rth + RL) = 2V / (4.33kΩ + 2kΩ) = 2V / 6.33kΩ = 0.315mA.
Example 2: Calculate voltage Vo using Thevenin's theorem.
- Circuit: A 12V source, resistors: 2kΩ (2 of them), 1kΩ, and a dependent current source (2Vx). Load resistor RL = 2kΩ across which Vo appears.
- Step 1: Remove RL (the 2kΩ) to find Vth.
- Step 2: Calculate Vth (open-circuit voltage).
- At node 1, define Vx = V1 + 12.
- KCL at node 1: V1/2k + 2Vx/1k + Vx/2k = 0.
- Substitute Vx: V1 + 4(V1+12) + (V1+12) = 0 → V1 + 4V1 + 48 + V1 + 12 = 0 → 6V1 = -60 → V1 = -10V.
- Then Vx = V1 + 12 = -10 + 12 = 2V = Vth.
- Step 3: Calculate Rth by finding Isc.
- Short the output terminals. Now Vx = 0? No, Vx is defined relative to the dependent source. When shorted, the node voltages change. The circuit is re-analyzed.
- With the short, apply KCL at the node above the dependent source (V1). Vx = V1 + 12.
- KCL: V1/2k + 2Vx/1k + Vx/2k + Vx/2k = 0. (Note: an extra Vx/2k term appears due to the short circuit path.)
- Substitute Vx: (Vx - 12) + 4Vx + Vx + Vx = 0 → Vx - 12 + 6Vx = 0 → 7Vx = 12 → Vx = 12/7 V.
- Isc flows through the 2kΩ resistor to the short. Isc = Vx / 2k = (12/7) / 2k = 6/7 mA ≈ 0.857mA.
- Rth = Vth / Isc = 2V / (6/7 mA) = 2 × 7/6 kΩ = 7/3 kΩ = 2.33kΩ.
- Step 4: Re-insert RL in series with Rth and Vth.
- Vo = Vth × RL / (Rth + RL) = 2V × 2kΩ / (2.33kΩ + 2kΩ) = 4 / 4.33 = 0.92V.
Norton's Theorem
Norton's theorem is the dual of Thevenin's theorem. It states that any linear circuit can be replaced by an equivalent current source (In) in parallel with an equivalent resistance (Rn). The four steps are similar: (1) Remove the load to calculate the Norton current or resistance, (2) Find In by short-circuiting the open terminals and calculating the short-circuit current, (3) Find Rn (which equals Rth) by deactivating all independent sources and calculating the equivalent resistance, (4) Re-insert the load in parallel with Rn and In.
🔑 Definition — Norton's Theorem: A linear two-terminal circuit can be replaced by an equivalent circuit consisting of a current source In in parallel with a resistor Rn, where In is the short-circuit current at the terminals and Rn is the input resistance at the terminals with all independent sources deactivated.
📐 Formula: Rn = Vth / In → The Norton resistance equals the Thevenin resistance; the Norton current equals the short-circuit current.
Example 3: Calculate voltage Vo using Norton's theorem (independent sources).
- Circuit: A 12V source, 6V source, resistors (6kΩ, 3kΩ, 2kΩ, 1kΩ), and a 1mA current source. Load resistor RL = 4kΩ across which Vo appears.
- Step 1: Short RL (the 4kΩ) to find In.
- Step 2: Calculate In (short-circuit current).
- Define loop currents I1 (left loop) and I2 (right loop, through the short).
- KVL Loop 1: 6k(I1) + 3k(I1 - I2) - 12 - 6 = 0 → 9k I1 - 3k I2 = 18 → 9I1 - 3I2 = 18.
- KVL Loop 2: 2k(I2) + 1 + 3k(I2 - I1) = 0 → 5k I2 - 3k I1 = -12 → 5I2 - 3I1 = -12.
- Solve: Multiply eq2 by 3: 15I2 - 9I1 = -36. Add to eq1: (9I1 - 3I2) + (15I2 - 9I1) = 18 - 36 → 12I2 = -18 → I2 = -1.5mA.
- In = I2 = -1.5mA.
- Step 3: Calculate Rn.
- Deactivate voltage sources (short 12V and 6V) and current source (open 1mA).
- From the open terminals looking in: 6kΩ || 3kΩ = 2kΩ. This is in series with 2kΩ = 4kΩ.
- Rn = 4kΩ.
- Step 4: Re-insert RL in parallel with Rn and In (current source direction gives negative current).
- Current through RL (using current division): IL = In × Rn / (Rn + RL) = (-1.5mA) × 4kΩ / (4kΩ + 4kΩ) = -6 / 8 = -0.75mA.
- Vo = IL × RL = -0.75mA × 4kΩ = -3V.
Example 4: Calculate voltage Vo using Norton's theorem (dependent source).
- Circuit: A 2V source, 4mA current source, resistors: 4kΩ, 3kΩ, 6kΩ, 2kΩ, 8kΩ. Load resistor RL = 4kΩ across which Vo appears.
- Step 1: Short RL (the 4kΩ at the output) to find In.
- Step 2: Calculate In (short-circuit current).
- Define nodes: Node 1 (at the junction of 4k, 3k, 6k, and 4mA source), Node 2 (at the junction of 2k and 8k).
- KCL at Node 1 (V1): V1/4k + (V1 - 2)/3k + V1/6k + 4m = 0.
- Multiply by 12k: 3V1 + 4(V1-2) + 2V1 + 48 = 0 → 3V1 + 4V1 - 8 + 2V1 + 48 = 0 → 9V1 + 40 = 0 → V1 = -40/9 V ≈ -4.44V.
- KCL at Node 2 (V2): V2/2k + V2/8k - 4m = 0.
- Multiply by 8k: 4V2 + V2 - 32 = 0 → 5V2 = 32 → V2 = 32/5 = 6.4V.
- Short-circuit current Isc flows from V2 through 8k to V1? No, the short connects the right terminal to ground. Isc has two paths: I1 (from V2 through 8k to ground) and I2 (from V1 through 4k to ground).
- I1 = V2 / 8k = 6.4V / 8k = 0.8mA.
- I2 = V1 / 4k = -4.44V / 4k = -1.11mA (negative means current flows into the short from the right side).
- In = Isc = I1 + I2 = 0.8mA + (-1.11mA) = -0.31mA.
- Step 3: Calculate Rn.
- Deactivate all independent sources (short 2V, open 4mA).
- Simplify: 3kΩ || 6kΩ = 2kΩ. This is in series with 4kΩ = 6kΩ.
- Also: 8kΩ in series with 2kΩ = 10kΩ.
- Finally: 6kΩ || 10kΩ = (6 × 10) / 16 = 60/16 = 3.75kΩ = Rn.
- Step 4: Re-insert RL in parallel with Rn and In.
- Current through RL (current division): IL = In × Rn / (Rn + RL) = 0.31mA × 3.75kΩ / (3.75kΩ + 4kΩ) = 1.1625 / 7.75 = 0.15mA. (Note: the text shows 0.14mA, likely due to rounding).
- Vo = IL × RL = 0.15mA × 4kΩ = 0.6V. (The text calculates Vo = 0.56V).
⭐ Key Takeaways
The critical concept is that Thevenin and Norton theorems provide two equivalent ways to simplify a complex linear circuit: a voltage source in series with a resistance, or a current source in parallel with a resistance. For circuits with dependent sources, you cannot simply deactivate all sources to find the equivalent resistance; you must find both the open-circuit voltage (Vth) and the short-circuit current (Isc), then compute Rth = Vth / Isc. Norton's theorem is the dual, where the Norton current (In) equals the short-circuit current, and the Norton resistance (Rn) equals the Thevenin resistance. The four-step process is the same for both theorems, but the final equivalent circuit is different: series for Thevenin and parallel for Norton. Finally, the choice between using Thevenin or Norton is often a matter of convenience, depending on which calculation (open-circuit voltage or short-circuit current) is easier to perform.
🧠 Quick Revision Questions
- What is the difference between finding the Thevenin resistance for a circuit with only independent sources versus one that includes dependent sources?
- Explain why the Thevenin resistance can be found by Rth = Vth / Isc when dependent sources are present.
- In Norton's theorem, how is the Norton current (In) calculated, and how does it relate to Thevenin's theorem?
- For the circuit in Example 1, what is the value of the short-circuit current (Isc) and the resulting Thevenin resistance?
- In Example 4 (Norton's with dependent source), describe the steps to find the Norton resistance and the final load voltage.
📘 Lecture 28 — Norton's Theorem with examples - Linearity Principle
📖 Overview: This lecture continues the study of Norton's Theorem through multiple worked examples, demonstrating how to find Norton equivalent circuits for various network configurations. It also introduces the Linearity Principle as an alternative analysis technique that allows circuit solving by assuming an unknown value and scaling based on the actual source value.
🗂️ Topics Covered
The lecture covers multiple examples applying Norton's Theorem to find equivalent circuits and calculate currents/voltages in resistive networks. It demonstrates the step-by-step Norton procedure including finding Norton current (I_N) by short-circuiting the load, calculating Norton resistance (R_N) by deactivating independent sources, and re-inserting the load. The lecture also introduces the Linearity Principle, showing how to work backwards from an assumed output to find the actual circuit values through proportional scaling.
📝 Lecture Summary
Norton's Theorem: First Example
The simplest example demonstrates finding the Norton equivalent circuit. First, remove the load resistor R_L and replace the open circuit with a short circuit. By Ohm's Law, the Norton current I_N = 12V/0Ω → ∞A. Then insert resistance R=0Ω parallel to the current source to obtain the Norton equivalent circuit.
🔑 Definition — Norton Current (I_N): The current that flows through a short circuit placed across the terminals of the load. 🔑 Definition — Norton Resistance (R_N): The equivalent resistance seen from the load terminals when all independent sources are deactivated (voltage sources shorted, current sources opened).
Norton's Theorem: Second Example (with Dependent Source)
To calculate Norton's current through a circuit containing a dependent source, inject a 1A current source into the port. Define V_x across the 200Ω resistor.
For node 1: V_1/100 + (V_1 - V_x)/50 = 1, giving 3V_1 - 2V_x = 100 ...equation (A)
For node 2: -0.1V_1 = V_x/200 + (V_x - V_1)/50, giving -20V_1 = V_x + 4V_x - 4V_1, which simplifies to -16V_1 = 5V_x, or 5V_x + 16V_1 = 0 ...equation (B)
Solving simultaneously: 10V_x + 32V_1 = 0 and -10V_x + 15V_1 = 500, giving 47V_1 = 500, V_1 = 10.64V.
Therefore R_th = R_N = V_1/1A = 10.64Ω. Since no independent source exists in the circuit, I_N = 0A.
💡 Why this matters: When dependent sources are present but no independent sources, the Norton current is zero and only the Norton resistance matters for the equivalent circuit.
Norton's Theorem: Third Example (Using Superposition)
Calculate voltage V_o using Norton's theorem (no loop or node methods allowed, use superposition).
Step 1: Replace R_L (6kΩ) with a short circuit to find I_N.
Step 2: Calculate I_N using superposition.
- Only current source acting: Due to short circuit, all current flows through the short circuit, so I_N1 = 2mA ...(A)
- Only voltage source acting: 4kΩ is parallel with 2kΩ, in series with 2kΩ. Total resistance R = (4k||2k) + 2k = 8/6k + 2k = 3.33kΩ. I_N2 = 6V/3.33kΩ = 1.80mA ...(B)
Total I_N = I_N1 + I_N2 = 2mA + 1.80mA = 3.80mA
Step 3: Calculate R_N by shorting voltage sources and opening current sources. 4k||2k + 2k = 1.33kΩ + 2kΩ = 3.33kΩ = R_N.
Step 4: Re-insert load R_L in parallel with R_N and I_N current source. Using current divider rule: I_0 = (3.80mA)(3.33kΩ) × 1/(9.33kΩ) = 1.356mA.
By Ohm's Law: V_0 = 6kΩ × 1.35mA = 8.143 volts.
📐 Formula: Current Divider Rule: I_x = I_total × (R_parallel)/(R_parallel + R_branch)
Norton's Theorem: Fourth Example
Calculate current I_o using Norton's theorem with R_L = 6kΩ.
Step 1: Replace R_L with short circuit to find I_N.
Step 2: Calculate I_N using mesh analysis.
- Loop 2: I_2 = 2mA
- Loop 1: 4k(I_1-I_N) + 2k(I_1-I_2) - 6 = 0, giving 6kI_1 - 4kI_N = 10 ...(eq1)
- Loop 3: 4k(I_N-I_2) + 4k(I_N-I_1) = 0, giving -4kI_1 + 8kI_N = 8 ...(eq2)
Solving eq1 and eq2: 12kI_1 - 8kI_N = 20 and -12kI_1 + 24kI_N = 24, giving 16kI_N = 44, I_N = 2.75mA.
Step 3: Calculate R_N by shorting voltage sources and opening current sources. R_N = (2k||4k) + 4k = ((2k×4k)/(2k+4k)) + 4k = 1.33kΩ + 4kΩ = 5.33kΩ.
Step 4: Re-insert load. I_o = (2.75mA)(5.33kΩ) × 1/(6kΩ+5.33kΩ) = 1.29mA.
Linearity Principle
In this technique, assume the unknown quantity and analyze the circuit in reverse manner until reaching the source. Compare the calculated source value with the actual source value to find the exact unknown quantity by proportional scaling.
🔑 Definition — Linearity Principle: A method where an unknown circuit variable is assumed (typically 1V or 1A), the circuit is analyzed backwards to find what source value would produce that assumption, then the result is scaled proportionally to match the actual source value.
Linearity Principle Example
Calculate V_o by linearity principle. Assume V_o = 1V.
V_2 = 1V, so I_2 = 1V/2kΩ = 0.5mA V_4k = (0.5mA)(4kΩ) = 2V V_1 = V_4k + V_2 = 2V + 1V = 3V I_1 = 3V/3kΩ = 1mA I_s = I_2 + I_1 = 0.5mA + 1mA = 1.5mA V_2k = I_s(2kΩ) = (1.5mA)(2kΩ) = 3V V_s = V_2k + V_1 = 3V + 3V = 6V
When V_o is 1V, source voltage is 6V. Original source voltage is 12V, so output voltage scales proportionally: V_o = (12V/6V) × 1V = 2 Volts.
📐 Formula: Linear Scaling: Actual output = (Actual source value / Calculated source value) × Assumed output 📌 Example: (12V/6V) × 1V = 2V
⭐ Key Takeaways
The Norton equivalent circuit consists of a current source I_N in parallel with a resistance R_N, which can be found by short-circuiting the load terminals to measure I_N and deactivating all independent sources to calculate R_N. For circuits with dependent sources but no independent sources, I_N is zero but R_N can still be found using a test source (1A). When multiple independent sources are present, superposition can be used to find I_N by considering each source individually. The Linearity Principle provides an efficient alternative to nodal or mesh analysis by assuming a convenient value for the unknown, working backwards to find the required source value, then scaling proportionally to match the actual source—this method works because circuits with only linear elements follow the principle of proportionality.
🧠 Quick Revision Questions
- What are the four steps to find the Norton equivalent circuit?
- In the linearity principle example, why was V_o found to be 2V when the original source was 12V and the assumed V_o of 1V required a 6V source?
- When a circuit contains a dependent source but no independent sources, what is the value of I_N and how do you find R_N?
- How was the current divider rule applied in the third Norton example to find I_o from I_N?
- In the fourth Norton example, why were two simultaneous equations needed to solve for I_N, and what method was used?
📘 Lecture 29 — Basic Semiconductor Concepts
📖 Overview: This lecture introduces fundamental semiconductor concepts, focusing on intrinsic silicon's structure and behavior. It explains energy bands, carrier transport mechanisms (drift and diffusion), and the characteristics of doped semiconductors and p-n junctions under different bias conditions. These concepts form the foundation for understanding electronic devices like diodes and transistors.
🗂️ Topics Covered
The lecture covers intrinsic silicon crystal structure and covalent bonding, thermal ionization and recombination, energy band theory including conduction band, valence band, and band gap energy. It then explains drift and diffusion processes, doped semiconductors (n-type and p-type), and the behavior of p-n junctions under no bias, reverse bias, and forward bias conditions, including the formation of the depletion region.
📝 Lecture Summary
Intrinsic Silicon
A crystal of pure or intrinsic silicon has a regular lattice structure. The atoms are held at their fixed positions by bonds called Covalent bonds, formed by four valence electrons associated with each silicon atom.
At sufficiently low temperatures, these covalent bonds are intact and very few free electrons are available to conduct electric current.
Thermal ionization results in free electrons and holes in equal numbers and hence equal concentrations. These free electrons and holes move randomly through the silicon crystal structure, and in this process some electrons may fill some of the holes. This process is called RECOMBINATION.
Recombination results in disappearance of free electrons and holes. The recombination rate is proportional to the number of free electrons and holes, which in turn is determined by ionization rate.
Conduction Band
In semiconductors and insulators, there is a band gap above the valence band, called a conduction band. In a semiconductor, the range of electron energy, higher than that of the valence band, is sufficient to make the electrons free to move from atom to atom under the influence of an applied electric field and thus constitute an electric current.
Valence Band
At 0°K, the outermost electrons of an atom of a semiconductor material (such as silicon and germanium) are present in valence orbits. Associated with these orbits is a band of energies that is termed as valence band of energy.
Band Gap
The difference of energy between valence band and conduction band is called band gap energy.
Drift
The process whereby charged particles move under the influence of an electric field.
When there are few electrons present in the nearby valence band and we apply an electric field to such a material, these electrons may drift due to the applied field. This results in observable activity in the electrical property of the material, and some flow of current is observed. Such materials are called conductors.
When all energy levels are fully filled with electrons and we apply an electric field, these electrons have no space to drift. Such materials act as insulators, which offer maximum resistance to the flow of electrons and have very low conductivity.
When almost all energy levels are full except two levels kept empty, and we apply an electric field, these electrons have some space to drift. We observe some flow of current through such materials, so these are called conductors. Conductors offer zero resistance to the flow of electrons and have maximum conductivity.
Band Gap Energy
It is the energy required to excite an electron from its valence band to a conduction band and is denoted as Eg.
Diffusion
The process of flow of particles from a region of high concentration to a region of low concentration.
Diffusion Current
The current that results from the diffusion of charged particles.
Drift Velocity
The average velocity of charged particles in the presence of an electric field.
Doped Semiconductors
Doped semiconductors are materials in which carriers of one kind (electrons or holes) predominate.
Doped silicon in which the majority of charge carriers are negatively charged electrons is called n type.
Silicon doped so that majority of charge carriers are positively charged holes is called p type.
Doping of silicon to turn it into p type or n type is achieved by a small number of impurity atoms.
For instance, introducing impurity atoms of a pentavalent element such as phosphorus results in n type silicon.
No Bias — The Diffusion Current ID
Because the concentration of holes is high in the p region and low in the n region, holes diffuse across the junction from the p region to the n region.
Similarly, electrons diffuse across the junction from n side to p side.
These two current components add together to form the diffusion current ID, whose direction is from p side to n side.
The Depletion Region
The electrons that diffuse across the region quickly recombine with some of the majority holes present in the p region and thus disappear from the scene.
This results also in disappearance of some majority holes, causing some of the bound negative charge to be uncovered (no longer neutralized by holes). Thus in the p material close to the junction, a region is depleted of free electrons.
This p region will contain uncovered bound negative charge.
From the above it follows that a carrier depletion region will exist on both sides of the junction, with the n side of this region positively charged and p side negatively charged. This carrier depletion region, or simply depletion region, is also called the SPACE CHARGE REGION.
The P-N Junction Under Reverse Bias Condition
The pn junction is excited by a constant current source I in the reverse direction. To avoid breakdown, I is kept smaller than IS.
The depletion layer widens and the barrier voltage increases by VR volts, which appears between the terminals as reverse voltage.
The current I will be carried by electrons flowing in the external circuit from the n material to p material (in direction opposite to that of I).
This will cause electrons to leave the n material and holes to leave p material. Thus reverse current I will result in an increase in the width of, and the charge stored in, the depletion layer, which will increase the voltage across the depletion region.
The P-N Junction Under Forward Bias Condition
The pn junction is excited by a constant current source supplying a current I in the forward direction. The depletion layer narrows and barrier voltage decreases by V volts, which appears as an external voltage in the forward direction.
This current causes majority carriers to be supplied to both sides of the junction by the external circuit — holes to the p material and electrons to the n material.
These majority carriers will neutralize some of the uncovered charges, causing less charge to be stored in the depletion region. Thus the depletion layer narrows and the depletion barrier voltage reduces.
This reduction in voltage causes more electrons to move from n side to p side and more holes to move from p side to n side, so that diffusion currents increase until equilibrium is achieved.
💡 Why this matters: Understanding p-n junction behavior under different bias conditions is essential for analyzing diodes, rectifiers, and all semiconductor devices in electronic circuits.
⭐ Key Takeaways
Intrinsic silicon has covalent bonds that hold atoms together, and at low temperatures few free electrons exist. Thermal ionization creates equal numbers of electrons and holes, and recombination annihilates them. Energy bands include the valence band, conduction band, and band gap — the energy difference between them. Drift is carrier movement due to an electric field, while diffusion is carrier movement due to concentration gradients. Doped semiconductors can be n-type (excess electrons) or p-type (excess holes). The p-n junction under no bias has a diffusion current and forms a depletion region with positive n-side and negative p-side charges. Under reverse bias, the depletion layer widens and barrier voltage increases; under forward bias, the depletion layer narrows and barrier voltage decreases.
🧠 Quick Revision Questions
- What are covalent bonds in intrinsic silicon, and how many valence electrons does each silicon atom contribute to them?
- What is recombination, and what determines its rate in intrinsic silicon?
- How does the depletion region width change under reverse bias versus forward bias conditions?
- What is the difference between drift current and diffusion current in semiconductors?
- What type of impurity element (pentavalent or trivalent) is added to create n-type silicon, and why?