π Lecture Summary
1. Rigid Body Definition
A rigid body is one where all parts of the body are fixed relative to each other (for example, a pencil). Fluids and gases are non-rigid.
2. Translational and Rotational Motion
The translational motion of the centre of mass of a rigid body is governed by:
- Net external force: $\frac{d\vec{P}}{dt} = \vec{F}$ where $\vec{F} = \sum \vec{F}_{ext}$
- Net external torque: $\frac{d\vec{L}}{dt} = \vec{\tau}$ where $\vec{\tau} = \sum \vec{\tau}_{ext}$
π Definition β Mechanical Equilibrium: A rigid body is in mechanical equilibrium if both the linear momentum $\vec{P}$ and angular momentum $\vec{L}$ have a constant value, i.e., $\frac{d\vec{P}}{dt} = 0$ and $\frac{d\vec{L}}{dt} = 0$. Static equilibrium refers to $\vec{P} = 0$ and $\vec{L} = 0$.
3. Example: Beam on Supports
Consider a beam resting on supports with force $F_1$ and $F_2$ pushing upward:
Step 1 β Force balance in vertical y-direction: $$\sum F_y = F_1 + F_2 - Mg - mg = 0$$
Step 2 β Torque balance: $$\sum \tau_y = (F_1)(0) + (F_2)(L) - (Mg)(L/4) - (mg)(L/2) = 0$$
From these two conditions: $$F_1 = \frac{3M + 2m}{4}g, \quad F_2 = \frac{M + 2m}{4}g$$
4. Choice of Origin and Torque
Torque depends on where you choose the origin of coordinates. For a body in equilibrium, the choice of origin does not matter.
Proof: Torque about point O: $\vec{\tau}_O = \vec{r}_1 \times \vec{F}_1 + \vec{r}_2 \times \vec{F}_2 + \cdots + \vec{r}_N \times \vec{F}_N$
Torque about point P (shifted by $\vec{r}_P$): $$\vec{\tau}_P = [\vec{r}_1 \times \vec{F}_1 + \vec{r}_2 \times \vec{F}_2 + \cdots + \vec{r}_N \times \vec{F}_N] - [\vec{r}_P \times (\vec{F}_1 + \vec{F}_2 + \cdots + \vec{F}_N)]$$ $$\vec{\tau}_P = \vec{\tau}O - [\vec{r}P \times (\sum F{ext})]$$ Since $\sum F{ext} = 0$ for a body in translational equilibrium, $\vec{\tau}_P = \vec{\tau}_O$.
π‘ Why this matters: This shows the torque about any point is the same for a body in equilibrium, making calculations more flexible.
5. Practical Balance Problem
Consider a balance in equilibrium with two known weights. To find mass $m$ in terms of $m_1$ and $m_2$:
Taking torques about the knife edge in two cases:
- $mgx = m_1 g (L - x)$
- $m_2 g x = mg (L - x)$
This gives: $\frac{m}{m_1} = \frac{m_2}{m}$ or $m = \sqrt{m_1 m_2}$
π Remarkably: We do not need the values of $x$ or $L$ to find $m$.
6. Centre of Gravity
The centre of gravity (CG) is the average location of the weight of an object. The net force on the whole body equals the sum of forces over all individual particles: $\vec{F} = \sum m_i \vec{g} = M\vec{g}$ where $M$ is the total mass.
If $\vec{g}$ has the same value at all points of the body, then:
- The weight is equal to $M\vec{g}$
- The centre of gravity coincides with the centre of mass
The net torque about the centre of mass due to gravity about the centre of mass of a body is zero.
7. Finding CG by Suspension
The CG of an irregular object can be found by suspending it on a pivot. The object will hang such that the CG is directly below the pivot point.
8. Non-Uniform Bar Problem
A non-uniform bar of weight $W$ is suspended at rest horizontally by two light cords. Find distance $x$ from left-hand end to centre of gravity.
Solution:
- Horizontal: $T_2 \sin\phi - T_1 \sin\theta = 0$
- Vertical: $T_2 \cos\phi + T_1 \cos\theta - W = 0 \Rightarrow T_2 = \frac{W}{\sin(\theta + \phi)}$
Taking torque about one end: $$-Wx + (T_2 \cos\phi)L = 0 \Rightarrow x = \frac{(T_2 \cos\phi)L}{W} = \frac{L \cos\phi}{\sin(\theta + \phi)}$$
9. Rod Leaning Without Slipping
Find the least angle $\theta$ at which the rod can lean to the horizontal without slipping.
Translational equilibrium:
- $R_1 = \mu_2 R_2$
- $R_2 + \mu_1 R_1 = W$
This gives: $R_2 = \frac{W}{(1 + \mu_1 \mu_2)}$
Rotational equilibrium about point A: $R_2 \times OB = W \times OD + \mu_2 R_2 \times OA$ $R_2 \times AB \cos\theta = W \times \frac{AB \cos\theta}{2} + \mu_2 R_2 \times AB \sin\theta$
This gives: $\cos\theta(R_2 - \frac{W}{2}) = \mu_2 R_2 \sin\theta \Rightarrow \tan\theta = \frac{1 - \mu_1 \mu_2}{2\mu_2}$
10. Types of Equilibrium
Stable equilibrium: Object returns to its original position if displaced slightly. Unstable equilibrium: Object moves farther away from its original position if displaced slightly. Neutral equilibrium: Object stays in its new position if displaced slightly.
β Key Takeaways
For equilibrium of rigid bodies, both the sum of all external forces and the sum of all external torques must equal zero. Torque calculations give the same result regardless of the chosen reference point when translational equilibrium holds. The centre of gravity coincides with the centre of mass when gravitational acceleration is uniform. Practical problems involving beams, balances, and leaning rods are solved by applying force and torque balance simultaneously. Understanding the three types of equilibrium (stable, unstable, neutral) is essential for predicting the behavior of objects when displaced.
π§ Quick Revision Questions
-
What are the two conditions for a rigid body to be in mechanical equilibrium?
-
In the beam-on-supports example, what are the expressions for $F_1$ and $F_2$ in terms of $M$, $m$, and $g$?
-
Why does the choice of origin not affect torque calculations for a body in equilibrium?
-
In the balance problem, what is the mass $m$ in terms of $m_1$ and $m_2$?
-
What is the difference between stable, unstable, and neutral equilibrium?
π Lecture 15 β OSCILLATIONS: I
π Overview: This lecture introduces the fundamental concepts of oscillatory motion, including period, frequency, and amplitude. It derives the equation of motion for a simple harmonic oscillator (SHO) using a mass-spring system, solves the differential equation, and explores energy conservation in oscillatory systems. Understanding oscillations is crucial because they appear throughout physicsβfrom pendulums to molecular vibrations and electromagnetic waves.
ποΈ Topics Covered
The lecture covers the definition and characteristics of oscillations (period, frequency, amplitude), restoring forces and Hooke's Law, deriving the simple harmonic oscillator equation from Newton's second law, differentiating trigonometric functions to solve the SHO equation, interpreting the solution in terms of amplitude and phase, calculating energy (kinetic and potential) in oscillatory motion, speed as a function of displacement, and the effective spring constant for springs in parallel and series.
π Lecture Summary
1. Basic Characteristics of Oscillations
An oscillation is any self-repeating motion. This motion is characterized by three key quantities: the period ( T ), which is the time for completing one full cycle; the frequency ( f = 1/T ), which is the number of cycles per second (also denoted by ( \nu )); and the amplitude ( A ), which is the maximum displacement from equilibrium (or the size of the oscillation).
2. Why Systems Oscillate
A system oscillates because a force is always directed towards a central equilibrium position. In other words, the restoring force always acts to return the object to its equilibrium position. So the object will oscillate around the equilibrium position. The restoring force depends on the displacement: ( F_{\text{restore}} = -k\Delta x ), where ( \Delta x ) is the distance away from the equilibrium point, the negative sign shows that the force acts towards the equilibrium point, and ( k ) is a constant that gives the strength of the restoring force.
π Definition β Restoring Force: A force that acts to return a system to its equilibrium position, proportional to displacement and opposite in direction.
3. The Simple Harmonic Oscillator (SHO) Equation
For a spring tied to a mass that can move freely over a frictionless surface: ( F(x) = -kx ) (where ( x ) is the extension). The energy stored in the spring is ( U(x) = \frac{1}{2}kx^2 ). Using Newton's second law: ( m\frac{d^2x}{dt^2} = -kx ), which rearranges to: [ \frac{d^2x}{dt^2} + \omega^2 x = 0 \quad \text{where} \quad \omega^2 \equiv \frac{k}{m} ] This is the equation of motion of a simple harmonic oscillator (SHO).
π Definition β Simple Harmonic Oscillator (SHO): A system where the restoring force is directly proportional to displacement and acts in the opposite direction, described by ( \frac{d^2x}{dt^2} + \omega^2 x = 0 ).
π‘ Why this matters: The SHO equation ( \frac{d^2x}{dt^2} + \omega^2 x = 0 ) appears throughout physics. Only the definition of ( \omega ) changes depending on the physical situation.
π Formula: ( \frac{d^2x}{dt^2} + \omega^2 x = 0 ) β The acceleration is proportional to negative displacement, producing oscillatory motion.
4. Differentiating Trigonometric Functions
To solve the SHO equation, we first learn to differentiate trigonometric functions. Starting with the derivative of ( \cos\omega t ): [ \frac{d}{dt}\cos\omega t = -\omega\sin\omega t ] (Using ( \sin\theta \approx \theta ) for small ( \theta )). And the derivative of ( \sin\omega t ): [ \frac{d}{dt}\sin\omega t = \omega\cos\omega t ] (Using ( \cos\theta \approx 1 ) for small ( \theta )).
π Formula: ( \frac{d}{dt}\cos\omega t = -\omega\sin\omega t ) β The derivative of cosine is negative sine times omega. π Formula: ( \frac{d}{dt}\sin\omega t = \omega\cos\omega t ) β The derivative of sine is cosine times omega.
5. Second Derivatives
Differentiating twice gives back the original function with a negative factor: [ \frac{d^2}{dt^2}(\sin\omega t) = \frac{d}{dt}(\omega\cos\omega t) = -\omega^2\sin\omega t ] [ \frac{d^2}{dt^2}(\cos\omega t) = \frac{d}{dt}(-\omega\sin\omega t) = -\omega^2\cos\omega t ] So twice differentiating either ( \sin\omega t ) or ( \cos\omega t ) gives the same function back!
π Formula: ( \frac{d^2}{dt^2}(\sin\omega t) = -\omega^2\sin\omega t ) and ( \frac{d^2}{dt^2}(\cos\omega t) = -\omega^2\cos\omega t ).
6. Solution of the SHO Equation
Any function of the form ( x(t) = a\cos\omega t + b\sin\omega t ) satisfies ( \frac{d^2x}{dt^2} = -\omega^2 x ).
Interpretation of ( \omega ), ( a ), and ( b ):
a) Significance of ( \omega ): If we replace ( t ) by ( t + \frac{2\pi}{\omega} ) in either ( \sin\omega t ) or ( \cos\omega t ), the function repeats itself. So ( \frac{2\pi}{\omega} ) is the period ( T ): [ T = \frac{2\pi}{\omega} = 2\pi\sqrt{\frac{m}{k}} ] The frequency ( \nu = 1/T = \frac{1}{2\pi}\sqrt{\frac{k}{m}} ), so ( \omega = 2\pi\nu = \sqrt{\frac{k}{m}} ). ( \omega ) is called the angular frequency.
π Definition β Angular Frequency (( \omega )): The rate of change of phase per unit time, measured in radians/second, related to frequency by ( \omega = 2\pi\nu ).
π Formula: ( T = 2\pi\sqrt{\frac{m}{k}} ) β Period depends on mass and spring constant but NOT on amplitude.
b) Meaning of ( a ) and ( b ): From ( x(t) = a\cos\omega t + b\sin\omega t ):
- At ( t=0 ): ( x(0) = a ) β so ( a ) is the initial position
- ( \frac{dx}{dt} = -\omega a\sin\omega t + \omega b\cos\omega t ), so at ( t=0 ): ( \frac{dx}{dt} = \omega b ) β so ( b ) is the initial velocity divided by ( \omega )
c) Amplitude form: The solution can also be written as: [ x(t) = x_m \cos(\omega t + \phi) ] where ( x_m ) is the amplitude (maximum displacement), and ( \phi ) is the phase constant. Since ( -x_m \leq x \leq +x_m ), ( x_m ) is called the amplitude of the motion. The frequency of simple harmonic motion is independent of the amplitude.
d) The quantity ( \theta = \omega t + \phi ) is called the phase of the motion. A different value of ( \phi ) just means the origin of time has been chosen differently.
π Definition β Amplitude (( x_m )): The maximum displacement from equilibrium in oscillatory motion. π Definition β Phase (( \omega t + \phi )): The argument of the sine or cosine function in oscillatory motion, determining the state of the oscillator at any time ( t ). π Definition β Phase Constant (( \phi )): The initial phase at ( t=0 ), determining the starting point in the oscillation cycle.
7. Energy of Simple Harmonic Motion
With ( \phi = 0 ) (so ( x = x_m \cos\omega t )):
Potential Energy: [ U = \frac{1}{2}kx^2 = \frac{1}{2}kx_m^2 \cos^2\omega t ]
Kinetic Energy: [ K = \frac{1}{2}mv^2 = \frac{1}{2}m\left(\frac{dx}{dt}\right)^2 = \frac{1}{2}m\omega^2 x_m^2 \sin^2\omega t = \frac{1}{2}kx_m^2 \sin^2\omega t ]
Total Energy (sum of potential + kinetic): [ E = K + U = \frac{1}{2}kx_m^2 (\cos^2\omega t + \sin^2\omega t) = \frac{1}{2}kx_m^2 ]
The total energy is independent of time and energy goes from kinetic to potential, back to kinetic, etc.
π Formula: ( E = \frac{1}{2}kx_m^2 = \frac{1}{2}m\omega^2 x_m^2 ) β Total energy is constant and proportional to the square of the amplitude.
π‘ Why this matters: Energy conservation in SHM means the oscillator continuously converts between kinetic and potential energy without loss.
8. Speed as a Function of Displacement
From energy conservation: velocity ( v = \frac{dx}{dt} = \pm\sqrt{\frac{k}{m}(x_m^2 - x^2)} )
- Speed is maximum at ( x = 0 ) (equilibrium position)
- Speed is zero at ( x = \pm x_m ) (extreme positions)
π Formula: ( v = \pm\sqrt{\frac{k}{m}(x_m^2 - x^2)} ) β Speed depends on position, being maximum at equilibrium and zero at maximum displacement.
9. Springs in Parallel and Series
Parallel combination: Makes it harder to stretch them. The effective spring constant is: [ k_{\text{eff}} = k_1 + k_2 ]
Series combination: Makes them easier to stretch. The effective spring constant is: [ k_{\text{eff}} = \left(\frac{1}{k_1} + \frac{1}{k_2}\right)^{-1} ]
So a mass will oscillate faster in the parallel case compared to the series case.
π Formula (Parallel): ( k_{\text{eff}} = k_1 + k_2 ) β Stiffer spring, higher frequency. π Formula (Series): ( k_{\text{eff}} = \left(\frac{1}{k_1} + \frac{1}{k_2}\right)^{-1} ) β Softer spring, lower frequency.
β Key Takeaways
The simple harmonic oscillator is the fundamental model for all periodic motion, characterized by a restoring force proportional to displacement (( F = -kx )). Its equation of motion is ( \frac{d^2x}{dt^2} + \omega^2 x = 0 ) with solution ( x(t) = x_m \cos(\omega t + \phi) ), where ( \omega = \sqrt{k/m} ). Critically, the period ( T = 2\pi\sqrt{m/k} ) depends only on mass and spring constant, not on amplitude. The total mechanical energy ( E = \frac{1}{2}kx_m^2 ) remains constant, oscillating between kinetic and potential forms. Finally, springs in parallel produce a stiffer system (higher ( k ), faster oscillation) while springs in series produce a softer system (lower ( k ), slower oscillation).
π§ Quick Revision Questions
- What are the three basic characteristics that describe any oscillation?
- Write down the differential equation for a simple harmonic oscillator and define the angular frequency ( \omega ).
- Show that ( x(t) = x_m \cos(\omega t + \phi) ) satisfies the SHO equation.
- Derive expressions for kinetic energy, potential energy, and total energy in SHM. Prove that total energy is constant.
- Two identical springs of spring constant ( k ) are connected (a) in parallel and (b) in series. Find the effective spring constant in each case and state which combination makes a mass oscillate faster.
π Lecture 16 β Oscillations: II
π Overview: This lecture extends the concept of simple harmonic motion (SHO) to physical pendulums, damped oscillations, and forced oscillations. It explores how real systems behave under damping and driving forces, culminating in the critical concept of resonance, which has profound applications across physics and engineering.
ποΈ Topics Covered
The lecture begins by revisiting the simple pendulum and showing it approximates an SHO for small angles. It then generalizes to a physical pendulum, introducing the moment of inertia and center of gyration. Next, it covers the superposition of two SHMs along the same line, leading to constructive and destructive interference. This is followed by the composition of perpendicular SHMs, yielding elliptical and Lissajous figures. Finally, it introduces damped harmonic motion and forced oscillations with resonance.
π Lecture Summary
1. The Simple Pendulum Revisited
For a mass suspended from a string, the restoring force is ( F = -mg\sin\theta ). For small (\theta), (\sin\theta \approx \theta), and using ( x = L\theta ) we get ( F = -\left(\frac{mg}{L}\right)x ). This is proportional to displacement, so it is an SHO with angular frequency ( \omega = \sqrt{g/L} ). Even without the small-angle approximation, the motion is periodic but mathematically complex.
π Definition β Simple Harmonic Oscillator (SHO): A system where the restoring force is directly proportional to displacement from equilibrium. π Formula: ( \omega = \sqrt{g/L} ) β The angular frequency of a simple pendulum depends only on length and gravity. π Example: For a pendulum of length ( L = 1.0\ \text{m} ) and ( g = 9.8\ \text{m/s}^2 ), ( \omega = \sqrt{9.8/1.0} = 3.13\ \text{rad/s} ).
2. The Physical Pendulum
For an extended object pivoted at a point, torque is ( \tau = -Mgd\sin\theta ). For small (\theta), (\tau = -Mgd\theta). Using ( \tau = I\alpha ) and ( \alpha = d^2\theta/dt^2 ), we get ( I\frac{d^2\theta}{dt^2} = -Mgd\theta ) or ( \frac{d^2\theta}{dt^2} = -\left(\frac{Mgd}{I}\right)\theta ). Hence the oscillation frequency is ( \omega = \sqrt{Mgd/I} ). If the pivot is at the center of mass, torque vanishes and the object does not oscillate.
π Definition β Physical Pendulum: Any rigid body pivoted so it can swing freely under gravity. π Formula: ( \omega = \sqrt{Mgd/I} ) β Frequency depends on mass, gravity, distance from pivot to cm, and moment of inertia. π Example: For a uniform rod of length ( L ) pivoted at one end, ( d = L/2 ) and ( I = \frac{1}{3}ML^2 ), so ( \omega = \sqrt{\frac{Mg(L/2)}{(1/3)ML^2}} = \sqrt{\frac{3g}{2L}} ).
3. Centre of Gyration
If a physical pendulum is pivoted at a point P at distance ( L ) from the cm, and we want it to behave like a simple pendulum, we set ( T = 2\pi\sqrt{L/g} = 2\pi\sqrt{I/(Mgd)} ). Solving gives ( L = I/(Md) ). This point P is called the centre of gyration; from this pivot, the mass appears concentrated at the cm.
π Definition β Centre of Gyration: The point on a physical pendulum from which, if suspended, it oscillates as if all mass were at the cm. π Formula: ( L = I/(Md) ) β Equivalent simple pendulum length. π Example: For the rod above, ( I = \frac{1}{3}ML^2 ), ( d = L/2 ), so ( L = \frac{(1/3)ML^2}{M(L/2)} = \frac{2}{3}L ).
4. Sum of Two SHMs Along the Same Line
Given ( x_1 = A_1\sin\omega t ) and ( x_2 = A_2\sin(\omega t + \phi) ), their sum is ( x = R\sin(\omega t + \theta) ) where ( R = \sqrt{A_1^2 + A_2^2 + 2A_1A_2\cos\phi} ) and ( \tan\theta = \frac{A_2\sin\phi}{A_1 + A_2\cos\phi} ). For ( \phi = 0 ), ( R = A_1 + A_2 ) (constructive interference). For ( \phi = \pi ), ( R = |A_1 - A_2| ) (destructive interference).
π Definition β Superposition: Adding two waves of same frequency yields a wave with amplitude dependent on phase difference. π Formula: ( R = \sqrt{A_1^2 + A_2^2 + 2A_1A_2\cos\phi} ) π Example: If ( A_1 = 3\ \text{cm} ), ( A_2 = 4\ \text{cm} ), ( \phi = 0 ), then ( R = 3+4 = 7\ \text{cm} ); if ( \phi = \pi ), ( R = |3-4| = 1\ \text{cm} ).
5. Composition of Two Perpendicular SHMs
For ( x = A\sin\omega t ) and ( y = B\sin(\omega t + \phi) ), eliminating ( t ) gives the ellipse equation: ( \frac{x^2}{A^2} + \frac{y^2}{B^2} - \frac{2xy}{AB}\cos\phi = \sin^2\phi ). This is generally an ellipse; for special (\phi), it becomes a line or circle.
π Definition β Lissajous Figures: Curves formed by combining perpendicular oscillations; periodic only if frequency ratio is rational. π Formula: ( \frac{x^2}{A^2} + \frac{y^2}{B^2} - \frac{2xy}{AB}\cos\phi = \sin^2\phi )
6. Damped Harmonic Motion
Damping force is ( -b(dx/dt) ). Newton's law gives ( m\frac{d^2x}{dt^2} + b\frac{dx}{dt} + kx = 0 ). For weak damping (( k/m \geq (b/(2m))^2 )), the solution is ( x = x_0 e^{-bt/(2m)} \cos(\omega't + \phi) ) where ( \omega' = \sqrt{k/m - (b/(2m))^2} ). Amplitude decays to ( 1/e ) of initial value when ( bt/(2m) = 1 ).
π Definition β Damped Harmonic Motion: Oscillation with amplitude decreasing over time due to a dissipative force. π Formula: ( \omega' = \sqrt{k/m - (b/(2m))^2} ) π Example: For a mass ( m = 0.2\ \text{kg} ), spring constant ( k = 5\ \text{N/m} ), damping constant ( b = 0.1\ \text{kg/s} ), undamped ( \omega_0 = \sqrt{5/0.2} = 5\ \text{rad/s} ), damped ( \omega' = \sqrt{25 - (0.1/(0.4))^2} = \sqrt{25 - 0.0625} \approx 4.99\ \text{rad/s} ).
π‘ Why this matters: Damping explains why real oscillations eventually stop, crucial for shock absorbers, musical instruments, and building stability.
7. Forced Oscillation and Resonance
For a driving force ( F_0\cos\omega t ), the equation is ( m\frac{d^2x}{dt^2} + kx = F_0\cos\omega t ). The solution is ( x = \frac{F_0}{m(\omega_0^2 - \omega^2)}\cos\omega t ), where ( \omega_0 = \sqrt{k/m} ) is the natural frequency. Amplitude "blows up" (goes to infinity) as ( \omega \to \omega_0 ) in the absence of damping. With damping, amplitude remains finite but is maximized when driving frequency equals natural frequencyβthis is resonance.
π Definition β Resonance: Condition where a driving frequency matches the natural frequency, maximizing oscillation amplitude. π Formula: Amplitude = ( \frac{F_0}{m(\omega_0^2 - \omega^2)} ) (undamped) π Example: A child's swing (( \omega_0 \approx 1\ \text{rad/s} )) pushed at the same frequency results in large amplitude swings.
π‘ Why this matters: Resonance can be destructive (e.g., Tacoma Narrows Bridge collapse) or useful (e.g., tuning a radio, MRI imaging).
β Key Takeaways
The simple pendulum approximates an SHO only for small angles, with frequency ( \sqrt{g/L} ). A physical pendulum's frequency ( \sqrt{Mgd/I} ) generalizes this, introducing the center of gyration. Superposition of two SHMs produces interferenceβconstructive when in phase, destructive when out of phase. Perpendicular SHMs combine into elliptical or Lissajous patterns. Damping reduces amplitude over time, described by an exponential decay factor ( e^{-bt/(2m)} ). Forced oscillations exhibit resonance, where amplitude peaks dramatically when the driving frequency matches the natural frequencyβa critical phenomenon with vast practical implications.
π§ Quick Revision Questions
- What is the angular frequency of a simple pendulum of length 0.5 m on Earth?
- For a physical pendulum, what happens to the oscillation if the pivot is at the center of mass?
- Two SHMs of amplitudes 2 cm and 5 cm, same frequency, have a phase difference of 60Β°. What is the resultant amplitude?
- In damped harmonic motion, what does the damping constant ( b ) represent physically?
- What condition must the driving frequency satisfy for resonance to occur in an undamped forced oscillator?
π Lecture 17 β PHYSICS OF MATERIALS
π Overview: This lecture introduces the fundamental concepts of elasticity and plasticity in materials, covering how materials deform under various types of forces. It explains the key parameters that describe material behavior, including stress, strain, and elastic moduli, and extends these principles to fluids, pressure, and Pascal's Principle, which are essential for understanding material science and fluid mechanics.
ποΈ Topics Covered
The lecture covers elasticity and plasticity, definitions of stress (longitudinal, volume, and shearing) and strain (longitudinal, volume, and shearing), Hooke's Law and the three moduli of elasticity (Young's, Bulk, and Shear), Poisson's ratio, the work done in stretching a wire, the fundamental properties of fluids, the concept of pressure and density, the variation of pressure with depth in a fluid, and Pascal's Principle.
π Lecture Summary
1. Elasticity
If a body completely recovers its original shape and size when external forces are removed, it is called perfectly elastic. Quartz, steel and glass are very nearly elastic.
π Definition β Elasticity: the property by virtue of which a body tends to regain its original shape and size when deforming forces are removed.
2. Plasticity
If a body has no tendency to regain its original shape and size, it is called perfectly plastic. Common plastics, kneaded dough, solid honey, etc are plastics.
3. Stress
Stress characterizes the strength of the forces causing the stretch, squeeze, or twist. It is defined usually as force/unit area but may have different definitions to suit different situations. We distinguish between three types of stresses: a) If the deforming force is applied along some linear dimension of a body, the stress is called longitudinal stress or tensile stress or compressive stress. b) If the force acts normally and uniformly from all sides of a body, the stress is called volume stress. c) If the force is applied tangentially to one face of a rectangular body, keeping the other face fixed, the stress is called tangential or shearing stress.
4. Strain
Strain: When deforming forces are applied on a body, it undergoes a change in shape or size. The fractional (or relative) change in shape or size is called the strain. Strain = change / original dimension. Strain is a ratio of similar quantities so it has no units. There are 3 different kinds of strain: a) Longitudinal (linear) strain is the ratio of the change in length (ΞL) to original length (l), i.e., the linear strain = Ξl / l. b) Volume strain is the ratio of the change in volume (ΞV) to original volume (V). Volume strain = ΞV / V. c) Shearing strain: For small ΞΈ, the angular deformation (ΞΈ) in radians is called shearing strain. As shown in the diagram, ΞΈ β tan ΞΈ = Ξx / l, so shearing strain = ΞΈ = Ξx / l.
5. Hooke's Law
Hooke's Law: for small deformations, stress is proportional to strain. Stress = E Γ Strain. The constant E is called the modulus of elasticity. E has the same units as stress because strain is dimensionless. There are three moduli of elasticity. (a) Young's modulus (Y) for linear strain: Y = longitudinal stress / longitudinal strain = (F/A) / (Ξl/l). (b) Bulk Modulus (B) for volume strain: Let a body of volume V be subjected to a uniform pressure ΞP on its entire surface and let ΞV be the corresponding decrease in its volume. Then, B = Volume Stress / Volume Strain = - ΞP / (ΞV/V). 1/B is called the compressibility. A material having a small value of B can be compressed easily. Its value lies between 0 and 0.5. (c) Shear Modulus (Ξ·) for shearing strain: Let a force F produce a strain ΞΈ. Then, Ξ· = shearing stress / shearing strain = (F/A) / ΞΈ = F / (A * tan ΞΈ) = F / (A * Ξx/l).
6. Poisson's Ratio
When a wire is stretched, its length increases and radius decreases. The ratio of the lateral strain to the longitudinal strain is called Poisson's ratio, Ο = (Ξr / r) / (Ξl / l).
7. Work Done in Stretching a Wire
We can calculate the work done in stretching a wire. Obviously, we must do work against a force. If x is the extension produced by the force F in a wire of length l, then F = (YA/l) x. The work done in extending the wire through Ξl is given by, W = β«β^(Ξl) F dx = β«β^(Ξl) (YA/l) x dx = (YA/l) (ΞlΒ²/2) = (1/2) * Volume * Stress * Strain. We can also write this as, W = 1/2 * Load * Extension.
π Example: The work done in stretching a wire is calculated by integrating the force from 0 to the final extension Ξl. Since force F = (YA/l)x, the integral yields W = (YA/l)(ΞlΒ²/2).
8. Fluids
A fluid is a substance that can flow and does not have a shape of its own. Thus all liquids and gases are fluids. Solids possess all the three moduli of elasticity whereas a fluid possess only the bulk modulus (B). A fluid at rest cannot sustain a tangential force. If such force is applied to a fluid, the different layers simply slide over one another. Therefore the forces acting on a fluid at rest have to be normal to the surface. This implies that the free surface of a liquid at rest, under gravity, in a container, is horizontal.
9. Pressure and Density
The normal force per unit area is called pressure, P = ΞF / ΞA. Its unit is Newtons/metreΒ², or Pascal (Pa). Another scalar is density, Ο = Ξm / ΞV, where Ξm is the mass of a small piece of the material and ΞV is the volume it occupies. Pressure is a scalar quantity.
10. Variation of Pressure with Depth
Let us calculate how the pressure in a fluid changes with depth. Take a small element of fluid volume submerged within the body of the fluid: dm = Ο dV = Ο A dy, so (dm)g = ΟgA dy. Now let us require that the sum of the forces on the fluid element is zero: pA - (p+dp)A - ΟgAdy = 0 β dp/dy = -Οg. Note that we are taking the origin (y=0) at the bottom of the liquid. Therefore as the elevation increases (dy positive), the pressure decreases (dp negative). The quantity Οg is the weight per unit volume of the fluid. For liquids, which are nearly incompressible, Ο is practically constant. β dp/dy = Ξp/Ξy = (pβ - pβ) / (yβ - yβ) = -Οg β pβ - pβ = -Οg(yβ - yβ).
π Formula: dp/dy = -Οg β The rate of change of pressure with height is equal to the negative of the fluid's weight per unit volume.
11. Pascal's Principle
Pascal's Principle: Pressure applied to an enclosed fluid is transmitted to every portion of the fluid and to the walls of the containing vessel. This follows from the above: if h is the height below the liquid's surface, then p = p_ext + Οgh. Here p_ext is the pressure at the surface of the liquid, and so the difference in pressure is Ξp = Ξp_ext + Ξ(Οgh). Therefore, Ξ(Οgh) = 0 β Ξp = Ξp_ext (because liquids are incompressible). So the pressure is everywhere the same. The pressure in liquids is everywhere the same.
π‘ Why this matters: Pascal's Principle is fundamental to the operation of hydraulic systems, such as car brakes and lifts, where a small force applied at one point creates a large force at another.
β Key Takeaways
You must understand the distinction between elasticity and plasticity and memorize the three types of stress and strain. Hooke's Law with its three moduli (Young's, Bulk, and Shear) is critical, including their formulas and physical meanings, and you should know that Poisson's ratio relates lateral and longitudinal strain. The work done in stretching a wire can be expressed as half the product of load and extension, or half the product of volume, stress, and strain. Finally, for fluids, pressure increases linearly with depth (dp/dy = -Οg), and Pascal's Principle states that pressure is transmitted undiminished throughout an enclosed fluid.
π§ Quick Revision Questions
- What is the definition of stress, and what are the three types of stress described in the lecture?
- State Hooke's Law and write the formula for Young's modulus, Bulk modulus, and Shear modulus.
- A fluid at rest cannot sustain which type of force, and what is the consequence of this for its free surface?
- Derive the equation dp/dy = -Οg and explain what happens to pressure as you increase in elevation within a fluid.
- State Pascal's Principle and explain why the pressure is the same everywhere in an enclosed liquid.
π Lecture 18 β Physics of Fluids
π Overview: This lecture introduces the physics of fluids, covering surface tension, pressure differences in bubbles and drops, and the principles of fluid flow including the continuity equation and Bernoulli's equation. It explains fundamental concepts that are essential for understanding everyday phenomena like liquid surfaces, soap bubbles, and aircraft lift.
ποΈ Topics Covered
The lecture begins with the definition of fluids and molecular interactions, then explores surface tension as a property of liquids, its measurement using a sliding wire apparatus, and its representation as potential energy per unit area. It then examines pressure differences in soap bubbles and liquid drops due to surface tension. The discussion transitions to fluid dynamics with the continuity equation for incompressible flow and concludes with Bernoulli's equation, including its application to flow in pipes and the principle of aircraft lift.
π Lecture Summary
1. A fluid is matter that has no definite shape
A fluid, including both gases and liquids, adjusts to the shape of its container. All fluids are composed of molecules that attract each other.
2. Liquids exhibit surface tension
A liquid's free surface tends to contract to the minimum possible area, indicating a state of tension. This arises from cohesive forces, the attractive forces between molecules of the liquid. Deep inside the liquid, a molecule experiences equal forces from all directions, resulting in no net force. At the surface, a molecule is surrounded by only half as many molecules (since there are none above), leading to a net inward force.
3. The force of contraction
The surface tension, denoted by Ξ³ (gamma), is the force of contraction per unit length acting at right angles to an imaginary line on the liquid's surface. It is defined as Ξ³ = F / L, where F is the force exerted by the liquid's "skin" along a line of length L. The SI unit of surface tension is N/m.
4. Quantitative measurement of surface tension
In a setup with a soap film on a wire frame and a sliding wire of weight w, the force T pulls the wire downward. The net downward force is F = w + T. As the film has both a front and back surface, this force acts along a total length of 2L. Therefore, surface tension is: Ξ³ = F / (2L) β F = 2Ξ³L Hence, the surface tension is Ξ³ = (w + T) / (2L).
5. Work done to stretch the skin of a liquid
When the sliding wire is moved by a displacement Ξx, the work done is FΞx. This is a conservative force, so the change in potential energy is ΞU = FΞx = 2Ξ³LΞx. The product LΞx equals the change in surface area, ΞA. Thus, Ξ³ = ΞU / ΞA. This demonstrates that surface tension is the surface potential energy per unit area.
7. Surface tension and pressure differences
Surface tension causes a pressure difference between the inside and outside of a soap bubble or a liquid drop. A soap bubble has two spherical surfaces with a thin liquid layer between. For a bubble of radius r, the net force due to surface tension is 2(2ΟrΞ³). In equilibrium, the forces are equal, leading to an excess pressure of p β pβ = 4Ξ³ / r. For a liquid drop, which has only one surface, the excess pressure is p β pβ = 2Ξ³ / r.
π‘ Why this matters: This explains why smaller soap bubbles have higher internal pressure than larger ones.
8. Continuity Equation
Since liquids are incompressible, equal volumes must flow through different sections of a pipe in the same time. This gives Vβ = Vβ. As volume V = A * L = A * v * t, we have Aβvβt = Aβvβt, simplifying to Aβvβ = Aβvβ. This means the fluid flows faster where the tube is narrower and slower where it is wider.
9. Bernoulli's Equation
For a steadily flowing fluid, Bernoulli's equation states: p + (1/2)ΟvΒ² + Οgy = constant This equation relates pressure (p), kinetic energy per unit volume ((1/2)ΟvΒ²), and gravitational potential energy per unit volume (Οgy).
π Definition β Bernoulli's Equation: The sum of the pressure, kinetic energy per unit volume, and gravitational potential energy per unit volume is constant along a streamline for an ideal fluid.
π Formula: pβ + (1/2)ΟvβΒ² + Οgyβ = pβ + (1/2)ΟvβΒ² + Οgyβ β The pressure energy plus kinetic energy plus potential energy per unit volume is constant.
10. Application of Bernoulli's Equation
For water flowing in a horizontal pipe where the cross-section decreases (yβ = yβ), Bernoulli's equation simplifies to: pβ + (1/2)ΟvβΒ² = pβ + (1/2)ΟvβΒ² Using the continuity equation Aβvβ = Aβvβ, we find: vβ = (Aβ/Aβ)vβ and therefore: pβ = pβ β (1/2)Ο(vβΒ² β vβΒ²)
This shows pressure is smaller where the fluid flows faster.
π‘ Why this matters: This principle explains how aircraft achieve lift. The wing shape is curved, causing air to move faster over the top than the bottom. The lower pressure on top and higher pressure below creates a net upward force called lift.
π Example β Aircraft Lift: Air moves faster over the curved top of an aircraft wing than the flatter bottom. According to Bernoulli's principle, the faster-moving air on top exerts less pressure than the slower air below. This pressure difference results in a net upward force, lifting the aircraft.
β Key Takeaways
Surface tension is a property of liquids that causes the surface to contract, defined as force per unit length and also as surface potential energy per unit area. The pressure inside a soap bubble (4Ξ³/r) is double that inside a liquid drop (2Ξ³/r) due to the bubble having two surfaces. For incompressible fluid flow, the continuity equation Aβvβ = Aβvβ states that flow speed increases as the tube's cross-sectional area decreases. Bernoulli's equation, p + (1/2)ΟvΒ² + Οgy = constant, is a statement of energy conservation for flowing fluids, explaining that where flow speed is high, pressure is low, which is the fundamental principle behind aircraft lift.
π§ Quick Revision Questions
- What is the definition of surface tension, and what are its two equivalent forms?
- Why does the pressure inside a soap bubble differ from that inside a liquid drop of the same radius?
- A liquid flows from a wide pipe of diameter 4 cm into a narrow pipe of diameter 2 cm. If the speed in the wide pipe is 1 m/s, what is the speed in the narrow pipe? (Assume incompressible flow)
- State Bernoulli's equation for an ideal fluid and explain the physical meaning of each term.
- How does Bernoulli's principle explain the generation of lift on an aircraft wing?
π Lecture 19 β PHYSICS OF SOUND
π Overview: This lecture introduces the physics of sound waves, which are longitudinal oscillations of density that carry energy. It covers how sound intensity is measured in decibels, the mathematical description of sound waves, and the Doppler Effect, which explains why the frequency of sound changes when the source or observer is in motion.
ποΈ Topics Covered
Sound waves as longitudinal density oscillations with measurable intensity using decibels; the mathematical wave equation for density including wavelength, time period, frequency, wavenumber, and angular frequency; and the Doppler Effect with three cases: moving observer with source at rest, moving source with observer at rest, and both moving simultaneously.
π Lecture Summary
1. Sound Waves and Intensity
Sound waves correspond to longitudinal oscillations of density. As sound waves move, you find the density of air greater in some places (compressions) and less in others (rarefactions). Sound waves carry energy. The minimum energy that humans can hear is about 10β»ΒΉΒ² watts per cmΒ³, which is called the threshold of hearing (Iβ).
π‘ Why this matters: Understanding that sound is a density wave helps explain why you can hear around corners (diffraction) and why sound travels at different speeds through different materials.
2. Decibels (Intensity Measurement)
To measure the intensity of sound, we use decibels (db) as the unit. Decibels are a relative measure to compare the intensity of different sounds with one another.
π Definition β Intensity Level (R) in decibels: R = 10 logββ (I / Iβ) where I is the intensity of the sound and Iβ is the threshold of hearing (10β»ΒΉΒ² W/cmΒ³).
π Example: On a street without traffic, the sound level is about 30 db. A pressure horn creates about 90 db. Serious ear damage happens around 120 db.
3. Mathematical Description of a Sound Wave
A sound wave moving in the x-direction with speed v is described by: Ο(x, t) = Οβ sin [2Ο/Ξ» (x β vt)] where Ο(x, t) is the density of air at a point x at time t.
a) Constant Phase Motion: Suppose as time t increases, we move in such a way as to keep (x β vt) constant. To keep the density Ο(x, t) constant, we would have to move with the speed of sound, i.e., v.
b) Wavelength (Ξ»): In the expression for Ο(x, t), replace x by x + Ξ». Nothing changes because sin[2Ο/Ξ» (x + Ξ» β vt)] = sin[2Ο/Ξ» (x β vt)]. This is why we call Ξ» the wavelength, meaning the length after which a wave repeats itself.
c) Time Period (T) and Frequency (Ξ½): Replace t by t + T where T = Ξ»/v. Nothing changes. T is called the time period of the sound wave, meaning the time after which it repeats itself. The frequency is the number of cycles per second and is related to T through Ξ½ = 1/T.
d) Wavenumber (k) and Angular Frequency (Ο):
π Definition β Wavenumber: k = 2Ο/Ξ»
π Definition β Angular Frequency: Ο = 2Ο/T = 2ΟΞ½
4. Doppler Effect
The Doppler Effect describes how relative motion between source and observer causes the observer to receive a frequency different from that emitted by the source. One must distinguish between two cases.
Case 1: Moving Observer, Source at Rest: If the observer was at rest, the number of waves received in time t would be t/T (or vt/Ξ»). If she is moving towards the source with speed vβ, the additional number of waves received is vβt/Ξ».
π Definition β Doppler Formula (Moving Observer): Ξ½' = (v + vβ)/Ξ» = (v + vβ)/(v/Ξ½) = Ξ½ (v + vβ)/v
Conclusion: As the observer runs towards the source, she hears a higher frequency (higher pitch).
Case 2: Moving Source, Observer at Rest: As the source runs towards the observer, more waves must be packed together. Each wavelength is reduced by vβ/Ξ½.
π Definition β Doppler Formula (Moving Source): The wavelength seen by the observer is Ξ»' = (v β vβ)/Ξ½. The frequency heard is Ξ½' = v/Ξ»' = v / [(v β vβ)/Ξ½] = Ξ½ [v / (v β vβ)]
Case 3: Moving Source and Moving Observer: The general formula combines both effects.
π Definition β General Doppler Formula: Ξ½' = Ξ½ [(v + vβ) / (v β vβ)]
The above two results are special cases of this formula.
β Key Takeaways
Sound waves are longitudinal density oscillations measurable in decibels using a logarithmic scale relative to the threshold of hearing. The mathematical wave equation uses wavelength, time period, frequency, wavenumber, and angular frequency. The Doppler Effect formula changes depending on whether the observer, source, or both are moving; the general formula is Ξ½' = Ξ½[(v + vβ)/(v β vβ)], where the observer moving toward the source and the source moving toward the observer both increase the observed frequency. Understanding decibels is crucial for hearing safety (120 db causes ear damage).
π§ Quick Revision Questions
- What is the threshold of hearing in watts per cmΒ³, and what is it called?
- If a sound has an intensity of 10β»βΆ W/cmΒ³, what is its intensity level in decibels?
- What happens to the density wave if you replace x by x + Ξ» in the wave equation Ο(x, t) = Οβ sin[2Ο/Ξ» (x β vt)]?
- A police siren emitting 800 Hz is moving toward you at 30 m/s. If the speed of sound is 340 m/s, what frequency do you hear?
- If both source and observer are moving, which formula correctly gives the observed frequency?