📘 Lecture 29 — ALTERNATING CURRENT
📖 Overview: This lecture introduces alternating current (AC) — its sinusoidal nature, generation, and key properties such as root mean square values. It then explores practical applications like transformers and fundamental circuit elements: self-inductance, the behavior of LR circuits, the energy stored in an inductor, and the oscillations in an LC circuit. Understanding AC is essential for analyzing household electricity, power transmission, and resonant circuits.
🗂️ Topics Covered
The lecture begins by defining alternating current and deriving its root mean square (RMS) value. It explains how AC is generated by a rotating coil in a magnetic field. Next, it covers the principle and types of transformers, including the relationship between voltage/current and the number of turns in the primary and secondary coils. The concept of self-inductance is introduced, including its calculation for a solenoid. The response of a circuit containing an inductor and resistor (LR circuit) when connected to a battery is analyzed. The energy stored in a magnetic field within an inductor is derived. Finally, the lecture examines electromagnetic oscillations in an LC circuit.
📝 Lecture Summary
1. Alternating Current (AC)
AC is current that periodically reverses direction, most commonly following a sinusoidal function for both current and voltage. The average value of a pure sine wave over one complete cycle is zero because it spends equal time in the positive and negative directions. However, the square of a sine wave is always positive, so its average is not zero. The average of the square is half the square of the peak value.
🔑 Definition — Root Mean Square (rms) Value: The effective value of an AC quantity, equivalent to the DC value that would produce the same heating effect in a resistor. For a sinusoidal wave, rms = peak value / √2.
📐 Formula: I_rms = I_m / √2 and ε_rms = ε_m / √2 → The RMS current is the peak current divided by the square root of 2.
📌 Example: For a current with a peak value of 1 unit, sin²(ωt) over a period T averages to 1/2. Taking the square root gives I_rms = 1/√2 ≈ 0.707 * I_m.
2. AC Generation
An AC generator produces an alternating emf by rotating a coil of area A in a constant magnetic field B with angular frequency ω. The magnetic flux through the coil changes sinusoidally with time as Φ = BA cos(ωt).
🔑 Definition — Induced Emf in a Generator: ε = ε_m sin ωt, where ε_m = BAω is the peak induced emf.
📐 Formula: ε = BAω sin ωt → The induced emf is directly proportional to the magnetic field strength, the area of the coil, and the angular frequency of rotation.
3. Transformers
Transformers are devices that step voltage up or down using electromagnetic induction. They consist of a primary coil (N_p turns) and a secondary coil (N_s turns) wrapped around a common iron core. The ratio of the secondary voltage (ε_s) to the primary voltage (ε_p) is equal to the ratio of the number of turns.
🔑 Definition — Step-up Transformer: A transformer where N_s > N_p, resulting in a secondary voltage higher than the input voltage. Conversely, a Step-down Transformer has N_s < N_p, producing a lower secondary voltage.
📐 Formula: ε_p / ε_s = N_p / N_s → The voltage ratio is directly proportional to the turn ratio. In an ideal (lossless) transformer, input power equals output power, ε_p I_p = ε_s I_s.
📐 Formula: I_s / I_p = N_p / N_s → The current ratio is inversely proportional to the turn ratio.
4. Self-Inductance
Self-inductance (L) is the property of a coil by which a change in the current through it induces an emf in the same coil. The magnetic flux Φ through the coil is proportional to the current I: Φ = LI.
🔑 Definition — Inductance (L): The constant of proportionality relating the magnetic flux through a coil to the current flowing through it. Its SI unit is the Henry (H), where 1 H = 1 T·m²/A. Inductance is a geometric property, dependent only on the coil's shape and size.
📐 Formula: L = (NΦ_B) / I → The inductance of a coil is the total flux linkage per unit current.
📌 Example: The self-inductance of a solenoid of length l, area A, and n turns per unit length is calculated as follows. The flux through N (= n*l) turns is NΦ_B = (n*l) * (μ₀ n I) * A = μ₀ n² I l A. Therefore, L = μ₀ n² l A.
📌 Example: Find the inductance of a coil with 3500 turns, length 10 cm, and radius 5 cm. Using L = μ₀ N² A / l:
L = (4π × 10⁻⁷ T·m/A) * (3500)² * (π*(0.05 m)²) / (0.10 m) = 1.21 H.
5. LR Circuit
When a resistor (R) and an inductor (L) are connected in series to a battery of emf ε, Kirchhoff's loop rule gives: ε = IR + L (dI/dt). The solution shows that the current does not rise to its final value I_0 = ε/R instantly but grows gradually.
🔑 Definition — Time Constant (τ): The time required for the current in an LR circuit to reach approximately 63% of its maximum value. It is the characteristic time for the circuit to respond.
📐 Formula: τ = L / R → The time constant is the ratio of inductance to resistance. [τ] = Henry/Ohm = second.
📐 Formula: I(t) = (ε/R)[1 - e^(-t/τ)] → The current increases exponentially from 0 to ε/R. The time constant τ determines the speed of this rise.
6. Energy Stored in an Inductor
To establish a current I in an inductor, work must be done against the induced emf. The power supplied is P = ε I = L (dI/dt) I. This work is stored as energy (U_B) in the inductor's magnetic field.
🔑 Definition — Energy in an Inductor: U_B = (1/2) L I² → This is the energy required to create the current I and is analogous to the energy (1/2)CV² stored in a capacitor.
📌 Example: For a solenoid, substituting L = μ₀ n² l A and B = μ₀ n I into the energy formula gives U_B = (1/2) μ₀ n² l A (B / μ₀ n )² = B²/(2μ₀) * (lA). The energy density, or energy per unit volume, in a magnetic field is u_B = B² / (2 μ₀).
7. LC Oscillations
An LC circuit consists of an inductor (L) and a capacitor (C) connected together. If the capacitor is initially charged, it will discharge through the inductor, creating a current. Energy is exchanged between the electric field of the capacitor and the magnetic field of the inductor. In the absence of resistance, the total energy U = (1/2) L I² + (1/2) q²/C remains constant.
🔑 Definition — Angular Frequency of LC Oscillation: The charge, current, and voltage in an ideal LC circuit oscillate sinusoidally with an angular frequency ω, given by ω = 1 / √(LC). This is the natural frequency of the circuit.
📐 Formula: q = q_m cos(ωt), where q_m is the maximum charge on the capacitor and ω = 1/√(LC). The current I = dq/dt = -ω q_m sin(ωt).
💡 Why this matters: This oscillation will continue forever if there is no resistance (R=0). This concept is the foundation for radio transmitters and receivers, where a circuit is tuned to resonate at a specific frequency.
⭐ Key Takeaways
The most crucial students must remember are the calculation of RMS values (peak/√2) and their role in representing AC power. The definition and calculation of self-inductance, particularly for a solenoid (L = μ₀ n² l A), is fundamental. The behavior of an LR circuit, including the time constant τ = L/R and the exponential rise of current, is a key dynamic concept. The energy stored in an inductor is U = ½ L I², directly comparable to the capacitor's stored energy. Finally, the condition for oscillations in an LC circuit is ω = 1/√(LC), leading to a continuous exchange of energy between the inductor and capacitor.
🧠 Quick Revision Questions
- Why is the average value of a sinusoidal AC current zero over one full cycle, but its RMS value is not zero? How is the RMS current related to the peak current?
- Derive the self-inductance
Lof a long solenoid in terms of its number of turns, length, and cross-sectional area. - A step-down transformer has 500 turns on its primary and 100 turns on its secondary. If the primary voltage is 120 V, what is the secondary voltage?
- In an LR circuit, what is the time constant, and what percentage of the maximum current has it reached after one time constant has elapsed?
- An LC circuit consists of a 0.1 H inductor and a 10 µF capacitor. Calculate the angular frequency of oscillation for the charge on the capacitor.
📘 Lecture 30 — ELECTROMAGNETIC WAVES
📖 Overview: This lecture explains how James Clerk Maxwell unified electricity and magnetism into a single theory, predicted electromagnetic waves, and established the foundations of modern optics and communications. It covers Maxwell's correction to Ampere's law, the full set of Maxwell's equations, the properties and production of electromagnetic waves, and the concepts of polarization.
🗂️ Topics Covered
The lecture begins by reviewing the four known laws of electromagnetism before Maxwell and the inconsistency Maxwell discovered in Ampere's law regarding conservation of charge. It then introduces Maxwell's modification via the displacement current, presents the complete Maxwell's equations, discusses the properties and speed of electromagnetic waves, explains wave propagation in free space, emission from antennas, reception principles, and ends with polarization and polarizers.
📝 Lecture Summary
1. Before the investigations of James Clerk Maxwell around 1865, the known laws of electromagnetism were:
The lecture lists the four classical laws: Gauss's law for electricity, Gauss's law for magnetism, Faraday's law of induction, and the original Ampere's law. These laws describe how electric and magnetic fields behave with charges, currents, and each other.
🔑 Gauss's law of electricity: $\oint \vec{E} \cdot d\vec{A} = \frac{q}{\varepsilon_0}$ (integral over any closed surface) — the net electric flux through a closed surface equals the enclosed charge divided by permittivity.
🔑 Gauss's law of magnetism: $\oint \vec{B} \cdot d\vec{A} = 0$ (integral over any closed surface) — magnetic monopoles do not exist; net magnetic flux through any closed surface is zero.
🔑 Faraday's law of induction: $\oint \vec{E} \cdot d\vec{s} = -\frac{d\Phi_B}{dt}$ (integral over any closed loop) — a changing magnetic field induces an electric field.
🔑 Ampere's law: $\oint \vec{B} \cdot d\vec{s} = \mu_0 I$ (integral over any closed loop) — a current produces a magnetic field.
2. But Maxwell realized that the above 4 laws were not consistent with the conservation of charge, which is a fundamental principle.
Maxwell identified an inconsistency: applying Ampere's law to different surfaces bounded by the same loop gives different results. For a capacitor charging in a circuit, surfaces 1, 2, and 4 (which intercept the wire) give one result, but surface 3 (which passes between the capacitor plates) gives a different result because no current flows between the plates. This violates the principle that magnetic field should be independent of the surface chosen.
Maxwell modified Ampere's law as follows: $\oint \vec{B} \cdot d\vec{s} = \mu_0 (I + I_d)$ where the displacement current is $I_d = \varepsilon_0 \frac{d\Phi_E}{dt}$.
The current in the circuit is $I = \frac{dQ}{dt}$. The charge on a capacitor plate is $Q = \varepsilon_0 EA$. Hence, $I = \frac{d}{dt}(\varepsilon_0 EA) = \varepsilon_0 \frac{d(EA)}{dt} = \varepsilon_0 \frac{d\Phi_E}{dt} \equiv I_D$. In words, the changing electric field in the gap acts as a source of the magnetic field in just the same way as the current in the outside wires.
💡 Why this matters: A magnetic field may have two separate reasons for existence — flowing charges or changing electric fields. This was Maxwell's crucial insight.
3. The famous Maxwell's equations are as follows:
The complete set of four equations: a) $\oint \vec{E} \cdot d\vec{S} = \frac{Q}{\varepsilon_0}$ (Gauss's law for electricity) b) $\oint \vec{E} \cdot d\vec{\ell} = -\frac{d\Phi_B}{dt}$ (Faraday's law) c) $\oint \vec{B} \cdot d\vec{S} = 0$ (Gauss's law for magnetism) d) $\oint \vec{B} \cdot d\vec{\ell} = \mu_0 (I + \varepsilon_0 \frac{d\Phi_E}{dt})$ (Ampere-Maxwell law)
Together with the Lorentz Force $\vec{F} = q(\vec{E} + \vec{v} \times \vec{B})$, they provide a complete description of all electromagnetic phenomena, including waves.
4. Electromagnetic waves were predicted by Maxwell and experimentally discovered many years later by Hertz.
Key properties of electromagnetic waves: a) Absolutely no medium is required — they travel through vacuum. b) The speed of propagation is $c$ for all waves in the vacuum, where $c = 3.0 \times 10^8$ m/s. c) There is no limit to the amplitude or frequency.
📌 Example: Red light has $\lambda = 700$ nm. The frequency $\nu$ is calculated: $\nu = \frac{3.0 \times 10^8 \text{ m/s}}{7 \times 10^{-7} \text{ m}} = 4.29 \times 10^{14}$ Hertz. By comparison, microwaves have wavelength ~6 cm, radio waves are meters long, while X-rays and gamma-rays have wavelengths the size of atoms or smaller.
5. We now consider how electromagnetic waves can travel through empty space.
An electromagnetic wave propagates via a chain of events: a changing electric field creates a changing electric flux ($\frac{d\Phi_E}{dt}$), which through $\oint \vec{B} \cdot d\vec{s} = \mu_0 \varepsilon_0 \frac{d\Phi_E}{dt}$ creates a changing magnetic field. This changing magnetic field creates a changing magnetic flux ($\frac{d\Phi_B}{dt}$), which through $\oint \vec{E} \cdot d\vec{s} = -\frac{d\Phi_B}{dt}$ creates a changing electric field. This cycle continues, allowing propagation in free space.
For a wave moving in the z direction, the electric field is in the x direction: $E_x = E_0 \sin(kz - \omega t)$, and the magnetic field is perpendicular to it: $B_y = B_0 \sin(kz - \omega t)$.
📐 Wave relation: $\omega = kc$, where $\omega$ is angular frequency and $k$ is wave number.
📐 Amplitude relation: $E_0 = c B_0$ — the electric and magnetic field amplitudes are related by the speed of light. The two fields are in phase with each other.
6. The production of electromagnetic waves is done by forcing current to vary rapidly in a small piece of wire.
In devices like mobile phones, circuits produce a high frequency current that goes into a dipole antenna (two small pieces of conductor). The rapidly changing electric field between the two oppositely charged pieces creates a magnetic field. Both fields propagate outwards, with amplitude falling as $1/r$.
📐 Power radiation pattern: $I(\theta) \propto \frac{\sin^2 \theta}{r^2}$. The $\sin^2 \theta$ dependence shows that power is radiated unequally as a function of direction. Maximum power is at $\theta = \pi/2$ and least at $\theta = 0$.
7. The reception of electromagnetic waves requires an antenna.
An incoming wave has an electric field that forces electrons to run up and down the antenna wire, producing a tiny electric current. This current is then amplified electronically. A variable capacitor is used to tune to different frequencies.
8. As we have seen, the electric field of a wave is perpendicular to the direction of its motion.
If the electric field has a fixed direction (say, $\hat{x}$), the wave is polarized in the x direction. Most sources (candle, sun, light bulb) produce unpolarized light — there is no definite direction of the electric field, no definite phase between orthogonal components, and atomic dipoles are randomly oriented.
For a linearly polarized plane wave at an angle $\theta$ relative to $\hat{x}$: $E_x = E_0 \cos\theta \cdot \sin(kz - \omega t)$, $E_y = E_0 \sin\theta \cdot \sin(kz - \omega t)$, $E_z = 0$.
9. Electromagnetic waves from an unpolarized source can be polarized by passing them through a simple polarizer.
A polarizer (e.g., a metal plate with slits) allows only the electric field component perpendicular to the slits to pass. This process produces linearly polarized waves from unpolarized ones. The process of converting an unpolarized source into a polarized source is known as polarization.
⭐ Key Takeaways
Maxwell's crucial contribution was adding the displacement current term ($\varepsilon_0 d\Phi_E/dt$) to Ampere's law, which resolved an inconsistency with charge conservation and predicted that changing electric fields generate magnetic fields. This led to the complete set of Maxwell's equations, which unified electricity, magnetism, and optics and predicted electromagnetic waves traveling at speed $c$ with no medium required. Electromagnetic waves have electric and magnetic fields perpendicular to each other and to the direction of motion, with amplitudes related by $E_0 = cB_0$. These waves can be produced by oscillating currents in antennas, received by antennas that convert the wave's electric field into electrical signals, and can be polarized to select a specific direction of the electric field.
🧠 Quick Revision Questions
- What inconsistency did Maxwell find in the original Ampere's law when applied to a charging capacitor?
- What is the displacement current, and how does it resolve the inconsistency?
- Write down all four Maxwell's equations in integral form and explain each term.
- How are the electric and magnetic field amplitudes related in an electromagnetic wave?
- What does it mean for an electromagnetic wave to be polarized, and how can you polarize unpolarized light?
📘 Lecture 31 — LIGHT
📖 Overview: This lecture introduces the fundamental properties of light, including its finite speed, its nature as an electromagnetic wave, and the principles governing its behavior. It covers light's interaction with matter, including reflection, refraction, and total internal reflection, with applications in fiber optics.
🗂️ Topics Covered
The lecture covers the speed of light and its historical measurement, the electromagnetic spectrum and visible light, color perception and spectra, Fermat's Principle as applied to reflection, Snell's Law derived from Fermat's Principle for refraction, total internal reflection, and fiber optic cables.
📝 Lecture Summary
1. Light travels very fast but its speed is not infinite.
Early attempts to measure the speed of light using earth-based experiments failed. In 1675, astronomer Roemer studied the timing of eclipses of Jupiter's moon Io. By observing Io from Earth at points A and C, he found the eclipse was 16.6 minutes late, which is the time for light to travel the distance AC. Roemer estimated the speed of light, c, as 3×10⁸ metres/sec, remarkably close to the modern value of c = 299792458.6 metres/sec.
2. Light is electromagnetic waves.
Different frequencies (ν) correspond to different colours, and equivalently, different wavelengths (λ) correspond to different colours. The product of frequency and wavelength equals the speed of light: ν × λ = c. Visible light is only one small part of the total electromagnetic spectrum. Here, nm means nanometres or 10⁻⁹ metres.
3. If light contained all frequencies with equal strength, it would appear as white to us.
Most things appear coloured because they radiate more strongly in one range of frequency than others. If there is more intensity in the yellow range than the green range, we see mostly yellow. The sky appears blue because tiny dust particles high in the atmosphere reflect a lot of the blue light coming from the sun. The spectrum of normal daylight shows a hump at smaller wavelengths, while the spectrum from a tungsten bulb is smoother with yellow dominating.
4. What path does light travel upon?
If there is no obstruction, light travels on a straight line, the shortest path between two points. Fermat's Principle states that in all situations, light will always take that path for which it takes the least time. For light reflected from a mirror, the total distance travelled by the ray is L = √(a² + x²) + √(b² + (d−x)²). The time taken is t = L/c. To find the smallest time, differentiate and set the derivative to zero. This derivation shows that the angle of reflection (θ₁) equals the angle of incidence (θ₁').
🔑 Definition — Fermat's Principle: Light always takes the path that requires the least time to travel.
📐 Formula: t = L/c → The time taken for light to travel a distance L at speed c.
📌 Example: For a mirror, the total path length is L = √(a² + x²) + √(b² + (d−x)²). Minimizing time by setting dt/dx = 0 leads to sinθ₁ = sinθ₁', meaning the angle of incidence equals the angle of reflection.
5. The speed of light in vacuum is a fixed constant of nature called c.
In a medium, light can travel slower or faster than c. The refractive index of a medium is defined as: Refractive index = Speed of light in vacuum / Speed of light in material (or n = c/v). Usually, values of n are greater than one (e.g., for glass it is around 1.5), but in some special media, its value can be less than one. The value of n also depends on the wavelength (or frequency) of light, which is called dispersion. This means different colours travel at different speeds inside a medium, causing white light to get separated into different colours when passing through a glass prism.
🔑 Definition — Refractive index (n): The ratio of the speed of light in vacuum to the speed of light in a material, n = c/v.
🔑 Definition — Dispersion: The dependence of refractive index on wavelength (or frequency), causing different colours to travel at different speeds in a medium.
📌 Example: In a glass prism, blue light travels faster than red light, which is responsible for the separation of white light into its constituent colours.
6. We can apply Fermat's Principle to find the path followed by a ray of light when it goes from one medium to another.
Part of the light is reflected, and part is refracted, bending away or toward the normal. The total time is t = L₁/v₁ + L₂/v₂. Using n = c/v, this becomes t = (n₁L₁ + n₂L₂)/c. Fermat's Principle says the time must be minimized: 0 = dt/dx = (1/c)(dL/dx). This derivation leads to Snell's Law: n₁ sinθ₁ = n₂ sinθ₂.
📐 Formula: Snell's Law: n₁ sinθ₁ = n₂ sinθ₂ → The product of refractive index and the sine of the angle with respect to the normal is constant across the interface between two media.
📌 Example: Light travels from air (n₁ ≈ 1) into water (n₂ ≈ 1.33). If the angle of incidence is 30°, then sinθ₂ = (1/1.33) × sin30° = 0.376, so θ₂ ≈ 22°, meaning the light bends toward the normal.
7. Light coming from air into water bends toward the normal. Conversely, light from a source in the water will bend away from the normal.
If you keep increasing the angle with respect to the normal so that the light bends and begins to just follow the surface, this phenomenon is called total internal reflection, and θc is called the critical angle. It obeys: n₁ sinθc = n₂ sin90°, from which θc = sin⁻¹(n₂/n₁).
🔑 Definition — Total internal reflection: The phenomenon where light is completely reflected back into a medium when it strikes the boundary at an angle greater than the critical angle.
🔑 Definition — Critical angle (θc): The angle of incidence for which the angle of refraction is 90°, given by θc = sin⁻¹(n₂/n₁).
📐 Formula: n₁ sinθc = n₂ → sinθc = n₂/n₁ → θc = sin⁻¹(n₂/n₁)
📌 Example: For light traveling from glass (n₁ = 1.5) to air (n₂ = 1.0), the critical angle is θc = sin⁻¹(1.0/1.5) = sin⁻¹(0.667) ≈ 41.8°.
💡 Why this matters: Total internal reflection is the principle behind fiber optic cables, which now carry thousands of telephone calls in a cable whose diameter is only a little bigger than a human hair!
8. Fibre optic cables, which are now common everywhere, make use of the total internal reflection principle to carry light.
Even if the cable is bent, the light will continue to travel along it. The glass inside the cable must have exceedingly good consistency—if it is thicker or thinner in any part, the refractive index will become non-uniform and a lot of light will get lost.
⭐ Key Takeaways
The speed of light is finite (c = 3×10⁸ m/s) and was first accurately measured by Roemer using Jupiter's moon Io. Light behaves as an electromagnetic wave, and different wavelengths correspond to different colours. Fermat's Principle—that light takes the path of least time—is a powerful concept that explains both reflection (law of reflection) and refraction (Snell's Law). Snell's Law (n₁ sinθ₁ = n₂ sinθ₂) governs how light bends when moving between media, and when light moves from a higher to a lower refractive index, total internal reflection can occur beyond the critical angle. This principle is the basis for fiber optic technology, where light is guided along thin glass cables even when bent.
🧠 Quick Revision Questions
- Who first accurately measured the speed of light, and what astronomical observation did they use?
- What is the relationship between frequency, wavelength, and the speed of light?
- State Fermat's Principle and explain how it leads to the law of reflection.
- Write Snell's Law and explain what happens to light when it passes from a medium with higher refractive index to one with lower refractive index.
- What is total internal reflection, and how is the critical angle calculated? Give one practical application.
📘 Lecture 32 — INTERACTION OF LIGHT WITH MATTER
📖 Overview: This lecture explores the four fundamental ways light interacts with matter: emission, absorption, transmission, and reflection. It covers blackbody radiation, Wien's Law, and the Stefan-Boltzmann Law, along with emission and absorption spectra, polarization, and birefringence, which are essential for understanding phenomena from star temperatures to LCD displays.
🗂️ Topics Covered
The lecture covers the four basic interactions of light with matter (emission, absorption, transmission, reflection), blackbody radiation and its continuous spectrum, Wien's Law for peak wavelength determination, the Stefan-Boltzmann Law for radiated power, application to finding planetary temperatures, discrete emission spectra for elements, absorption spectra, polarization of light, and birefringent materials used in liquid crystal displays.
📝 Lecture Summary
1. Introduction: Four Basic Interactions
Light interacts with matter in four fundamental ways: emission (matter releases energy as light), absorption (matter takes energy from light), transmission (matter allows light to pass through it), and reflection (matter repels light in another direction).
2. Blackbody Radiation
When an object is heated (e.g., an iron rod or tungsten filament), it emits light. At ~800°C it is red hot; at ~2500°C it is yellowish-white. Below 800°C, infrared (IR) light is emitted but invisible to the eye. This continuous emission of all wavelengths is called blackbody radiation. The peak of the emitted energy shifts to smaller wavelengths (higher frequencies) as temperature increases. Temperature is measured in Kelvin (°K), where °K = °C + 273.
3. Wien's Law
Wien's Law states the relationship between the peak wavelength (λ) and temperature (T): 🔑 Definition — Wien's Law: The peak wavelength of blackbody radiation is inversely proportional to the temperature. 📐 Formula: λT = 2.90 × 10⁻³ m·K → The product of peak wavelength (in meters) and temperature (in Kelvin) is constant. 📌 Example: For the Sun with T ≈ 5800 K, λ = (2.90 × 10⁻³) / 5800 ≈ 5.0 × 10⁻⁷ m (500 nm, visible yellow-green). 💡 Why this matters: Wien's Law allows astronomers to determine a star's temperature from its brightest wavelength.
🔑 Definition — Blackbody radiation: Electromagnetic radiation emitted by a heated body, with a continuous spectrum whose peak depends on temperature. It arises from accelerated charges (electrons, atoms, molecules) in random motion, even in an empty box due to its sides.
4. When to Apply Wien's Law
Wien's Law applies only to objects that emit light (not those that merely reflect it, like flowers). The Sun and other stars obey Wien's Law because their gases emit radiation in equilibrium with other materials. Astronomers use this to determine star temperatures.
5. Stefan-Boltzmann Law
🔑 Definition — Stefan-Boltzmann Law: The power radiated per unit area of a hot body is proportional to the fourth power of its absolute temperature. 📐 Formula: P = σT⁴, where σ = 5.67 × 10⁻⁸ W·m⁻²·K⁻⁴ (Stefan-Boltzmann constant). 💡 Why this matters: Hotter objects radiate significantly more energy (doubling temperature increases power by 16×).
6. Application: Finding a Planet's Temperature
For a planet at distance R from the Sun (temperature T_sun, radius R_sun), in equilibrium:
- Energy radiated by Sun: σT_sun⁴ × 4πR_sun²
- Energy received per unit area on planet: (σT_sun⁴ × 4πR_sun²) × (1/(4πR²))
- This must equal energy radiated per unit area by planet: σT_planet⁴
- Therefore: σT_planet⁴ = σT_sun⁴ × (R_sun²/R²) 📐 Formula: T_planet = T_sun × √(R_sun / (2R))
7. Emission Spectra
While blackbody radiation has a continuous spectrum, excited gas of identical atoms emits only a few discrete wavelengths. Each chemical element produces a distinct pattern of colors called an emission spectrum. For example, hydrogen gas lamps emit 3 visible lines, uniquely identifying hydrogen — like a "thumbprint."
🔑 Definition — Emission spectrum: A pattern of specific, discrete wavelengths of light emitted by excited atoms of a particular element.
8. Exciting Atoms
Atoms can be excited to reveal their identity by heating materials containing them. Different materials sprinkled on a flame produce different colors, demonstrating distinct emission spectra.
9. Absorption Spectra
Emission and absorption are complementary. When white light (containing all frequencies) passes through hydrogen gas, all wavelengths survive except those matching hydrogen's emission lines. Thus, the absorption spectrum looks identical to the emission spectrum — the same lines are absorbed as are emitted. This reveals hydrogen clouds in outer space.
10. Atmospheric Absorption
The atmosphere contains gases (oxygen, nitrogen, ozone, water) that absorb light at many wavelengths, each with their own absorption spectra, just as atoms have.
11. Selective Absorption and Color
All perceived colors result from selective absorption by molecules of certain frequencies. For example, carotene (in carrots, tomatoes, sarson) absorbs blue light, making them appear orange/red/yellow. Chlorophyll (in leaves) absorbs red and blue light, making leaves appear green.
12. Polarization
Light is an electromagnetic wave with an electric field vector perpendicular to travel direction. If this vector points in a definite direction, the wave is polarized; otherwise, it is unpolarized. Unpolarized light (e.g., from a flame) can be polarized by passing through a polarizer, which transmits only the component along a specific axis. Each wave is reduced in amplitude by cosθ and in intensity by cos²θ.
🔑 Definition — Polarized light: Light whose electric field vector oscillates in a single, definite direction.
13. Birefringent Materials and LCDs
Birefringent materials have different optical properties in the two transverse directions, designed using crystals or stressed plastics. They are used in liquid crystal displays (LCDs) in watches and mobile phones. Birefringence occurs in materials with structural asymmetry (more "springy" in one direction than another).
⭐ Key Takeaways
Blackbody radiation is continuous, with its peak shifting to shorter wavelengths at higher temperatures (Wien's Law: λT = 2.90 × 10⁻³ m·K). The Stefan-Boltzmann Law (P = σT⁴) quantifies power radiated per unit area, allowing calculation of planetary temperatures from solar parameters. Elements have unique, discrete emission and absorption spectra — key for identifying substances like hydrogen. Polarization describes the direction of the electric field vector, and polarization reduces intensity by cos²θ. Birefringent materials with asymmetric optical properties are essential for LCD technology.
🧠 Quick Revision Questions
- What are the four basic ways light interacts with matter?
- State Wien's Law and explain what it allows astronomers to determine.
- Write the Stefan-Boltzmann Law and give the value of the Stefan-Boltzmann constant.
- What is the difference between a continuous blackbody spectrum and a discrete emission spectrum?
- How does a polarizer change unpolarized light, and what is the relationship for intensity reduction?
📘 Lecture 33 — INTERFERENCE AND DIFFRACTION
📖 Overview: This lecture explores how waves combine to produce interference patterns—both constructive and destructive—and how this principle applies to light. It explains the necessity of coherent sources for observing light interference, derives conditions for interference fringes in double-slit experiments, and extends these ideas to thin films and single-slit diffraction, concluding with limitations on optical resolution.
🗂️ Topics Covered
The lecture begins with the fundamental concepts of constructive and destructive interference for waves of the same frequency. It then discusses the need for coherent light sources, using a double-slit setup to produce an interference pattern. The condition for constructive interference is derived using path length difference. A worked example calculates wavelength from fringe positions. Reflection phase changes at interfaces are introduced, followed by the conditions for interference in thin films and the origin of colors. Finally, single-slit diffraction is explained, including its condition for bright fringes, a worked example, and its impact on the resolving power of telescopes and microscopes.
📝 Lecture Summary
1. Interference of Waves
Two waves of the same frequency add together. If they start together (in phase), the net amplitude increases—this is constructive interference. If they start at different times (out of phase), the net amplitude decreases—this is destructive interference. Interference occurs for any two waves, even with different amplitudes and frequencies.
2. Coherent Sources for Light Interference
To observe interference of light, a coherent source is necessary, meaning both waves must have a fixed phase relationship. Producing coherent light from two separate sources is very difficult. Observing interference usually requires taking two waves from a single source, each traveling a different path. In the classic double-slit experiment, an incoherent source illuminates a first slit, creating uniform coherent illumination of a second screen with two slits (S1 and S2). Waves from these slits then meet on a third screen, creating a pattern of alternating light and dark fringes. 💡 Why this matters: Coherence ensures a stable, observable interference pattern.
3. Condition for Interference
Bright fringes occur where constructive interference happens, and dark fringes where destructive interference occurs. For any point on the screen, light from S1 and S2 travels different distances, creating a phase difference. The extra distance traveled by light from one slit is ( d \sin \theta ). The extra time is ( (d \sin \theta) / c ).
-
Constructive interference occurs when this extra time equals ( T, 2T, 3T, \dots ). Since ( T = 1/\nu ) and ( c = \lambda \nu ), this leads to the condition: [ d \sin \theta = n \lambda \quad (n = 1, 2, 3, \dots) ]
-
Destructive interference occurs when the extra time equals ( \frac{T}{2}, \frac{3T}{2}, \frac{5T}{2}, \dots ). This leads to the condition: [ d \sin \theta = \left(n + \frac{1}{2}\right) \lambda ]
4. Worked Example: Double-Slit Wavelength
Two slits with a separation of (8.5 \times 10^{-5}) m create an interference pattern on a screen 2.3 m away. The tenth bright fringe (n=10) above the central fringe is at a linear distance of 12 cm from it. What is the wavelength of light used?
Solution: First, calculate the angle ( \theta ) to the tenth bright fringe using ( y = L \tan \theta ): [ \theta = \tan^{-1}\left(\frac{y}{L}\right) = \tan^{-1}\left(\frac{0.12 \text{ m}}{2.3 \text{ m}}\right) = 3.0^\circ ] Then, use the constructive interference condition ( d \sin \theta = n \lambda ) to solve for ( \lambda ): [ \lambda = \frac{d \sin \theta}{n} = \frac{(8.5 \times 10^{-5} \text{ m}) \sin(3.0^\circ)}{10} = 4.4 \times 10^{-7} \text{ m} = 440 \text{ nm} ]
5. Phase Change on Reflection and Thin Films
When a wave is reflected at the interface of two media, the phase does not change if it goes from a larger refractive index to a smaller one. However, for a wave going from a smaller refractive index to a larger one, there will be a phase change of a half-wavelength ((\pi) rad).
When light falls on a thin film (e.g., soapy water, oil), it is reflected from two surfaces. On the top surface (air to film), reflection occurs with a phase change of (\pi). At the lower surface (film to air), there is no phase change. When these two reflected waves combine, they interfere.
For a thin film of index (n) and thickness (d), viewed almost directly from above, the conditions are:
- Destructive interference: ( 2 n d = m \lambda \quad (m = 0, 1, 2, \dots) )
- Constructive interference: ( 2 n d = \left(m + \frac{1}{2}\right) \lambda \quad (m = 0, 1, 2, \dots) ) 💡 Why this matters: These conditions explain why thin films produce colors. Thick portions of a non-uniform film may appear blue (destructive interference for long-wavelength red), while thinner portions appear red (destructive interference for short-wavelength blue).
6. Diffraction
Diffraction is the bending of light around objects (into shadowed regions) and occurs when light passes through very small apertures or near sharp edges. Diffraction is essentially interference, with the source being different parts of the same wavefront. Interference from a single slit is called diffraction.
7. Condition for Diffraction from a Single Slit
For a single slit of width (W), a wave incident from the left causes secondary waves from the slit edges. At an angle (\theta), the extra distance traveled by a wave from one edge is (W \sin \theta). If this is a multiple of the wavelength, constructive interference occurs. The condition for bright fringes in a single-slit diffraction pattern is: [ W \sin \theta = m \lambda \quad (m = \pm 1, \pm 2, \pm 3, \dots) ] This results in a pattern of light and dark fringes observed on the other side.
8. Worked Example: Single-Slit Diffraction Angles
Light with a wavelength of 511 nm forms a diffraction pattern after passing through a single slit of width (2.2 \times 10^{-6}) m. Find the angle for the first and second bright fringe above the central bright fringe.
Solution: Using the condition ( W \sin \theta = m \lambda ), we solve for ( \theta = \sin^{-1}\left(\frac{m \lambda}{W}\right) ).
-
For (m = 1): [ \theta = \sin^{-1}\left(\frac{(1)(511 \times 10^{-9} \text{ m})}{2.20 \times 10^{-6} \text{ m}}\right) = 13.4^\circ ]
-
For (m = 2): [ \theta = \sin^{-1}\left(\frac{(2)(511 \times 10^{-9} \text{ m})}{2.20 \times 10^{-6} \text{ m}}\right) = 27.7^\circ ]
9. Diffraction and Resolution
Diffraction sets fundamental limits on the ability of telescopes and microscopes to distinguish (resolve) closely spaced objects. Light from a circular aperture creates a diffraction pattern. The first dark fringe occurs at an angle given by ( \theta = 1.22 \frac{\lambda}{D} ), where (D) is the aperture diameter. Two objects are barely resolved if the diffraction maximum of one lies exactly on the first diffraction minimum of the other. A larger aperture (D) results in a smaller angular separation for resolution, meaning better resolution.
⭐ Key Takeaways
The core principle of this lecture is that wave interference, both constructive and destructive, governs phenomena from double-slit patterns to the colors of thin films and the limits of optical instruments. A student must remember that constructive interference requires a path difference of an integer number of wavelengths ((n\lambda)), while destructive requires a half-integer multiple (((n+1/2)\lambda)). For thin films, the phase change upon reflection ((\pi) for reflection off a higher-index medium) is critical for determining these conditions. The same interference logic applies to single-slit diffraction, where the condition for bright fringes is (W \sin \theta = m\lambda). Finally, the concept of the resolution limit ((\theta \approx 1.22\lambda/D)) for circular apertures is a direct consequence of diffraction and is essential for understanding the capabilities of telescopes and microscopes.
🧠 Quick Revision Questions
- What is the condition for constructive interference in a double-slit experiment, and what physical quantity does the slit separation affect in the fringe pattern?
- A thin film of oil (n=1.25) floating on water appears orange under white light. If orange light has a wavelength of 600 nm in air, what is the minimum thickness of the oil film that would cause constructive interference for this color when viewed from above?
- A single slit produces a diffraction pattern on a screen. If the slit width is doubled, what happens to the angular positions of the bright fringes?
- Why is it necessary to use a coherent light source to observe stable interference fringes in light, unlike with water waves?
- A telescope with a 10 cm diameter lens can just resolve two stars as separate. If you want to build a telescope that can resolve stars that are twice as close together, what minimum diameter would the new lens need to have, assuming the same wavelength of light?