π Lecture 28 β Quality Control and Quality Assurance (Contd.)
π Overview: This lecture continues the study of quality control by focusing on the practical use and interpretation of control charts for both variables and attributes. It also introduces run tests for detecting non-random patterns in process output and explains the critical concept of process capability, including its measurement and improvement.
ποΈ Topics Covered
This lecture begins by describing SPC Type I and Type II errors, then moves to control charts for variables (mean and range charts) and attributes (p-charts and c-charts). It covers guidelines for using control charts, run tests for randomness, and identifying nonrandom patterns. The lecture concludes with a detailed discussion of process capability, the process capability ratio Cp, 3-sigma vs. 6-sigma quality, methods for improving process capability, and the Taguchi Loss Function.
π Lecture Summary
SPC Errors
Statistical Process Control involves two potential errors. A Type I error is concluding a process is not in control when it actually is, or concluding that no randomness is present when it is only randomness. The probability of this error is denoted by Ξ±. A Type II error is concluding a process is in control when it is not, or concluding that no randomness is present when it is.
π Definition β Type I error: Concluding a process is not in control when it actually is. π Definition β Type II error: Concluding a process is in control when it actually is not.
Control Charts for Variables
Control charts for variables monitor measurable characteristics. Mean control charts (X-bar charts) are used to monitor the central tendency of a process. Range control charts (R charts) are used to monitor process dispersion. The lecture shows that an X-bar chart can detect a shift in the process mean, while an R-chart may not detect this shift. Conversely, when process variability is increasing, the R-chart reveals the increase, while the X-chart does not.
CONTROL CHART FOR ATTRIBUTES
Attribute control charts monitor qualitative data. A p-Chart is used to monitor the proportion of defectives in a process. Use p-charts when observations can be placed into two categories (e.g., good/bad, pass/fail) and when data consists of multiple samples of several observations each. A c-Chart is used to monitor the number of defects per unit. Use c-charts only when the number of occurrences per unit of measure can be counted, but non-occurrences cannot be counted. Examples include scratches per item, cracks per unit of distance, or complaints per unit of time.
Use of Control Charts
Key decisions for using control charts include: at what point in the process to use them, what size samples to take, and what type of control chart to use (for variables or attributes).
Run Tests
A run test is a test for randomness. Any sort of pattern in the data would suggest a non-random process. Even if all points are within the control limits, the process may not be random. Nonrandom patterns in control charts include: Trend, Cycles, Bias, Mean shift, and Too much dispersion.
π Definition β Run test: A test used to check for randomness in process output data.
Counting runs is illustrated with two methods. Counting Above/Below Median Runs: A run is a sequence of identical observations (e.g., B, A, A, B, A, B, B, B, A, A β 7 runs). Counting Up/Down Runs: A run is a sequence of consecutive increases or decreases. The first value does not receive a U or D because nothing precedes it (e.g., U, U, D, U, D, U, D, U, U β 8 runs). Underlining each run helps in counting.
PROCESS CAPABILITY
Tolerances or specifications are the range of acceptable values established by engineering design or customer requirements. Process variability is the natural variability in a process. Process capability is the process variability relative to specification. Three cases are presented: Case A where process variability matches specifications; Case B where process variability is well within specifications; and Case C where the process is not capable. For Case C, a manager can: 1) Redesign the process; 2) Use an alternative process; 3) Retain the current process but use 100% inspection; or 4) Examine specifications to see if they can be relaxed.
π Definition β Process capability: The process variability relative to specification.
Process variability is the key factor and is measured in terms of process standard deviation. Process capability is considered to be Β± 3 standard deviations from the process mean. For example, an insurance company provides a service in 10 mins, with an acceptable variation of Β± 1 minute, and the process has a standard deviation of 0.5 min. It would not be capable because Β± 3 SDs would be Β± 1.5 mins, exceeding the specification of Β± 1 minute.
π‘ Why this matters: Process capability determines whether a process can consistently produce output that meets customer requirements.
Process Capability Ratio
The Process Capability Ratio (Cp) is calculated as:
π Formula: Cp = Specification width / Process width β Cp = (Upper specification β Lower specification) / 6Ο
This ratio compares the allowable spread of specifications to the actual spread of the process (6Ο, or Β±3Ο).
π Definition β Cp: A ratio that measures process capability by comparing specification width to process width.
3 SIGMA AND 6 SIGMA QUALITY
3-sigma quality allows for 1350 ppm (parts per million) defects on each side of the process mean. 6-sigma quality drastically reduces this to only 1.7 ppm defects on each side. The lecture includes a diagram showing these defect levels relative to the process mean for both Β±3 Sigma and Β±6 Sigma.
Improving Process Capability
Methods to improve process capability include: 1) Simplify; 2) Standardize; 3) Mistake-proof (Poka Yoke); 4) Upgrade equipment; and 5) Automate.
Taguchi Loss Function
The Taguchi Loss Function is introduced, though not elaborated in detail in this lecture text. It represents a quadratic loss function where any deviation from the target value results in a loss to society.
β Key Takeaways
The key takeaways from this lecture are the distinction between Type I and Type II errors in SPC, the differences between control charts for variables (X-bar and R charts) and attributes (p and c charts), and the importance of run tests for detecting non-random patterns even when all points are within control limits. You must understand process capability as process variability relative to specification, the formula for the Cp ratio, and how 6-sigma quality (1.7 ppm) is dramatically better than 3-sigma quality (1350 ppm). Finally, remember the five methods for improving process capability: simplify, standardize, mistake-proof, upgrade equipment, and automate.
π§ Quick Revision Questions
- What is the difference between a Type I error and a Type II error in SPC?
- Which control chart is used to monitor process dispersion, and which is used to monitor the central tendency?
- Under what conditions should a p-chart be used instead of a c-chart?
- What is a run test, and what nonrandom patterns can it detect?
- A process has a specification width of 12 mm and a standard deviation (Ο) of 2 mm. What is its Cp value, and is the process capable?
π Lecture 29 β AGGREGATE PLANNING
π Overview: This lecture introduces aggregate planning, an intermediate-range capacity planning process covering 2 to 12 months. It explains how operations managers balance supply and demand using various strategies, inputs, and outputs, and emphasizes the importance of cost and policy constraints in developing effective plans.
ποΈ Topics Covered
The lecture covers the definition and time horizon of aggregate planning, the three planning levels (short, intermediate, long range), the planning sequence, aggregate planning inputs (resources, demand forecast, policies, costs) and outputs (total cost, inventory, employment levels), proactive, reactive, and mixed strategies, demand and capacity options, and factors influencing strategy selection including costs and corporate policy.
π Lecture Summary
Learning Objectives
The lecture aims to teach the working and usefulness of aggregate planning, identify variable decision makers and possible strategies, describe graphical and quantitative planning techniques, and prepare aggregate plans while comparing their costs.
Planning Horizon
Aggregate planning is defined as intermediate-range capacity planning, usually covering 2 to 12 months. It sits between short-range plans (detailed plans like machine loading and job assignments, covering up to 2 months) and long-range plans (covering 1 year or more, focusing on long-term capacity and location/layout).
As an Operations Manager, you must understand three planning levels:
- Short-range plans (Detailed plans): Machine loading and job assignments
- Intermediate plans (General levels): Employment, finished goods inventories, subcontracting, backorders, and output
- Long-range plans: Long-term capacity and location/layout
Planning Sequence
The planning sequence is presented as a flow diagram showing how long-range plans feed into intermediate-range plans (aggregate planning), which then feed into short-range plans. This hierarchical structure ensures alignment across all planning levels.
Aggregate Planning Inputs
The inputs required for aggregate planning include:
- Resources: Workforce and facilities
- Demand forecast: Expected customer demand
- Policies: Subcontracting, overtime, inventory levels, back orders
- Costs: Inventory carrying costs, back orders, hiring/firing costs, overtime, inventory changes, and subcontracting
π‘ Why this matters: All these inputs must be carefully estimated because they directly determine the feasibility and cost of any aggregate plan.
Aggregate Planning Outputs
The outputs generated from aggregate planning are:
- Total cost of a plan
- Projected levels of inventory
- Inventory
- Output
- Employment
- Subcontracting
- Backordering
These outputs allow managers to compare different plans and select the most cost-effective approach.
Aggregate Planning Strategies
Three main strategy categories exist:
- Proactive Strategy: Strategies that alter demand to match capacity.
- Reactive Strategy: Strategies that alter capacity to match demand.
- Mixed Strategy: Strategies that make use of qualities from both proactive and reactive strategies.
Demand and Capacity Options
Demand Options primarily focus on market aspects, except for backorders which is operational management in nature. The four common demand options are:
- Pricing
- Promotion
- Back orders
- New demand
Operations managers should know all four but should be more interested in the back order option.
Capacity Options primarily focus on:
- Hire and layoff workers
- Overtime/slack time
- Part-time workers
- Inventories
- Subcontracting
- Maintain a level workforce
- Maintain a steady output rate
- Match demand period by period
- Use a combination of decision variables
π Definition β Demand options vs. Capacity options: Demand options are short range in nature, while capacity options are long duration (term or range).
Which Strategy to Use
The organization needs to consider two factors before choosing a strategy:
- Costs β The financial implications of each option
- Company/Corporate Policy β Policy can set constraints on available options. For example, layoffs and subcontracting/outsourcing may be restricted (as with PIA subcontracting its databases to protect secrecy).
π‘ Why this matters: As a rule of thumb, aggregate planners seek to match supply and demand within constraints set by policies and at minimum costs.
β Key Takeaways
You MUST remember that aggregate planning is an intermediate-range (2β12 month) process that bridges long-term capacity decisions with short-term operational details. The key inputs are resources, demand forecasts, policies, and costs, while outputs include total plan cost, inventory levels, and employment projections. Three strategy types exist: proactive (alter demand), reactive (alter capacity), and mixed (combine both). Demand options are short-range and market-focused, while capacity options are long-range and operationally focused. Most importantly, strategy selection is driven by cost considerations and corporate policy constraints, with the ultimate goal being to match supply and demand at minimum cost within policy boundaries.
π§ Quick Revision Questions
- What is the typical time horizon for aggregate planning, and how does it differ from short-range and long-range plans?
- List at least five inputs required for aggregate planning and explain why each is important.
- What is the difference between a proactive strategy and a reactive strategy in aggregate planning? Provide one example of each.
- Why are demand options considered short-range while capacity options are considered long-range?
- What two major factors should an organization consider before choosing an aggregate planning strategy, and how might corporate policy constrain available options?
π Lecture 30 β Aggregate Planning (Contd.)
π Overview: This lecture continues the discussion of aggregate planning, covering basic strategies, assumptions, relationships, and mathematical techniques. It introduces the master schedule and master scheduler, explaining how aggregate plans are disaggregated for production control. This provides the foundation for deeper study of inventory management and MRP/ERP, enabling effective operations management.
ποΈ Topics Covered
The lecture covers basic aggregate planning strategies (level capacity and chase demand) with their advantages and disadvantages, techniques for aggregate planning, assumptions for aggregate planning, aggregate planning relationships including workforce and inventory calculations, cost calculations, mathematical techniques like linear programming and linear decision rule, aggregate planning in services, disaggregating the aggregate plan into the master schedule, the role of the master scheduler, projected on-hand inventory, and stabilizing the master schedule using time fences.
π Lecture Summary
Basic Strategies
Two fundamental aggregate planning strategies are introduced. The level capacity strategy maintains a steady rate of regular-time output while meeting variations in demand through a combination of options like inventory, overtime, or subcontracting. The chase demand strategy matches capacity to demand by setting planned output for a period equal to the expected demand for that period.
The Chase Approach has advantages: investment in inventory is low and labor utilization is high. Its disadvantages include the cost of adjusting output rates and/or workforce levels. The Level Approach has the advantage of stable output rates and workforce, but disadvantages include greater inventory costs, increased overtime and idle time, and resource utilizations that vary over time.
Techniques for Aggregate Planning
The systematic process for aggregate planning involves six steps:
- Determine demand for each period
- Determine capacities for each period
- Identify policies that are pertinent
- Determine unit costs
- Develop alternative plans and costs
- Select the best plan that satisfies objectives. Otherwise return to step 5.
Assumptions for Aggregate Planning
Several assumptions underlie aggregate planning. The regular output capacity is the same for all periods. Cost (back order, inventory, subcontracting, etc.) is a linear function composed of unit cost and number of units (in reality, cost is more of a step function). Plans are feasible, meaning sufficient inventory exists to accommodate a plan, subcontractors provide quality products, and outsourcers are secure. All costs associated with a decision option can be represented by a lump sum or by unit costs independent of quantity. Cost figures can be reasonably estimated and are constant over the planning horizon. Inventories are built up and drawn down at a uniform rate, and output occurs at a uniform rate throughout each period. Backlogs are treated as if they exist for the entire period, even though in reality they tend to build up towards the end of the period.
Aggregate Planning Relationships
Key relationships govern workforce and inventory calculations. The number of workers in a period equals the number of workers at the end of the previous period PLUS number of new workers at the start of the current period MINUS number of laid-off workers at the start of the current period.
π Definition β Note: Since the organization would not hire and layoff simultaneously, at least one of the last two terms will be "0".
Inventory at the end of a current period equals inventory at the end of the previous period PLUS production in the current period MINUS amount used to satisfy the demand in the current period.
π Definition β Average Inventory: The average inventory for a period is equal to (Beginning Inventory Plus Ending Inventory)/2
Cost for a current period equals Output Cost (Regular + OT + Subcontract) + Hire/Layoff Cost + Inventory Cost + Backorder Cost. The cost of a particular plan for a given period can be determined by summing the appropriate costs.
Aggregate Planning Relationships β Cost Types
| Type of Costs | How to Calculate |
|---|---|
| Output β Regular | Regular Cost per Unit X Quantity of Regular Output |
| Output β Overtime | Overtime Cost per Unit X Overtime Quantity |
| Output β Subcontract | Subcontract Cost per Unit X Subcontract Quantity |
| Hire/Layoff β Hire | Cost Per Hire X Number Hired |
| Hire/Layoff β Layoff | Cost per Layoff X Number laid off |
| Inventory | Carrying Cost per Unit X Average Inventory |
| Back Order | Back Order Cost Per Unit X Number of Backorder Units |
Mathematical Techniques
Linear programming is a method for obtaining optimal solutions to problems involving allocation of scarce resources in terms of cost minimization. The linear decision rule is an optimizing technique that seeks to minimize combined costs, using a set of cost-approximating functions to obtain a single quadratic equation.
| Technique | Solution | Characteristics |
|---|---|---|
| Graphical/charting | Trial and error | Intuitively appealing, easy to understand; solution not necessarily optimal |
| Linear programming | Optimizing | Computerized; linear assumptions not always valid |
| Linear decision rule | Optimizing | Complex, requires considerable effort to obtain pertinent cost information and to construct model; cost assumptions not always valid |
| Simulation | Trial and error | Computerized models can be examined under a variety of conditions |
Aggregate Planning in Services
Services have unique characteristics that affect aggregate planning. Services occur when they are rendered, and unlike most manufacturing output, most services cannot be inventoried. Services such as financial planning, tax counseling, and oil changes cannot be inventoried/stockpiled, removing the option of building up inventories during a slow period in anticipation of future demand.
Demand for service can be difficult to predict, and the volume of demand for services is often variable. In some situations, customers may need prompt service (e.g., police, fire, medical emergency), while in others they may not need prompt service and may be willing to find some other service provider.
Capacity availability can be difficult to predict. Processing requirements for services can sometimes be quite variable, similar to the variability of work in a job shop setting. It is difficult to measure the capacity of a person rendering a service (a dentist, a Montessorian, a bank teller) in anticipation of future demand.
Labor flexibility can be an advantage in services. Labor often comprises a significant portion of service compared to manufacturing. Coupled with the fact that service providers are often able to handle a fairly wide variety of service requirements, to some extent, planning is easier than manufacturing.
Disaggregating the Aggregate Plan
The aggregate plan is broken down into master schedules and rough-cut capacity planning charts. The master schedule is the result of disaggregating an aggregate plan; it shows quantity and timing of specific end items for a scheduled horizon. Rough-cut capacity planning involves approximate balancing of capacity and demand to test the feasibility of a master schedule.
For example, suppose the organization is making 500 aggregate units of air conditioners for the month of March and April with the breakup being 200 for window types and 300 for split types with further tonnage capacities. A master schedule shows the planned output for individual products rather than an entire product group, along with the timing of production.
With rough-cut capacity planning, we can check capacities of production and warehouse constraints exist, ensuring that no gross deficiencies exist that will render the master schedule unworkable. The master schedule then serves as the basis for short-range planning. The master schedule is disaggregated in stages or phases, which may cover weeks or months. It determines quantities needed to meet demand and interfaces with marketing, capacity planning, production planning, and distribution planning.
Master Scheduling
A master schedule indicates the quantity and timing (i.e., delivery times) for a product or a group of products, but it does not show planned production. For example, a master schedule may call for delivery of 500 air conditioners on April 1, but it may not require any production because of availability of 1000 air conditioners in inventory. Or if there are only 400 air conditioners, 100 would be planned for production.
Master Scheduler
The master scheduler evaluates the impact of new orders, provides delivery dates for orders, and deals with problems including production delays, revising the master schedule, and insufficient capacity.
Projected On-hand Inventory
The projected on-hand inventory equals inventory from the previous week MINUS the current week's requirements.
π Formula: Projected on-hand inventory = Inventory from previous week β Current weekβs requirements
Stabilizing the Master Schedule β Time Fences
Changes to a master schedule can be disruptive, particularly changes to the early, or near, portions of the schedule. Typically, the further out in the future a change is, the less the tendency to cause problems.
Master Production Schedules are often divided into 4 stages or phases. The dividing lines between phases are sometimes referred to as time fences. In the first phase (usually the first few periods of the schedule), changes can be quite disruptive. Consequently, once established, that portion of the schedule is generally frozen, implying that all but the most critical changes cannot be made without permission from the highest levels in an organization. This helps in achieving a high degree of stability in the production system.
In the next stage (perhaps the next two or three periods), changes are still disruptive but not to the extent they are in the first phase. Management views the schedule as firm, and only exceptional changes are made, which helps an organization gain some competitive advantage. In the third stage, management views the schedule as full, meaning that all available capacity has been allocated. Although changes do impact the schedule, their effect is less dramatic, and they are usually made if there is good reason for doing so. In the final phase, management views the schedule as open, meaning that not all capacity has been allocated. This is where new orders are usually added to the schedule.
β Key Takeaways
The two fundamental aggregate planning strategies are level capacity (steady output with inventory/buffers) and chase demand (matching output to demand each period), each with trade-offs in inventory, labor utilization, and costs. Linear programming and the linear decision rule are mathematical optimization techniques, while graphical and simulation methods provide trial-and-error solutions. Aggregate planning in services is constrained by the inability to inventory most services, variable demand, and variable capacity, though labor flexibility provides an advantage. The aggregate plan is disaggregated into a master schedule showing specific end-item quantities and timing, with rough-cut capacity planning verifying feasibility. The master schedule is stabilized through time fences: frozen (Phase 1), firm (Phase 2), full (Phase 3), and open (Phase 4), where only the open phase readily accepts new orders.
π§ Quick Revision Questions
- What are the two basic aggregate planning strategies, and what are their primary advantages and disadvantages?
- List the six steps in the technique for aggregate planning.
- How is the number of workers in a period calculated using aggregate planning relationships?
- Why is it difficult to apply aggregate planning to services compared to manufacturing, and what advantage do services have?
- What are the four phases of a master schedule as defined by time fences, and what does each phase imply about change flexibility?
π Lecture 31 β Inventory Management
π Overview: This lecture introduces the fundamental concepts of inventory management, including the types of inventories held by organizations and the objectives that guide inventory control. It explains why firms hold inventory, the requirements for an effective inventory management system, and the different systems used to count and track inventory items, including periodic and perpetual systems.
ποΈ Topics Covered
This lecture covers the five common types of inventories, the objectives of inventory control (customer service and cost management), and the eight key functions of inventory in a manufacturing organization. It also outlines the requirements for an effective inventory management system, including tracking systems, demand forecasting, lead time knowledge, and cost estimates. Finally, it details the two main inventory counting systems: the periodic system and the perpetual inventory system, with examples like the Two-Bin System and Universal Bar Codes.
π Lecture Summary
Types of Inventories
The five common types of inventories are: raw materials and purchased parts; partially completed goods called work in progress; finished-goods inventories (for manufacturing firms) or merchandise (for retail stores); goods-in-transit to warehouses or customers; and replacement parts, tools, & supplies. Understanding these categories is the first step in managing the flow of materials through an organization.
Objective of Inventory Control
The primary objective of inventory control is to achieve satisfactory levels of customer service while keeping inventory costs within reasonable bounds. Operations Managers must consider both internal customers (other departments) and external customers (end users). The two key elements to balance are: (1) the level of customer service and (2) the costs of ordering and carrying inventory.
Functions of Inventory
A manufacturing organization holds inventory to fulfill one or more of the following functions:
- To meet anticipated demand.
- To smooth production requirements.
- To decouple operations.
- To protect against stock-outs.
- To take advantage of quantity discounts.
- To permit operations.
- To help hedge against price increases.
- To take advantage of order cycles.
Requirements of Effective Inventory Control
Management has two basic functions concerning inventory: (1) making decisions about how much and when to order, and (2) establishing a system for keeping track of items. An effective inventory management system must fulfill five requirements:
- A system to keep track of inventory.
- A reliable forecast of demand.
- Knowledge of lead times.
- Reasonable estimates of: (a) holding costs, (b) ordering costs, and (c) shortage costs.
- A classification system. π‘ Why this matters: Without these elements, inventory decisions are based on guesswork, leading to stockouts or excessive carrying costs.
Inventory Counting Systems
There are two famous types of inventory counting systems.
π Definition β Periodic System: A physical count of items made at periodic intervals (e.g., monthly or yearly).
π Definition β Perpetual Inventory System (Continual): A system that keeps track of removals from inventory continuously, thus monitoring current levels of each item in real-time. The two common perpetual inventory systems found in Pakistan are:
- Two-Bin System: Two containers of inventory are used; reorder when the first bin is empty.
- Universal Bar Code: A bar code printed on a label that has information about the item to which it is attached. Scanning the bar code automatically updates the inventory record.
β Key Takeaways
Inventory management aims to balance customer service levels with inventory costs. Firms hold inventory for eight main reasons, including meeting demand, smoothing production, and protecting against stockouts. An effective system requires accurate tracking, reliable demand forecasts, knowledge of lead times, and cost estimates. The two primary counting systems are periodic (physical counts at fixed intervals) and perpetual (continuous tracking), with perpetual systems including the Two-Bin System and Universal Bar Codes. The five common types of inventories are raw materials, work in progress, finished goods, goods in transit, and supplies.
π§ Quick Revision Questions
- What are the five common types of inventories listed in this lecture?
- What are the two key elements that the objective of inventory control must balance?
- List any four of the eight functions of inventory in a manufacturing organization.
- What are the five requirements for an effective inventory management system?
- How does a Perpetual Inventory System differ from a Periodic System, and name the two common perpetual systems mentioned?
π Lecture 32 β Inventory Management (Contd.)
π Overview: This lecture continues the study of Inventory Management, focusing on the ABC Classification System, key inventory cost terms, and the foundational Economic Order Quantity (EOQ) model. It explains how different inventory items are categorized based on value and how to mathematically determine the optimal order quantity that minimizes total inventory costs, which is critical for efficient operations management.
ποΈ Topics Covered
This lecture begins by defining key inventory terms such as Lead time, Holding costs, Ordering costs, and Shortage costs. It then explains the ABC Classification System for categorizing inventory items by monetary value and control level, followed by a discussion of Cycle Counting. The main focus is on the Economic Order Quantity (EOQ) model, its assumptions, the inventory cycle graph, total cost formulas, and the derivation of the EOQ formula. A detailed numerical example demonstrates the calculation of EOQ, reorder frequency, order cycle length, and total annual cost.
π Lecture Summary
Key Inventory Terms
The foundational terms for inventory management are Lead time, Holding (carrying) costs, Ordering (Setup) costs, and Shortage (Stock out) costs. Lead time is the time interval between ordering and receiving the order. Holding (carrying) costs are the costs to carry an item in inventory for a length of time, usually a year, and include interest, insurance, taxes, depreciation, obsolescence, deterioration, pilferage, breakage, warehousing costs, and opportunity costs. These costs can be stated as a percentage of unit price or in rupees. Ordering costs are the costs of ordering and receiving inventory, which vary with the actual placement of the order. Shortage costs are the costs incurred when demand exceeds supply.
ABC Classification System
An important aspect of Inventory Management is that items held in inventory are not of equal importance in terms of rupees invested or profit potential. The ABC Classification System controls inventories by dividing items into 3 groups: A, B, and C. Group A consists of High Rupee (Monetary) Value items that account for a small portion, about 10% of total inventory usage. Group B consists of Medium Rupee (Monetary) Value items, accounting for about 20% of total inventory usage. Group C consists of Low Rupee (Monetary) Value items, accounting for a large portion, about 70% of total inventory usage. The level of control reflects cost-benefit concerns: Group A items are reviewed on a regular basis, Group B items are reviewed less frequently than Group A but more than Group C, while Group C items are not reviewed and orders are placed directly.
π Definition β ABC Classification System: A method for controlling inventory by dividing items into three groups (A, B, C) based on their monetary value and importance, with varying levels of control for each group.
π Example: The lecture provides a table to classify inventory items. An item's classification is based on its Annual Value (Demand Γ Unit Cost). For instance, if Rupee values up to Rs. 50,000 represent Class C and up to Rs. 500,000 represent Class B, then an item like "PC" with an Annual Value of Rs. 200,000 would be classified as B. An item like "RAM" with an Annual Value of Rs. 2,000,000 would be classified as A.
Cycle Counting
Cycle Counting is a physical count of items in inventory, rather than a full year-end inventory. Its management involves three key questions: How much accuracy is needed? When should cycle counting be performed? Who should do it?
Economic Order Quantity Models
The lecture introduces three types of Economic Order Quantity Models: the Economic Order Quantity (EOQ) model, the Economic Production model, and the Quantity Discount model. The focus is on the basic EOQ model.
Assumptions of EOQ Model
The basic EOQ model relies on several key assumptions: only one product is involved; annual demand requirements are known; demand is even throughout the year; lead time does not vary; each order is received in a single delivery; and there are no quantity discounts.
The Inventory Cycle
The Inventory Cycle is a graphic representation of inventory levels over time. It shows a sawtooth pattern starting with a maximum quantity (Q) that is used up at a constant Usage rate until it reaches the Reorder Point. At this point, an order is placed, and after the Lead time, the order is received, at which point the inventory level jumps back to Q.
π Formula: Total Cost (TC) $$TC = \frac{Q}{2} H + \frac{D}{Q} S$$ Where:
- ( Q ) = Order Quantity
- ( H ) = Annual Holding Cost per unit
- ( D ) = Annual Demand
- ( S ) = Ordering Cost per order
- ( \frac{Q}{2} H ) = Annual Carrying (Holding) Cost
- ( \frac{D}{Q} S ) = Annual Ordering Cost
- π‘ This formula shows that the total cost is the sum of annual holding and ordering costs.
Cost Minimization Goal
The goal is to find the order quantity (Q) that minimizes the Total Cost (TC). The total cost curve is derived by adding the Holding Costs curve (which increases as Q increases) and the Ordering Costs curve (which decreases as Q increases). The point where these two curves intersect is the Optimal Order Quantity (QopT).
Deriving the EOQ
Using calculus, the derivative of the total cost function is taken and set equal to zero to solve for Q, which yields the Economic Order Quantity (EOQ) formula.
π Formula: Economic Order Quantity (EOQ or QopT) $$Q_{OPT} = \sqrt{\frac{2DS}{H}}$$ Where:
- ( D ) = Annual Demand
- ( S ) = Order or Setup Cost per order
- ( H ) = Annual Holding Cost per unit
π Minimum Total Cost: The total cost curve reaches its minimum where the carrying costs and ordering costs are equal.
π Example 2: A distributor expects to sell 10,000 aerobic exercise machines annually. The annual carrying cost (H) is Rs. 2,500 per machine, and the order cost (S) is Rs. 10,000. The distributor operates 300 days a year.
-
Calculate EOQ (Qβ): $$Q_0 = \sqrt{\frac{2DS}{H}} = \sqrt{\frac{2 \times 10,000 \times 10,000}{2,500}} = \sqrt{80,000} = 283 \text{ machines per year}$$
-
Number of times the store will reorder (D/Qβ): $$\frac{D}{Q_0} = \frac{10,000}{283} = 35.34 \approx 35 \text{ times}$$
-
Length of an Order Cycle (Qβ/D): $$\frac{Q_0}{D} = \frac{283}{10,000} = 0.0283 \text{ years} = 0.0283 \times 300 \text{ days} = 8.49 \text{ days}$$
-
Total Annual Cost (TC) if EOQ is ordered: $$TC = \text{Carrying Cost} + \text{Ordering Cost} = \frac{Q_0}{2} (H) + \frac{D}{Q_0} (S)$$ $$TC = \frac{283}{2} (2500) + \frac{10,000}{283} (10,000)$$ $$TC = 353,750 + 353,353 = \text{Rs. 707,107}$$
β Key Takeaways
A student must remember that inventory items are not all equal in value, which is why the ABC Classification System helps prioritize management attention on high-value (A) items and simplifies control for low-value (C) items. The core of quantitative inventory management is the EOQ model, which mathematically finds the order quantity that minimizes the sum of annual holding and ordering costs, assuming known, constant demand and stable lead times. The key formula ( Q = \sqrt{\frac{2DS}{H}} ) is derived from the concept that optimal total cost occurs where holding cost equals ordering cost. Finally, knowing how to apply the EOQ formula to calculate total cost, order frequency, and cycle length from given demand, cost, and operating days is essential for practical application.
π§ Quick Revision Questions
- What are the four key inventory cost terms defined in this lecture, and what does each one represent?
- Explain the ABC Classification System. What percentage of inventory usage and what level of control is associated with Group B items?
- List the six assumptions required for the basic Economic Order Quantity (EOQ) model to be valid.
- In the EOQ model, what is the relationship between annual carrying costs and annual ordering costs at the optimal order quantity (Qopt)?
- Using the EOQ formula, if annual demand (D) is doubled but holding cost (H) and ordering cost (S) remain the same, what happens to the optimal order quantity?
π Lecture 33 β INVENTORY MANAGEMENT (Contd.)
π Overview: This lecture completes the discussion on Inventory Management by covering types of inventories, objectives of inventory control, and the major reasons for holding inventories. It differentiates between independent and dependent demand, reviews periodic and perpetual inventory systems, and introduces advanced concepts like Economic Production Quantity (EPQ), Quantity Discounts, Reorder Point, Safety Stock, and the Fixed-Order-Interval Model, all with solved numerical examples.
ποΈ Topics Covered
This lecture covers the continuation of Inventory Management, including a solved example on Economic Order Quantity (EOQ) with percentage-based carrying costs, the Economic Production Quantity (EPQ) model with its assumptions and finer points, the concept of Quantity Discounts and its total cost calculation, the Reorder Point (ROP) with safety stock and service level calculations using normal distribution tables, and finally the Fixed-Order-Interval Model.
π Lecture Summary
Example (In terms of Percentage)
A CNG-LPG company in Karachi purchases 5000 compressors a year at Rs. 8,000 each. Ordering costs are Rs. 500 and annual carrying costs are 20% of the purchase price. The optimal order quantity and total annual cost are computed.
π Definition β D (Annual Demand): The total quantity demanded per year. π Formula (for Carrying Cost per unit, H): H = Purchase Price Γ Carrying Cost Percentage β‘οΈ H = 0.2 Γ 8,000 = Rs. 1,600 per compressor per year. π Formula (EOQ with percentage cost): Qβ = β(2DS / H) β‘οΈ Qβ = β(2(5,000)(500) / 1600) = β(5,000,000 / 1600) = β3125 = 55.9 β 56 Compressors. π Formula (Total Cost, TC): TC = (Qβ/2)H + (D/Qβ)S β‘οΈ TC = (56/2)(1600) + (5000/56)(500) = 28(1600) + 44,643 = 44,800 + 44,643 = Rs. 89,443.
Economic Production Quantity (EPQ)
This model is used when a firm produces its own inventory. Unlike EOQ (where the entire order arrives at once), inventory is replenished incrementally over time because production and usage occur simultaneously.
π Definition β Economic Production Quantity (EPQ): An inventory model that determines the optimal production lot size when the producer is also the user, and inventory is built up gradually over the production run time. π Definition β Setup Cost: The cost to prepare a machine or process for a production run; analogous to ordering cost in EOQ.
EPQ Assumptions:
- Production is done in batches or lots.
- Capacity to produce a part exceeds the partβs usage or demand rate.
- Only one item is involved.
- Annual demand is known and usage rate is constant.
- Usage occurs continuously and the production rate is constant.
- Lead time does not vary.
- No quantity discounts.
Finer Points of EPQ Model:
- If usage and production rates are equal, there is no buildup of inventory.
- The larger the run size, the fewer the number of runs needed, and hence lower annual setup cost.
- The number of runs is D/Q and annual setup cost is (D/Q)S.
- Total Cost (TCmin) = Carrying Cost + Setup Cost = (Imax/2)H + (D/Qβ)S, where Imax = Maximum Inventory.
π Formula (Economic Run Size, Qβ): Qβ = β(2DS / H) Γ β(p / (p - u))
- Where p = production rate and u = usage rate. π Formula (Run Time) = Qβ / p π Formula (Maximum Inventory, Imax) = Qβ/p Γ (p - u) π Formula (Average Inventory) = Imax / 2
π Example (Economic Run Size): A firm in Sialkot produces 250,000 footballs per year. It can make footballs at a rate of 2000 per day. The manufacturing unit operates for 250 days per year. Carrying cost is Rs. 100 per football and setup cost is Rs. 2500.
- Optimal Run Size: Qβ = β(2 Γ 250,000 Γ 2500 / 100) Γ β(2000 / (2000 - 1000)) = β(12,500,000) Γ β(2) = 2500 Γ 1.414 = 5000 footballs.
- Minimum Total Annual Cost: Imax = (5000/2000) Γ (2000 - 1000) = 2.5 Γ 1000 = 2500 footballs. TC = (2500/2)(100) + (250,000/5000)(2500) = 1250(100) + 125,000 = 125,000 + 125,000 = Rs. 250,000.
- Cycle Time: Qβ / u = 5000 / 1000 = 5 days.
- Run Time: Qβ / p = 5000 / 2000 = 2.5 days.
Quantity Discounts
π Definition β Quantity Discount: Price reductions for large orders. This model adds the purchasing cost (PD) to the total cost equation.
π Formula (Total Cost with Purchasing Cost): TC = (Q/2)H + (D/Qβ)S + PD π‘ Why this matters: Adding purchasing cost does not change the optimal EOQ for a given price break, but calculations must be performed for each price level to find the true minimum total cost.
π Example (Optimal Order Quantity and Total Cost): A hospital uses 1200 cases of liquid/year. Ordering cost is Rs. 100, carrying cost is Rs. 20 per case. Price schedule: 1-49 cases @ Rs. 1250, 50-79 @ Rs. 1150, 80-99 @ Rs. 1050, 100+ @ Rs. 1000. Step 1: Compute common EOQ = β(2 Γ 100 Γ 1200 / 20) = β12000 = 109.5 β 110 cases. Since 110 falls in the "100 or more" range, this is feasible at Rs. 1000/case. Step 2: Compute TC = (110/2)(20) + (1200/110)(100) + (1200 Γ 1000) = 1100 + 1091 + 1,200,000 = Rs. 1,202,191.
When to Reorder with EOQ Ordering
π Definition β Reorder Point (ROP): The quantity on hand that triggers a new order; it is when inventory drops to this amount, the item is reordered. π Definition β Safety Stock: Stock held in excess of expected demand to protect against variable demand rate and/or lead time. π Definition β Service Level: The probability that demand will not exceed supply during lead time.
Determinants of the Reorder Point:
- The rate of demand
- The lead time
- Stock out risk (safety stock)
- Demand and/or lead time variability
π Formula (Basic ROP) = Usage Γ Lead Time π Example: An apartment complex uses 2 barrels of water/day. Lead time is 5 days. ROP = 2 Γ 5 = 10 barrels.
π Example (ROP with Safety Stock): A Montessori equipment firm has an average lead time demand of 25 tons, standard deviation of 2.5 tons, and a stock out risk β€ 6%. a. Z-value: For risk = 6% (service level = 94%), from the normal table, Z = 1.55. b. Safety Stock: SS = Z Γ Ο_dLT = 1.55 Γ 2.5 = 3.875 tonnes. c. Reorder Point: ROP = Expected Lead Time Demand + Safety Stock = 25 + 3.875 = 28.875 tonnes. d. Expected Shortage per Cycle (for 80% service level): From table, E(z) = 0.7881. E(n) = E(z) Γ Ο_dLT = 0.7881 Γ 2.5 = 1.97025 tonnes. e. Annual Service Level: SL_annual = 1 β [E(z) Γ Ο_dLT / Q] = 1 β [0.7881(2.5)/25] = 1 β 0.07881 = 0.921 (92.1%).
Fixed-Order-Interval Model
π Definition β Fixed-Order-Interval Model: An inventory system where orders are placed at fixed time intervals, and the order quantity varies based on the amount of inventory on hand. Key Characteristics:
- Orders are placed at fixed time intervals.
- The order quantity for the next interval is determined at each order point.
- Suppliers might encourage fixed intervals.
- May require only periodic checks of inventory levels.
- There is a risk of stock out if demand is higher than expected during the interval.
β Key Takeaways
- The Economic Production Quantity (EPQ) model is essential when a firm produces its own inventory, accounting for simultaneous production and usage, and uses the formula Qβ = β(2DS/H) Γ β(p/(p-u)).
- Quantity Discount models require calculating the EOQ for the lowest price bracket and checking feasibility, then computing total cost including purchasing cost (PD) to find the true optimal order quantity.
- The Reorder Point (ROP) is a critical trigger for placing new orders and is calculated as ROP = (Demand Γ Lead Time) + Safety Stock, where safety stock is determined by desired service level and demand variability using normal distribution Z-values.
- Service Level and Stockout Risk are inversely related; a higher service level (e.g., 94%) requires a higher Z-value and thus more safety stock, increasing carrying costs.
- The Fixed-Order-Interval Model orders at constant time intervals with variable quantities, which is simpler for periodic review but carries a higher risk of stockout compared to the continuous-review EOQ model.
π§ Quick Revision Questions
- What are the key assumptions of the Economic Production Quantity (EPQ) model, and how does it differ from the basic EOQ model?
- A company produces 50,000 units per year at a rate of 500 units per day and uses 200 units per day. If setup cost is Rs. 1000 and holding cost is Rs. 50 per unit, what is the optimal production run size?
- In the Quantity Discount model, why is the total cost computed for each feasible price break, and what is the formula for TC including purchasing cost?
- Using the ROP formula, if average lead time demand is 100 units with a standard deviation of 15 units, what is the reorder point for a 95% service level (Z=1.65)?
- What is the primary difference in ordering logic between the Fixed-Order-Interval Model and the Continuous Review (EOQ) model, and what is the main risk of the fixed-interval approach?