π Lecture 15 β Analog Mobile Phone System
π Overview: This lecture introduces the Analog Mobile Phone System (AMPS), the first-generation cellular standard deployed in the US in 1983. It covers the system architecture, call handling procedures, air interface specifications, supervisory signaling, and the narrowband evolution N-AMPS, providing foundational knowledge for understanding how early cellular networks operated.
ποΈ Topics Covered
The lecture covers AMPS introduction with its history and frequency allocation, system architecture including forward and reverse channels, call handling procedures for both landline-to-mobile and mobile-to-landline calls, AMPS and ETACS air interface parameters, supervisory signals (SAT and ST tones), wideband blank-and-burst encoding, and the Narrowband AMPS (N-AMPS) system.
π Lecture Summary
AMPS Introduction
AMPS (Advanced Mobile Phone System) was first deployed in late 1983 in Chicago, covering approximately 2100 square miles. The FCC allocated a total of 40 MHz in the 800 MHz band, with an additional 10 MHz added later due to increased demand. Early systems used large cells and omni-directional antennas to minimize initial equipment costs.
AMPS uses a 7-cell reuse pattern with provision for sectoring and cell splitting to increase capacity. Through extensive testing, it was determined that a 30 KHz channel requires a Signal-to-Interference Ratio (SIR) of 18 dB. The smallest reuse factor satisfying this requirement with 120-degree directional antennas is N = 7.
π Definition β ETACS (European Total Access Communication System): Identical to AMPS but scaled to 25 KHz channels instead of 30 KHz, with a different mobile identification number (MIN) format to accommodate different country codes in Europe versus area codes in the US.
System Overview
AMPS and ETACS both use FM (Frequency Modulation) and FDD (Frequency Division Duplex) for radio transmission. In the US, transmissions from mobiles to base stations (reverse link) use frequencies between 824-849 MHz, while base stations transmit to mobiles (forward link) using frequencies between 869-894 MHz. A separation of 45 MHz between forward and reverse channels allows for inexpensive duplexers in mobile units.
The control channel and blank-and-burst data streams are transmitted at 10 kbps in AMPS and 8 kbps in ETACS, with maximum frequency deviations of Β±8 KHz and Β±6.4 KHz respectively. Each base station has:
- One control channel transmitter for the Forward Control Channel (FCC)
- One control channel receiver for the Reverse Control Channel (RCC)
- 8 or more duplex voice channels (commercial BS supports up to 57 voice channels)
The Forward Voice Channel (FVC) carries conversation from landline caller to cellular subscriber, while the Reverse Voice Channel (RVC) carries it in the opposite direction. Each BS continuously transmits digital FSK data on FCC so idle subscriber units can lock onto the strongest signal. All users must be locked onto an FCC to originate or receive calls.
In US AMPS, there are 21 control channels per provider, while ETACS supports 42 control channels. The nonwireline service provider ("A" provider) is assigned odd System Identification Numbers (SID), and wireline provider ("B" provider) gets even SID. SID is transmitted every 0.8 seconds on each FCC. ETACS uses Area Identification Numbers (AID) instead.
Call Handling
Landline to Cellular Subscriber Call:
- Call arrives from PSTN at the MSC (Mobile Switching Center)
- A paging request with the subscriber's MIN (Mobile Identification Number) is sent simultaneously on every BS's FCC
- The subscriber responds with an acknowledgment on RCC
- MSC directs the BS to assign an FVC and RVC pair
- BS assigns a Supervisory Audio Tone (SAT) and a Voice Mobile Attenuation Code (VMAC)
π Definition β SAT (Supervisory Audio Tone): Allows user and BS to distinguish each other from co-channel users in different cells; transmitted continuously on both FVC and RVC at three frequencies: 5970 Hz, 6000 Hz, or 6030 Hz.
π Definition β VMAC (Voice Mobile Attenuation Code): Instructs the user to transmit at a specific power level.
π Definition β Blank-and-burst signaling: Allows the MSC to send bursty data on voice channels by temporarily omitting speech and SAT and replacing with data.
Mobile to Landline Call:
- Subscriber transmits request (MIN, electronic serial number, station class mark, destination number) on RCC
- BS forwards request to MSC
- MSC checks user registration and connects to PSTN
- Assigns FVC and RVC with SAT and VMAC
During calls, MSC issues blank-and-burst commands to switch between different voice channels on different BS as the user travels. The MSC uses a scanning receiver called a locator in nearby BS to determine RSSI for handoff decisions.
When all voice channels are occupied, the MSC may issue a directed retry to the subscriber on FCC, forcing them to switch to a different control channel or BS, though this may or may not succeed.
AMPS and ETACS Air Interface
The air interface parameters are summarized in the table:
| Parameter | AMPS | ETACS |
|---|---|---|
| Multiple Access | FDMA | FDMA |
| Duplexing | FDD | FDD |
| Channel BW | 30 KHz | 25 KHz |
| Traffic channels per RF channel | 1 | 1 |
| Reverse channel freq | 824-849 MHz | 890-915 MHz |
| Forward channel freq | 869-894 MHz | 935-960 MHz |
| Voice modulation | FM | FM |
| Data rate on control/wideband channel | 10 kbps | 8 kbps |
| Spectral efficiency | 0.33 bps/Hz | 0.33 bps/Hz |
| Number of channels | 832 | 1000 |
Supervisory Signals (SAT and ST Tones)
Supervisory signals allow each user and BS to confirm connection during a call. SAT always exists during use of any voice channel. AMPS and ETACS use three SAT signals at 5970 Hz, 6000 Hz, or 6030 Hz. The BS constantly transmits one of three SAT tones on each voice channel when in use.
When a call is set up:
- SAT is transmitted immediately on FVC
- Subscriber must detect, filter, and demodulate SAT from FVC
- Subscriber reproduces SAT on RVC
- If SAT is not properly detected within one second, both BS and subscriber cease transmission
π‘ Why this matters: SAT ensures that calls are not maintained on incorrect channels or with interfering users, preventing co-channel interference.
π Definition β ST (Signaling Tone): A 10 kbps data burst signaling call termination by the subscriber; contains alternating 1s and 0s sent on RVC for 200 ms. Unlike blank-and-burst messages, ST tone is sent simultaneously with SAT, alerting the system that the user deliberately terminated the call.
Wideband Blank-and-burst Encoding
AMPS voice channels carry wideband (10 kbps) data streams for blank-and-burst signaling. The wideband data stream is encoded using Manchester coding. The advantage is that the energy of the Manchester coded signal is concentrated at the transmission rate frequency of 10 KHz, with little energy leaking into the audio band below 4 KHz.
Narrowband AMPS (N-AMPS)
N-AMPS (Narrowband AMPS) uses 10 KHz channels, allowing three times more users compared to standard AMPS. It uses the same SAT, ST, and blank-and-burst signaling, but with signaling done using sub-audible data streams.
β Key Takeaways
AMPS was the first commercial cellular system using 30 KHz channels in the 800 MHz band with 7-cell reuse pattern requiring 18 dB SIR. The system architecture uses 21 control channels per provider with FDD and FM modulation, while call handling involves paging on FCC, acknowledgments on RCC, and voice channel assignment with SAT and VMAC parameters. Supervisory signals (SAT at three frequencies and ST at 10 kbps) are critical for maintaining call integrity and detecting user-initiated call termination versus system drops. Blank-and-burst signaling using Manchester coding enables handoffs and power control during active calls. N-AMPS evolved the system to 10 KHz channels for threefold capacity increase using sub-audible signaling.
π§ Quick Revision Questions
- What is the frequency separation between forward and reverse channels in AMPS, and why was this specific value chosen?
- How does the call setup procedure differ between a landline-to-mobile call and a mobile-to-landline call in AMPS?
- What are the three SAT frequencies used in AMPS, and what happens if SAT is not detected within one second?
- What is the difference between Signaling Tone (ST) and blank-and-burst signaling in terms of SAT transmission?
- How does N-AMPS achieve three times more capacity than standard AMPS, and what signaling method does it use?
π Lecture 16 β GSM: Global System for Mobile Communication
π Overview: This lecture introduces the Global System for Mobile Communications (GSM), a digital cellular standard that addressed the limitations of analog systems. It covers GSM system architecture, network areas, technical specifications, subscriber services, mobility support, and the identifiers used for routing and subscriber management.
ποΈ Topics Covered
The lecture begins by contrasting analog and digital systems, then introduces GSM's three major subsystems: Switching System (SS), Base Station System (BSS), and Operation and Support System (OSS). It details key network components including MSC, BSC, BTS, HLR, VLR, AUC, EIR, MXE, GMSC, and GIWU, followed by network areas (cell, location area, MSC, PLMN), technical specifications, subscriber services like DTMF, fax, SMS, and voice mail, mobility concepts, the mobile station components (ME and SIM), and the identifiers used in GSM networks.
π Lecture Summary
Review of Last Lecture
The previous lecture covered AMPS (Advanced Mobile Phone System) introduction, system overview, call handling, air interface, supervisory signals, and N-AMPS.
GSM Introduction
Analog cellular systems faced inability to handle growing capacity needs cost-efficiently and were developed without standardized specifications. Digital systems offer ease of signaling, lower interference, integration of transmission and switching, and increased capacity. GSM provides recommendations, not requirements, defining functions and interface requirements in detail without addressing hardware to limit designers.
The GSM network is divided into three major systems:
- Switching System (SS): Responsible for call processing and subscriber-related functions.
- Base Station System (BSS): Performs all radio-related functions, consisting of base station controllers (BSCs) and base transceiver stations (BTSs).
- Operation and Support System (OSS): The functional entity from which the network operator monitors and controls the system, providing cost-effective support for centralized, regional, and local operational and maintenance activities.
GSM System Architecture
Mobile Switching Centre (MSC) The core switching entity in the network, connected to the radio access network (RAN) formed by BSCs and BTSs within the Public Land Mobile Network (PLMN). All calls to and from the user are controlled by the MSC. A GSM network has one or more MSCs, geographically distributed.
Base Station Controller (BSC) Provides all control functions and physical links between the MSC and BTS. It is a high-capacity switch that handles handover, cell configuration data, and control of radio frequency (RF) power levels in base transceiver stations. A number of BSCs are served by an MSC.
Base Transceiver Station (BTS) Handles the radio interface to the mobile station. The BTS contains the radio equipment (transceivers and antennas) needed to service each cell. A group of BTSs are controlled by a BSC.
Home Location Register (HLR) A database used for storage and management of subscriptions, containing a subscriber's service profile, location information, and activity status. When an individual buys a subscription, they are registered in the HLR of that operator.
Visitor Location Register (VLR) A database containing temporary information about subscribers needed by the MSC to service visiting subscribers. The VLR is always integrated with the MSC. For a roaming user, the VLR connected to that MSC requests data about the mobile station from the HLR through the MSC.
Authentication Centre (AUC) Provides authentication and encryption parameters that verify the user's identity and ensure call confidentiality. The AUC protects network operators from fraud.
Equipment Identity Register (EIR) A database containing information about mobile equipment identity that prevents calls from stolen, unauthorized, or defective mobile stations. The AUC and EIR can be implemented as stand-alone nodes or combined.
Message Centre (MXE) Provides integrated voice, fax, and data messaging. Specifically handles short message service (SMS), cell broadcast, voice mail, fax mail, email, and notification.
Gateway Mobile Services Switching Centre (GMSC) A node used to interconnect two networks. The gateway is often implemented in an MSC, which is then referred to as the GMSC.
GSM Inter-working Unit (GIWU) Consists of hardware and software providing an interface to various networks for data communications. Through the GIWU, users can alternate between speech and data during the same call. The GIWU hardware is physically located at the MSC/VLR.
GSM Network Areas
- Cell: Identified by cell global identity (CGI)
- Location Area (LA): Group of cells, identified by LAI
- MSC: Service area of one MSC
- Public Land Mobile Network (PLMN): Service area of one operator
Specifications
- Frequency band: 1,850 to 1,990 MHz (mobile station to base station)
- Duplex distance: 80 MHz
- Channel bandwidth: 200 kHz
- Modulation: Gaussian minimum shift keying (GMSK)
- Transmission rate: Over-the-air bit rate of 270 kbps
- Access method: Time division multiple access (TDMA)
- Speech coder: Uses linear predictive coding (LPC), speech encoded at 13 kbps
Subscriber Services
Two basic types of services: Telephony (tele-services) for voice communication, and Data (bearer services) for transmitting data signals between access points.
Dual-tone multi-frequency (DTMF): A tone signalling scheme used for various control purposes via the telephone network, such as remote control of an answering machine.
Facsimile group III: GSM supports CCITT Group 3 facsimile. Special fax converters connected to the exchange allow GSM-connected faxes to communicate with any analog fax in the network.
Short message services (SMS): A message of a maximum of 160 alphanumeric characters can be sent to or from a mobile station. If the subscriber's mobile unit is powered off or out of coverage, the message is stored and delivered when the mobile is powered on or re-enters coverage.
Cell broadcast: A variation of SMS, broadcasting a message of a maximum of 93 characters to all mobile subscribers in a certain geographic area. Typical applications include traffic congestion warnings and accident reports.
Voice mail: An answering machine within the network controlled by the subscriber. Calls can be forwarded to the subscriber's voice-mail box, and the subscriber checks messages via a personal security code.
Fax mail: The subscriber can receive fax messages at any fax machine. Messages are stored in a service centre and retrieved via a personal security code to the desired fax number.
GSM Mobility
Roaming in GSM is made possible through the separation of switching capability and subscription data. A subscriber's data is permanently registered in the HLR in their Home PLMN (HPLMN). The MSC and GMSC are not specific to one subscriber group.
π‘ Why this matters: This separation allows subscribers to use their mobile service in networks other than their home network, which is the foundation of international roaming.
Mobile Station
Consists of two components:
- Mobile Equipment (ME): The physical device
- Subscriber Identification Module (SIM): A chip in the SIM card that identifies a subscriber of a GSM network. When inserted in the ME, the subscriber may register with a GSM network, personalizing the ME. The SIM card contains information such as IMSI, advice of charge parameters, and operator-specific emergency numbers.
Identifiers in the GSM Network
GSM uses several identifiers for routing calls, identifying subscribers (e.g., for charging), locating the HLR, and identifying equipment.
International Mobile Subscriber Identity (IMSI) π Definition β IMSI: A unique identifier embedded on the SIM card used to identify a subscriber. It is also contained in the subscription data in the HLR. For roaming charging, a VPLMN (Visited PLMN) uses the IMSI to send billing records to the HPLMN of a subscriber.
β Key Takeaways
GSM is a digital cellular standard that overcame analog system limitations by using digital signaling, lower interference, and standardized specifications. The network architecture consists of three main systems: SS, BSS, and OSS, with key components including MSC, BSC, BTS, HLR, VLR, AUC, EIR, MXE, GMSC, and GIWU. GSM uses TDMA with GMSK modulation, 200 kHz channels, and a transmission rate of 270 kbps. Important subscriber services include SMS (160 characters), cell broadcast (93 characters), DTMF, fax, and voice/fax mail. Mobility is enabled through the separation of switching and subscription data, with the SIM card storing the IMSI for subscriber identification and roaming charging.
π§ Quick Revision Questions
- What are the three major systems in the GSM network architecture, and what is the primary function of each?
- What is the difference between an HLR and a VLR, and how do they interact during roaming?
- What are the technical specifications of GSM including frequency band, channel bandwidth, modulation, transmission rate, and access method?
- How does SMS work when a mobile subscriber is powered off or out of coverage?
- What is the IMSI and how is it used for roaming charging between VPLMN and HPLMN?
π Lecture 17 β GPRS: General Packet Radio Service (Part I)
π Overview: This lecture introduces GPRS (General Packet Radio Service), a major enhancement over GSM that enables packet-switched data services. It covers GPRS architecture, the new network nodes called GSNs, how mobile devices register and manage sessions, and the classification of channels used for data transmission. Understanding GPRS is essential because it bridges circuit-switched cellular networks to the packet-switched Internet.
ποΈ Topics Covered
The lecture begins with a review of GSM identifiers and call routing, then introduces GPRS as a packet-switched enhancement. It details the GPRS architecture including A/Gb and Iu modes, BSS upgrades with PCU, mobile registration (attach/detach), session management via PDP context activation, physical channel classification into shared/dedicated/packet data channels, and logical channel types for control and user data.
π Lecture Summary
Review of last lecture
The previous lecture covered GSM system architecture, network areas, subscriber services (DTMF, fax, SMS, cell broadcast, voice/fax mail), mobility, and key identifiers. GSM uses several identifiers for routing calls, identifying subscribers, locating the HLR, and identifying equipment.
Identifiers in GSM Network and Call Routing
International Mobile Subscriber Identity (IMSI) is embedded on the SIM card and used to identify a subscriber. It is also contained in the subscription data in the HLR.
International Mobile Equipment Identifier (IMEI) is a unique number hard-coded in the ME that cannot be modified. It is used to identify the mobile equipment.
Mobile Station Roaming Number (MSRN) is used in the GSM network for routing a call to an MS. The MSRN is allocated to a subscriber during MT call handling and is released when the call is established. Each MSC in a PLMN has a limited range of MSRNs allocated to it.
Mobile Station Integrated Services Digital Network Number (MSISDN) is used to identify the subscriber when establishing a call or sending an SMS. The MSISDN is not stored on the subscriber's SIM card and is normally not available in the MS. It is provisioned in the HLR as part of the subscriber's profile and sent to MSC during registration.
π Definition β IMSI: A unique identifier embedded on the SIM card used to identify a subscriber in the GSM network.
π Definition β IMEI: A unique, non-modifiable identifier hard-coded in the mobile equipment used to identify the device itself.
π Definition β MSRN: A temporary number allocated to a subscriber during mobile-terminated call handling for routing the call to the MS.
π Definition β MSISDN: The telephone number used to identify a subscriber for call establishment and SMS delivery, provisioned in the HLR.
Introduction to GPRS
GPRS is an enhancement over GSM that adds nodes called GSNs (GPRS Support Nodes) to provide packet-switched services. These nodes are responsible for routing and delivery of data packets to and from the MS and external packet data networks (PDN) .
The goals of GPRS are: efficient bandwidth usage for bursty data traffic (e.g., Internet), higher data rates, and new charging models. GPRS was initially specified by ETSI with multiple releases (R97, R98, R99, R4), then handed over to 3GPP. The lecture considers Release 5 and Release 6.
GPRS Release 5/6 determines two modes based on core network generation: 2G core uses A/Gb mode, and 3G core uses Iu mode. The Iu interface was added in Release 5 to align with UMTS.
GPRS Architecture
The GERAN Reference Architecture shows the network elements. In A/Gb mode, there are three classes of mobile stations: Class A can operate simultaneous packet switched and circuit switched services; Class B can operate either one at a time (most common for handsets today); Class C can operate only packet switched services (e.g., expansion cards for laptops).
In Iu mode, the modes are: CS/PS mode (same as Class A in A/Gb mode), PS mode (MS can only operate packet switched services), and CS mode (MS can only operate circuit switched services).
Service types include Point-to-Point (e.g., Internet access by user) and Point-to-Multipoint (e.g., delivery of information like news to multiple locations or interactive conference applications).
π Definition β Class A (A/Gb): A mobile station capable of simultaneous packet-switched and circuit-switched services.
π Definition β Class B (A/Gb): A mobile station that can operate either packet-switched or circuit-switched services, but not simultaneously.
π Definition β Class C (A/Gb): A mobile station that can only operate packet-switched services.
Registration and Session Management
For GPRS BSS, a software upgrade is required in the existing Base Transceiver Site (BTS) . The Base Station Controller (BSC) also requires a software upgrade and installation of a new hardware called packet control unit (PCU) . The PCU directs data traffic to the GPRS network and provides a physical and logical data interface out of BSS for packet data traffic.
Registration of a Mobile Node requires the MS to register with the GPRS network through GPRS attach. The device sends a message to the new SGSN containing the last assigned Temporary Mobile Subscriber Id (TMSI) and location area information. The new SGSN queries the old SGSN for the identity of this mobile device, then requests more information for authentication. GPRS detach can be initiated by the MS or the network.
Session Management begins after successful attach. To start packet data, the MS must activate a Packet Data Protocol (PDP) address. This address is unique only for a particular session and consists of: PDP type, PDP address assigned to MS, and requested QoS. Once PDP Context is activated, a two-way tunnel is established between the device's current SGSN and the corresponding GGSN. The GGSN hides the mobility from onward networks.
PDP-Address allocation can be static (assigned by network operator of user's home PLMN) or dynamic (assigned by the corresponding GGSN).
π Definition β PCU: A hardware element associated with BSC that directs data traffic to the GPRS network.
π Definition β PDP Context: An active session between the MS and GGSN that defines the PDP type, address, and QoS for packet data transfer.
π Definition β PDP Address: A unique address assigned for a particular packet data session, which can be static or dynamic.
π Example: When a mobile user wants to browse the Internet, the MS first performs GPRS attach to register with the SGSN. Then it initiates PDP Context Activation with parameters like PDP type = IP, requested QoS = best effort. The GGSN assigns a dynamic IP address, and a tunnel is established between SGSN and GGSN for the session.
Routing Scenario in GPRS
[Note: The lecture text indicates this topic is listed in the outline but the detailed routing scenario content is not provided in the transcript. Only the diagram reference and citation were given.]
Channels Classification
Physical Channels are defined by timeslot (0-7) and radio frequency channel. There are Shared Basic Physical Sub Channels (shared among up to 8 users) and Dedicated Basic Physical Sub Channels (one user). A Packet Data Channel (PDCH) is dedicated to packet data traffic from logical channels for both control and user data.
π Definition β PDCH: A physical channel dedicated to carrying packet data traffic from logical control and user data channels.
β Key Takeaways
The most critical concepts from this lecture are the GSM identifiers (IMSI, IMEI, MSRN, MSISDN) and their distinct roles in subscriber identification, equipment identification, and call routing. GPRS architecture introduces new nodes called GSNs (SGSN and GGSN) with the PCU at the BSS level to enable packet switching. Mobile registration involves GPRS attach with TMSI verification, while session management requires PDP Context Activation to establish tunnels between SGSN and GGSN. MS classes in A/Gb mode (A, B, C) define whether devices can handle simultaneous circuit and packet services. Finally, physical channels are divided into shared/dedicated sub-channels, with PDCH being exclusively for packet data traffic.
π§ Quick Revision Questions
- What are the four main identifiers used in GSM networks, and what is the specific purpose of each?
- During GPRS attach, what information does the MS send to the new SGSN, and how does the new SGSN verify the device identity?
- What are the three components that make up a PDP address during session management?
- In A/Gb mode, what is the difference between Class A and Class B mobile stations?
- What is a PDCH, and how does it differ from a shared basic physical sub-channel?
π Lecture 18 β GPRS: General Packet Radio Service (Part II)
π Overview: This lecture continues the study of GPRS by diving into its detailed protocol architecture, air interface design, and mobility management. It explains how data is routed and transferred in both uplink and downlink directions, and how quality of service (QoS) is supported for packet-switched services. This matters because GPRS was a foundational technology for mobile data, bridging GSM circuit-switched voice with IP-based packet data.
ποΈ Topics Covered
This lecture covers the full GPRS protocol stack from the transmission and signaling planes, including Radio Link Control (RLC) and Media Access Control (MAC) sublayers. It explains the GPRS air interface using a master-slave PDCH concept with capacity on demand, details the procedures for uplink and downlink data transfer, describes the three mobility states (Idle, Standby, Active), and outlines QoS profiles with service precedence, reliability, delay, and throughput parameters.
π Lecture Summary
GPRS Protocol Architecture
The GPRS protocol stack is divided into two planes. The Transmission Plane provides protocols for the transmission of user data and its associated signaling. The Signaling Plane comprises protocols for controlling and supporting the functions of the transmission plane.
π Transmission Plane: The protocols used for actually moving user data packets.
- GPRS Backbone (SGSN β GGSN): Uses GTP (GPRS Tunneling Protocol) to tunnel user packets and related signaling information between GPRS support nodes.
- Sub-network dependent convergence protocol (SNDCP): Used to transfer packets between SGSN and MS.
- Data link layer: Consists of LLC (Logical Link Control) between MS and SGSN, and RLC/MAC between MS and BSS.
- Physical layer:
- PLL (Physical Link Layer): responsible for channel coding, detection of errors, forward error correction, interleaving, and detection of physical link congestion.
- RFL (Radio Frequency Layer): handles modulation and demodulation.
Radio Link Control (RLC)
The RLC sublayer provides reliability for MAC transmissions and operates in three modes.
- Transparent mode: No functionality.
- Acknowledged mode: Uses Selective Repeat ARQ, with a sender window at the transmitter and Uplink ACK/NACK or Downlink ACK/NACK at the receiver.
- Unacknowledged mode: Controlled by numbering within a TBF (Temporary Block Flow). No retransmissions are performed; missing packets are replaced with dummy information bits.
Media Access Control (MAC)
The MAC sublayer performs contention resolution between channel access attempts and is connection-oriented.
- Temporary Block Flow (TBF): A logical unidirectional connection between two MAC entities that is allocated resources on PDCH(s) (Packet Data Channels). The Temporary Flow Identity (TFI) is unique among concurrent TBFs in the same direction.
MAC: Channel Access & Resource Allocation
- Slotted Aloha: Used in the PRACH channel. MSs send packets in the uplink direction at the beginning of a time slot. If a collision occurs, the MS backs off using an arbitrary timer and then re-transmits.
- Time Division Multiple Access (TDMA): Predefined slots are allocated by the BSS, providing contention-free channel access.
GPRS Air Interface
The air interface uses a master-slave concept. One PDCH acts as the Master and holds all PCCCH (Packet Common Control Channel) channels. The rest of the channels act as Slaves. This design enables capacity on demand: PDCH(s) are increased or decreased according to demand, with load supervision performed in the MAC Layer.
π PCCCH (Packet Common Control Channel): A set of control channels that GPRS mobiles camp on when allocated in a cell. It includes PRACH (Random Access), PPCH (Paging), PAGCH (Access Grant), and PNCH (Packet Notification for multicast). π PDCCH (Packet Dedicated Control Channel): Includes SACCH (Slow Associated Control Channel) for radio measurements and power control, FACCH (Fast Associated Control Channel) for acknowledgment on a TCH, and SDCCH (Stand-alone Dedicated Control Channel) for reliable signaling and SMS. π PBCCH (Packet Broadcast Control Channel): Contains frequency correction channels for synchronizing the MS's Local Oscillator to the BS, a synchronization channel, and a broadcast control channel for general base station information.
π‘ Why this matters: The master-slave PDCH concept was a key innovation allowing GPRS to dynamically share radio resources between voice and data traffic without requiring dedicated data channels.
Uplink Data Transfer
[The lecture text contains a diagram reference but no textual explanation for the uplink procedure. The summary is derived from context and the standard GPRS procedure.] In uplink data transfer, the MS initiates a packet transfer request on the PRACH using Slotted Aloha. The BSS responds with resource assignment on the PAGCH, allocating a TBF and TFI. The MS then transmits data blocks on the allocated uplink PDCHs using the assigned TBF. The BSS can send uplink ACK/NACK messages to the MS for error recovery.
Downlink Data Transfer
[The lecture text contains a diagram reference but no textual explanation for the downlink procedure. The summary is derived from context and the standard GPRS procedure.] For downlink data transfer, the SGSN receives packets from the GGSN and forwards them to the BSS. The BSS pages the MS on the PPCH if the MS is in standby state. Once the MS responds, the BSS assigns a downlink TBF on the PAGCH and transmits data blocks. The MS sends downlink ACK/NACK to the BSS for selective retransmission.
Mobility
A GPRS mobile station operates in three states:
- Idle: The MS does not have a logical GPRS context activated or any PSPDN (Packet-Switched Public Data Network) addresses allocated. It can only receive multicast messages available to any GPRS mobile.
- Standby: The location of the MS is known only to which routing area it belongs.
- Active: The SGSN knows the cell-level location of the mobile station. Data is transmitted between the MS and the GPRS network only in this state.
π‘ Why this matters: These states allow GPRS to conserve radio and network resources by tracking mobile stations with different granularity based on their activity level.
QoS in GPRS
GPRS assumes that IP multimedia applications can define their requirements, negotiate their capabilities, and identify and select available media components. GPRS specifies signaling that enables support for various traffic streams, including constant/variable bit rate and connection oriented/connectionless services.
QoS Profile for GPRS Bearers The QoS profile is defined by four parameters:
- Service precedence: 3 classes (high, normal, low).
- Reliability parameter: 3 classes.
- Delay parameters: 4 classes.
- Throughput parameter: maximum and mean bit rates.
The QoS profile is included in the Packet Data Protocol (PDP) context, and negotiation is managed through PDP procedures (activation, modification, and deactivation).
π PDP Context: A data structure that contains the subscriber's session information, including the IP address, QoS profile, and connection parameters, when the MS is attached to the GPRS network.
β Key Takeaways
GPRS uses a layered protocol architecture with a transmission plane (GTP, SNDCP, LLC, RLC/MAC, physical) and a signaling plane. The air interface employs a master-slave PDCH concept with capacity on demand, using Slotted Aloha for contention-based uplink access on PRACH and TDMA for contention-free allocated slots. RLC provides reliability through Selective Repeat ARQ in acknowledged mode, while MAC manages TBFs as logical unidirectional connections. Mobility is managed through three states (Idle, Standby, Active) that determine tracking granularity and data transmission capability. Finally, GPRS supports four QoS parameters (precedence, reliability, delay, throughput) negotiated through PDP context procedures, enabling support for diverse traffic streams.
π§ Quick Revision Questions
- What are the two planes in the GPRS protocol architecture, and what is the primary function of each?
- What are the three modes of RLC operation, and how does acknowledged mode handle errors?
- Explain the master-slave concept in the GPRS air interface and what channel each uses.
- In which GPRS mobility state does the SGSN know the cell location of the MS?
- What are the four parameters of a GPRS QoS profile, and how are they negotiated?
π Lecture 19 β cdmaOne/IS-95
π Overview: This lecture covers the transition from TDMA-based IS-136 to the CDMA-based IS-95 (cdmaOne) standard, a key 2G wireless technology. It explains the fundamental principles of CDMA, its advantages and drawbacks, and provides a detailed breakdown of both forward and reverse channel structures in IS-95, which laid the groundwork for 3G systems.
ποΈ Topics Covered
The lecture begins with a recap of IS-136 (TDMA-based) and its specifications. It then defines CDMA as both an access method and air interface, outlining its three main systems (IS-95, W-CDMA, CDMA2000). The advantages and drawbacks of CDMA cellular systems are discussed, followed by a detailed examination of the IS-95 forward channels (Pilot, Sync, Paging, Traffic) and their specific roles. Finally, the forward link transmission process for voice traffic is explained.
π Lecture Summary
Last Lecture
The previous lecture covered the GPRS Protocol Architecture including interfaces between MS-BSS, BSS-SGSN, SGSN-GGSN, and GGSN-PDN. It also discussed the GPRS Air Interface, data routing and mobility management for both uplink and downlink data transfer, and Quality of Service (QoS) in GPRS.
IS-136
IS-136 is an evolution of the AMPS standard, based on TDMA (Time Division Multiple Access) technology. It operates in the 800 / 1900 MHz band and uses TDMA frames of 6 time slots, each 40 ms in length. The system supports a half-rate channel using 1 slot and a double-rate channel using 4 slots.
IS-136 Channels include the Digital Control Channel (DCCH) which occupies a full rate channel (2 time slots) and is divided into logical channels: SPACH (SMS point-to-point, paging and access response channel), BCCH (Broadcast Control Channel), SCF (Shared Channel Feedback), and RACCH (Random Access Control Channel).
π Definition β IS-136: A 2G digital cellular standard based on TDMA/FDD, operating in the 800/1900 MHz bands with a channel bandwidth of 30 kHz and a data rate of 48.6 kb/s.
π Formula: Spectrum Efficiency = 48.6 kb/s / 30 kHz = 1.62 b/s/Hz
π Example: In IS-136, the forward channel frequency band is 869 β 894 MHz, the reverse channel is 824 β 849 MHz, and each channel supports 3 or 6 users per channel using 6 time slots.
What is CDMA
CDMA (Code Division Multiple Access) is both an access method and an air-interface. The rest of the network (radio resource management, mobility management, security) is very similar to other systems, but power control and handoffs are different. CDMA uses DSSS (Direct Sequence Spread Spectrum) and has a frequency reuse factor of 1, meaning all cells use the same frequency. The three main CDMA systems are IS-95 (2G), W-CDMA, and CDMA2000. π‘ Why this matters: The frequency reuse factor of 1 is a major advantage over TDMA/FDMA systems, dramatically increasing spectral efficiency.
Advantages of CDMA Cellular
CDMA offers higher capacity, improved voice quality (using a new coder), and less power consumption (6-7 mW). It was the choice for 3G systems because it provides frequency diversity (frequency-dependent transmission impairments have less effect on the signal) and multipath resistance (chipping codes exhibit low cross-correlation and low autocorrelation). CDMA also provides inherent privacy (spread spectrum uses noise-like signals) and graceful degradation (the system only gradually degrades as more users access the system).
Drawbacks of CDMA Cellular
Key drawbacks include self-jamming (arriving transmissions from multiple users not aligned on chip boundaries unless perfectly synchronized), the near-far problem (signals closer to the receiver are received with less attenuation than signals farther away), and soft handoff (the mobile must acquire the new cell before relinquishing the old one, which is more complex than hard handoff). Additionally, the CDMA air-interface is the most complex.
Mobile Wireless CDMA Design Considerations
The RAKE receiver is a critical design component. When multiple versions of a signal arrive more than one chip interval apart, the RAKE receiver attempts to recover signals from multiple paths and combine them. This method achieves better performance than simply recovering the dominant signal and treating remaining signals as noise.
IS-95 CDMA Forward Channel
The forward link uses the same frequency spectrum as AMPS (824-849 MHz). There are 4 types of logical channels: one pilot, one synchronization, seven paging, and 55 traffic channels. The modulation scheme is QPSK. Orthogonal Walsh codes (64 total, 64 chips per bit) are used for channel separation. After orthogonal coding, signals are further spread by short PN spreading codes. π‘ Why this matters: The 64 Walsh codes allow 64 simultaneous logical channels on the same frequency, enabling the high capacity of CDMA.
Forward Channels
The Pilot Channel
The pilot channel is a continuous signal on a single channel. It allows the MS (Mobile Station) to acquire timing information, provides a phase reference for demodulation, and a means for signal strength comparison. It is 4-6 dB stronger than all other channels. The pilot channel is obtained using the all-zero Walsh code (W0) and contains no information except the RF carrier. There is no power control on the pilot channel.
Sync Channel
The sync channel is used to acquire initial time synchronization. The sync message includes the system ID (SID), network ID (NID), the offset of the PN short code, the state of the PN-long code, and the paging channel data rate (4.8 or 9.6 Kbps). It uses W32 for spreading and operates at 1200 bps.
Paging Channel
The paging channel uses W1-W7 and has no power control. It is additionally scrambled by the PN long code, which is generated by an LFSR (Linear Feedback Shift Register) of length 42. The data rate is either 4.8 Kbps or 9.6 Kbps.
Traffic Channels
Traffic channels carry user information. There are two possible data rate sets: RS1 = {9.6, 4.8, 2.4, 1.2 Kbps} and RS2 = {14.4, 7.2, 3.6, 1.8 Kbps}. RS1 is mandatory for IS-95, while RS2 support is optional. Traffic channels also carry power control bits for the reverse channel.
Forward Link Transmission
For voice traffic, speech is encoded at 8550 bps, and after adding error detection bits, it becomes 9600 bps. The full channel capacity is not used when the user is not speaking: during quiet periods, the data rate drops to 1200 bps; 2400 bps is used for background noise transients; 4800 bps mixes digitized speech and signaling data.
π Example: Digitized speech is transmitted in 20 ms blocks with FEC rate Β½, making the effective data rate a maximum of 19.2 kbps. This resulting stream is then XORed with the Walsh code, generating data at 1.2288 Mbps (19.2 kbps Γ 64 chips/bit = 1.2288 Mcps, the chip rate).
β Key Takeaways
The most critical concepts from this lecture are the fundamental difference between IS-136 (TDMA/FDD) and IS-95 (CDMA with reuse factor 1), and the detailed structure of IS-95's forward channels. You must remember the four forward channel types (Pilot, Sync, Paging, Traffic), their specific Walsh codes, data rates, and functions. The pilot channel provides synchronization without data; the sync channel uses W32 at 1200 bps for initial timing; paging uses W1-W7 for overhead; and traffic channels support mandatory RS1 data rates. The RAKE receiver's role in combating multipath fading is essential, as is understanding the voice transmission process from 8550 bps speech coding to 1.2288 Mbps chip rate after Walsh spreading.
π§ Quick Revision Questions
- What is the frequency reuse factor in IS-95 CDMA, and why is it significant?
- Name the four types of logical channels in the IS-95 forward link and their respective Walsh code assignments.
- What information is contained in the sync channel message?
- Explain how the RAKE receiver improves performance in a CDMA system.
- Describe the step-by-step process of how voice data at 8550 bps becomes a 1.2288 Mbps signal in the forward link transmission.