π Lecture 23 β WCDMA (Part III)
π Overview: This lecture covers the final aspects of WCDMA, focusing on compressed mode measurements for inter-frequency handovers, handover procedures across different modes and systems, and the mechanisms for packet data access. It also details the transport channels used for packet data and the scheduling algorithms that manage radio resources, which are critical for efficient network performance.
ποΈ Topics Covered
This lecture begins with compressed mode measurements, explaining the need for transmission gaps and methods for achieving them. It then covers handover measurements, including intra-mode, inter-mode, and inter-system handovers. The discussion moves to WCDMA packet data access, describing traffic classes and packet data characteristics. The lecture details transport channels for packet data, including common, dedicated, and shared channels. Finally, it covers packet scheduling algorithms, specifically time division, code division, and transmission power-based scheduling.
π Lecture Summary
Compressed Mode Measurements
Compressed mode is needed when a terminal, without a full dual receiver, must make measurements on another frequency. The goal is not to lose data but to compress it. Transmission and reception are halted for a short time to perform measurements on other frequencies. Three methods for compressed mode are: lowering the data rate from higher layers; increasing the data rate by changing the spreading factor; and reducing the symbol rate by puncturing at the physical layer multiplexing chain. More power is needed during compressed mode. No power control is active during the compressed frame; a large step size is used after the frame to allow the power level to converge quickly.
π Definition β Transmission Gap Length (TGL): The duration of the measurement gap in slots. The specified TGLs are 3, 4, 7, 10, and 14 slots. TGLs of 3, 4, and 7 can be obtained with both single and double frame methods, while TGLs of 10 or 14 only use the double frame method to minimize impact during a single frame. Very short TGLs (1 or 2) are excluded because the hardware needs time to switch frequencies. π Example: A terminal needing to measure a GSM cell on a different frequency would activate compressed mode, creating a transmission gap of, for example, 7 slots to perform the measurement. During this gap, its data transmission is halted and then resumed with higher power afterwards.
Handover measurements
Handover measurements are categorized into three types. Intra-mode handover includes soft handover, softer handover, and hard handover. Inter-mode handover is a handover to the UTRA TDD mode. Inter-system handover is a handover to another system, such as GSM.
π‘ Why this matters: These categories define how a mobile device connects to different cells and technologies, which is fundamental for seamless mobility in a heterogeneous network.
Intra-Mode Handover
Intra-mode handover relies on Ec/No measurements performed from the CPICH. The quantities measured from the CPICH are: Received Signal Code Power (RSCP) , the received power on one code after de-spreading; RSSI, the wideband received power within the channel bandwidth; and Ec/No, which represents RSCP/RSSI. For soft handover, relative timing between cells is needed for coherent combining in the RAKE receiver. If cells are within a 10ms window, the relative timing can be found from the primary scrambling code phase; otherwise, terminals must decode the System Frame Number from the primary CCPCH. For hard handover, timing information is not needed, and different frequency measurements can be done with the aid of compressed mode.
π Definition β Ec/No: A measure of signal quality, calculated as the ratio of the received signal code power (RSCP) to the total received power (RSSI). π Example: A terminal monitoring its serving cell and a neighboring cell measures the CPICH Ec/No of both. If the neighboring cell's Ec/No exceeds a threshold relative to the serving cell's, the terminal triggers a measurement report to initiate a soft handover.
Packet Data Access
There are four basic types of traffic classes. Conversational class is real-time, for human-to-human interaction, with very low delay and near symmetry (e.g., speech). Streaming class is real-time, transferring data as a steady, continuous stream with low delay and asymmetry (e.g., video). Interactive class is non-real-time packet data where a response is requested, requiring reasonable round-trip delay (e.g., Web browsing). Background class is non-real-time packet data with no immediate action expected and is less sensitive to delivery time (e.g., e-mail).
π Definition β Packet Data Traffic: Non-real-time packet services, including Interactive and Background traffic classes. Properties include bursty data, tolerance for longer delays, and the ability to allow high frame error rates with low transmission power due to retransmission services at the radio link control layer. π Example: A user browsing the web generates interactive class traffic. When they click a link, a packet call is initiated, resulting in a burst of data transfer. After the page loads, a reading time begins, during which no data is sent, demonstrating the bursty nature of the traffic.
Transport Channels for Data Packet Access
Transport channels for packet data include common, dedicated, and shared channels. Common channels (RACH in uplink, FACH in downlink) have low setup time but no feedback channel, meaning no fast closed-loop power control or soft handover, which leads to poor link-level performance. They are suitable for small data amounts. Dedicated channels (DCH) use fast power control and soft handover, have a longer setup time, and can support up to 2 Mbps. They are suitable for large data amounts but not for bursty data, as the downlink orthogonal code is reserved according to the maximum bit rate. Shared channels allow a single orthogonal code to be shared with many packet users in a time-division manner, making it code-efficient. They allow fast allocation and rate modification on a frame-by-frame basis, are suitable for large and bursty data, and use fast power control but no soft handover.
π‘ Why this matters: Choosing the correct transport channel is crucial for efficiently managing radio resources based on the traffic's characteristics, balancing speed, interference, and resource usage.
Packet Scheduling Algorithms
Packet scheduling in WCDMA can be done in a time or code division manner. Time division scheduling allocates a channel to one user at a time (e.g., one 10 ms frame), giving that user all available capacity for a high data rate for a short period. Code division scheduling allocates channels to many users simultaneously, giving each a low data rate for a long period.
Time Division Scheduling
Time division scheduling offers advantages such as requiring less energy per bit due to the high bit rate, generating less interference, and providing shorter delay.
π Definition β Time Division Scheduling: A method where one user is allocated all available channel capacity at a time, resulting in high data rates for short periods. π Example: In a system, User A receives data at 2 Mbps for 10 ms, followed by User B receiving data at 2 Mbps for the next 10 ms. This is efficient for users who can tolerate short bursts of high-speed data.
Code Division Scheduling
Code division scheduling allows resources to be in full usage due to longer transmission times and results in small variations in the interference level.
π Definition β Code Division Scheduling: A method where many users are allocated channels simultaneously, each receiving a low data rate for a longer period. π Example: Users A, B, and C each receive data at 0.67 Mbps simultaneously over a longer period. This is suitable for background traffic like email downloads.
Transmission Power-based Scheduling
Transmission power-based scheduling allocates resources based on user proximity to the base station. Users close to the BS require less transmission power and can get a higher bit rate, while users at the cell edge get a lower bit rate. Advantages include minimizing the average power sent per bit, less interference, and increased throughput. Disadvantages include the need for accurate power estimation and potentially unfair resource allocation.
π Definition β Transmission Power-based Scheduling: A scheduling algorithm that allocates higher bit rates to users requiring less transmission power (typically those close to the base station), thereby optimizing overall system capacity. π Example: A user near the cell center might be scheduled at 1 Mbps, while a user at the cell edge is scheduled at 128 kbps because the cell-edge user would require significantly more power to achieve a higher bit rate, creating more interference.
β Key Takeaways
Students must understand that compressed mode is essential for inter-frequency measurements in terminals without dual receivers, using transmission gap lengths (TGLs) of 3, 4, 7, 10, or 14 slots. The three types of handover measurementsβintra-mode (soft/softer/hard), inter-mode (FDD to TDD), and inter-system (to GSM)βare fundamental for mobility. Packet data traffic is bursty, delay-tolerant, and can be served by different transport channels; common channels are for small data, dedicated channels for steady large data, and shared channels for bursty large data. Finally, packet scheduling can be time-division (high rate, short time), code-division (low rate, long time), or transmission-power-based (prioritizes users with better channel conditions), each with distinct trade-offs for throughput, interference, and fairness.
π§ Quick Revision Questions
- What is the primary purpose of compressed mode in WCDMA, and name two methods used to achieve it?
- How are intra-mode and inter-system handovers different in terms of the measurements required and the systems involved?
- A user is downloading a large file and sending a short status email. Which transport channel (common, dedicated, or shared) is best suited for each activity, and why?
- Explain the fundamental trade-off between time-division and code-division packet scheduling algorithms in terms of data rate, interference, and resource usage.
- In transmission power-based scheduling, why is it advantageous to allocate high bit rates to users near the base station, and what is a key disadvantage of this approach?
π Lecture 24 β CDMA2000
π Overview: This lecture introduces CDMA2000, the 3G evolution of 2G CDMA technology, providing a seamless and cost-effective upgrade path. It covers the new MAC and physical layer features, physical channel structures, and the new network elements like PCF and PDSN required for packet data services. The lecture also details mobility management and handoff procedures specific to CDMA2000 networks.
ποΈ Topics Covered
The lecture begins with a review of compressed mode measurements, handover measurements, WCDMA packet data access, transport channels, and packet scheduling algorithms. It then introduces CDMA2000, explaining its 1xRTT and 3xRTT variants and comparing them to W-CDMA. New MAC and physical layer features such as link adaptation, hybrid ARQ, and turbo codes are discussed, followed by details of the physical layer, radio configurations, and reverse physical channels. New network elements including Packet Control Function (PCF), Packet Data Serving Node (PDSN), Home Agent, and AAA are explained, along with mobility management procedures and three types of handoff: Intra-PCF, Inter-PCF/Intra-PDSN, and Inter-PDSN.
π Lecture Summary
Last lecture review
The previous lecture covered compressed mode measurements and handover measurements including intra-mode, inter-mode, and inter-system handovers. It discussed WCDMA packet data access and transport channels for packet data (common, dedicated, and shared). Finally, packet scheduling algorithms were reviewed: time division scheduling, code division scheduling, and transmission power-based scheduling.
CDMA2000 Introduction
CDMA2000 provides a seamless and evolutionary upgrade path for 2G and 2.5G CDMA technology. It centers on the original 1.25 MHz radio channel, allowing CDMA operators to selectively upgrade without changing entire base station equipment. The first 3G CDMA standard is cdma2000 1xRTT, using a single channel (1x means multi-carrier).
π Definition β cdma2000 1x: Supports data rates up to 307 kbps in packet mode and can support up to twice as many users as 2G CDMA. Cdma 1xEV-DO dedicates the channel strictly to data users and supports 2.4 Mbps per channel.
Cdma2000 3xRTT is the ultimate 3G solution relying on multicarrier that gangs adjacent channels together into 3.75 MHz. Three non-adjacent channels may be operated simultaneously and in parallel, providing data rates in excess of 2 Mbps, similar to W-CDMA. Advocates of cdma2000 claim their standard offers a much more seamless and less expensive upgrade path compared to W-CDMA.
The lecture provides a comparison table:
| Parameter | W-CDMA | cdma2000 |
|---|---|---|
| Carrier spacing | 5 MHz | 3.75 MHz |
| Chip rate | 4.096 MHz | 3.6864 MHz |
| Data modulation | BPSK | FW β QPSK; RV - BPSK |
| Spreading | Complex (OQPSK) | Complex (OQPSK) |
| Power control frequency | 1500 Hz | 800 Hz |
| Variable data rate implement. | Variable SF; multi code | Repet., puncturing, multi code |
| Frame duration | 10 ms | 20 ms (also 5, 30, 40) |
| Coding | Turbo and convolutional | Turbo and convolutional |
| Base stations synchronized? | Asynchronous | Synchronous |
| Base station acquisition/detect | 3 step; slot, frame, code | Time shifted PN correlation |
| Forward link pilot | TDM dedicated pilot | CDM common pilot |
| Antenna beam forming | TDM dedicated pilot | Auxiliary pilot |
New MAC and Physical layer features
The new features and techniques include: Link adaptation based on adaptive modulation, coding and spreading; Physical layer fast hybrid ARQ; Enhanced channel coding and turbo codes; Space and antenna diversity; and Fast forward link power control and coherent uplink demodulation.
Physical Layer of cdma2000
The cdma2000 air interface is designed to provide a flexible framework for supporting voice and other circuit-switched data as well as bursty packet data bearer services with different QoS. It supports RF channel bandwidth of SR Γ 1.25 MHz, where currently SR = 1 and 3 are supported, extendable to 6, 9, and 12. A number of fixed and variable rate physical channels are defined with new variable-length spreading codes and PN codes.
π Definition β Radio Configurations (RCs): Specify the data rate, channel encoding, and modulation parameters. For SR1 and SR3, there are 7 RCs for reverse link and 9 for forward link.
The table shows data rates for different RCs:
| SR | Forward RC | Data Rate (Base, Peak) | Reverse RC | Data Rate (Base, Peak) |
|---|---|---|---|---|
| SR1 | RC1 | 9.6 | RC1 | 9.6 |
| RC2 | 14.4 | RC2 | 14.4 | |
| RC3 | 9.6, 153.6 | RC3 | 9.6, 307.2 | |
| RC4 | 9.6, 307.2 | |||
| RC5 | 14.4, 230.4 | RC4 | 14.4, 230.4 | |
| SR3 | RC6 | 9.6, 307.2 | RC5 | 9.6, 614.4 |
| RC7 | 9.6, 614.4 | |||
| RC8 | 14.4, 460.8 | RC6 | 14.4, 1036.8 | |
| RC9 | 14.4, 1036.8 |
RC1 and RC2 are similar to Rate Set 1 and 2 in IS-95. RCs are chosen such that the base rate for forward and reverse links match. If RC3 is used on the reverse link, either RC3 or RC4 can be used on the forward link.
Reverse Physical Channels
Common Channels:
- Reverse Pilot Channel: An un-modulated SS signal sent by each MS, allowing the BS to detect the corresponding uplink channel. Max 1 for SR1, Max 1 for SR3.
- Reverse Access Channel: Used for backward compatibility, for uplink common control signaling. Max 1 for SR1, NA for SR3.
- Reverse Enhanced Access Channel: A new channel used by MS to initiate communication or respond to BS when no dedicated channel is assigned to the user. Max 1 for SR1, Max 1 for SR3.
- Reverse Common Control Channel: Used for short burst data and signaling messages when traffic channels are not in use. Max 1 for SR1, Max 1 for SR3.
Dedicated Channels:
- Reverse Dedicated Control Channel: Similar to before. Max 1 for SR1, Max 1 for SR3.
- Reverse Fundamental Channel: Basic traffic channel that carries voice, low-rate data, and associated signaling messages. Max 1 for SR1, Max 1 for SR3.
- Reverse Supplemental Code Channel: Fixed rate data-only channel to provide higher transmission rate. Max 7 for SR1, NA for SR3.
- Reverse Supplemental Channel: Variable rate packet data channel carrying only high-speed coded information. Max 2 for SR1, Max 2 for SR3.
New Network elements in cdma2000
- MS: Additional features to support data services and enhanced signaling messages for both circuit-switched and packet-switched services.
- BS (BTS & BSC): Enhanced radio interface with significant hardware and software changes to provide voice, data, and multimedia traffic support.
π Definition β Packet Control Function (PCF): An entity that manages the buffering and relay of packets between the BS and PDSN. It maintains radio resource status (e.g., active, dormant) and collects radio link-related accounting information to be used by AAA.
π Definition β Packet Data Serving Node (PDSN): A new network entity acting as a Foreign Agent (FA) by providing routing services (maintaining routing tables and route discovery) according to Mobile IP. It manages the radio-packet (R-P) interface and PPP sessions for the MS, initiates authentication, authorization, and accounting (AAA) for mobile users, and can establish tunnels through public data networks using Layer 2 Tunneling Protocol (L2TP) to a VPN gateway. PDSN may optionally use IPSec to further protect the tunnel.
- Home Agent (HA): A network element within the mobile's home network. Its two major functions are mobile IP registration and packet forwarding. The HA interacts with AAA to receive authenticated mobile IP registration requests and return registration responses. It also forwards IP packets to and from the current point of attachment through the FA.
π Definition β AAA: Authentication, Authorization, and Accounting.
- Authentication: Verification of devices and subscribers for network access as well as user-based QoS requests.
- Authorization: Determines whether a user or device is authorized for a particular service with a specific QoS based on service profile. The requesting entity may cache authorization info.
- Accounting: Collecting and storing billing-related data concerning offered services, including session details (requested and offered QoS, duration of usage) and mobility records (dates and times of attach and detach).
Mobility Management for Packet Data Services
When an MS originates a call, messages are exchanged to establish and close an R-P connection between PCF/BSC and PDSN. Once a serial connection is established between MS and PDSN:
- MS and PDSN negotiate an authentication protocol according to Challenge Handshake Authentication Protocol (CHAP) or Password Authentication Protocol (PAP).
- PDSN sends authentication response to the AAA server, which decides whether to authenticate.
- PDSN constructs a Network Access Identifier (NAI) of the form MSID@realm (where realm is the home network domain).
- The user is identified as valid, and PDSN knows which IP service template to apply.
- When the PPP session is established, PDSN assigns the mobile an IP address from a pool of IP addresses.
- Routers in the packet network must route any packet with this IP to the PDSN serving the mobile.
Handoff
-
Intra-PCF Handoff: Supported by A8/A9 interfaces carrying user traffic and signaling between BS and PCF.
-
Inter-PCF and Intra-PDSN Handoff: Occurs when a location change causes the packet data session to divert from one R-P interface to another. A new R-P connection between the target PCF and serving PDSN is established, and the PPP session is moved. The previous R-P session is torn down. PCF-PCF handoff may occur while the MS is in active or dormant state. Dormant handoff is supported to maintain the PPP session while minimizing air-link resource usage. During an active session, PDSN supports low-latency handoff by bi-casting data to both the target and previous PCF.
-
Inter-PDSN Handoff: A network based on simple IP does not support mobility beyond a PDSN coverage area because a new IP address will be acquired from the new PDSN, making traffic on the existing IP undeliverable. This requires support for fast handoff using Mobile IP.
-
Inter-PDSN Fast Handoff: The target PDSN initiates establishment of a P-P session with the serving PDSN. The P-P interface is used to keep the PPP session anchored when PDSN-to-PDSN handoff is performed, allowing the existing PPP session to continue and reducing service interruption time and data loss.
β Key Takeaways
CDMA2000 is a 3G evolution of 2G CDMA that operates on 1.25 MHz channels, with 1xRTT supporting up to 307 kbps and 1xEV-DO supporting 2.4 Mbps dedicated to data. The physical layer uses Radio Configurations (RCs) to define data rates and modulation, with 7 RCs for reverse link and 9 for forward link. New network elements include PCF for buffering and relaying packets, and PDSN acting as a foreign agent managing PPP sessions and mobile IP routing. Mobility management uses PPP sessions with CHAP/PAP authentication, and handoff occurs at three levels: Intra-PCF, Inter-PCF/Intra-PDSN using R-P interfaces with bi-casting for low latency, and Inter-PDSN requiring Mobile IP with P-P sessions to anchor PPP connections.
π§ Quick Revision Questions
- What are the data rate capabilities of cdma2000 1xRTT and cdma2000 1xEV-DO?
- How many radio configurations exist for reverse and forward links in cdma2000, and what do they specify?
- What are the four common reverse physical channels and their primary functions?
- What are the three main functions of the AAA entity in cdma2000 networks?
- How does Inter-PDSN fast handoff reduce service interruption time compared to simple IP-based handoff?
π Lecture 25 β 1st Review
π Overview: This lecture serves as a comprehensive review of the entire CS718 Wireless Networks course, covering foundational concepts from Lectures 1 through 24. It systematically revisits key topics including wireless transmission fundamentals, multiple access techniques, cellular evolution from 1G to 4G, cellular system design, and specific technologies like AMPS, GSM, GPRS, EDGE, IS-95, UMTS/WCDMA, and cdma2000.
ποΈ Topics Covered
This review covers all major topics from the course: wireless vision, transmission fundamentals, encoding/modulation, noises, multiplexing, propagation modes, error detection and correction codes (Parity, CRC, Hamming, BCH, Reed-Solomon), ARQ protocols, multiple access techniques (FDMA, TDMA, CDMA, ALOHA, CSMA/CA), spread spectrum, 1G/2G/2.5G/3G/4G evolution, specifications of 2.5G and 3G standards, cellular concepts (frequency reuse, handoff, interference, trunking, Erlang), AMPS, GSM architecture and mobility, GPRS architecture and protocols, IS-95 forward and reverse channels, EDGE modulation and coding, UMTS/WCDMA architecture, spreading, scrambling, handover measurements, packet scheduling, and cdma2000 network elements and handoff types.
π Lecture Summary
Lecture 1 β Introduction Part I
Wireless communication begins with The Wireless vision connecting people anywhere. Radio Waves are electromagnetic waves used for transmission. Channel Capacity refers to the maximum data rate a channel can support. Signal-to-Noise Ratio (SNR) is the ratio of signal power to noise power, directly affecting capacity. The EM Spectrum spans from radio waves to gamma rays, with different bands allocated for different wireless services.
Lecture 1 β Introduction Part II
Wireless Transmission involves a baseband signal (original information signal) modulated onto a carrier frequency (high-frequency signal for transmission). The fundamental frequency determines the signal's basic period. Antenna size must correspond to the signal's wavelength: a 1 MHz signal requires a few hundred meters high antenna, while a 1 GHz signal requires only a few centimeters high antenna. Encoding/Modulation converts digital data into analog signals for transmission. Noises include Thermal noise (random electron motion), Intermodulation noise (from nonlinearities), Crosstalk (interference from adjacent paths), and Impulse noise (sudden spikes). Losses/Gain refer to signal attenuation or amplification during propagation.
Lecture 3 β Introduction Part III
Multiplexing combines multiple signals for transmission over a single medium. Transmission Mediums are Guided (wired like coaxial cable, fiber) and Unguided (wireless). Propagation modes include Ground wave (follows earth's surface), Sky wave (reflects off ionosphere), and LOS (Line-of-Sight, direct path). Multi-path propagation occurs when signals take multiple paths due to Reflection (bouncing off surfaces), Diffraction (bending around obstacles), and Scattering (spreading by small objects). Fading is the variation of signal strength over time and distance due to multipath.
Lecture 4 β Error Part I
Transmission Errors occur when bits are altered during transmission. Parity Check adds an extra bit (parity bit) to make the total number of 1s even or odd for basic error detection. Cyclic Redundancy Check (CRC) treats data as a polynomial and divides by a generator polynomial; the remainder is appended as CRC code. Block Error Code adds redundant bits to blocks of data for error detection and correction.
Lecture 5 β Error Part II
Block Codes include Hamming codes (can correct single-bit errors and detect double-bit errors), BCH codes (generalization of Hamming codes, can correct multiple errors), and Reed-Solomon codes (subclass of non-binary BCH codes, good for burst errors). ARQ (Automatic Repeat reQuest) uses acknowledgments and retransmissions: Sliding window allows multiple frames in transit, and Go-back-N retransmits all frames from the lost frame onward.
Lecture 6 β Multiple Access (Part I)
FDMA (Frequency Division Multiple Access) assigns different frequency bands to different users. TDMA (Time Division Multiple Access) assigns different time slots to different users. CDMA (Code Division Multiple Access) uses unique codes to allow simultaneous transmission on same frequency. Random Access includes ALOHA (transmit anytime, collision detection) and Slotted ALOHA (transmit only at slot boundaries, reducing collisions) and Reservation-based ALOHA (reserve slots before transmission).
Lecture 7 β Multiple Access (Part II)
CSMA (Carrier Sense Multiple Access) listens before transmitting. Versions of CSMA include 1-persistent, non-persistent, and p-persistent. CSMA/CA (Collision Avoidance) uses RTS/CTS handshake to avoid collisions, common in wireless.
Lecture 8 β Evolution Part I
1G wireless cellular networks include NMT (Nordic Mobile Telephone), AMPS (Advanced Mobile Phone System), and TACS (Total Access Communication System). Spread Spectrum includes Frequency Hopping (pseudorandomly changes carrier frequency) and Direct Sequence (spreads signal over wide bandwidth using chip code). 2G cellular systems include GSM (Global System for Mobile), IS-136 (D-AMPS), PDC (Pacific Digital Cellular), and IS-95 (cdmaOne).
Lecture 9 β Evolution Part II
2.5G technologies include HSCSD (High-Speed Circuit-Switched Data, up to 57.6 kbps), GPRS (General Packet Radio Service, up to 171.2 kbps), EDGE (Enhanced Data rates for GSM Evolution, up to 384 kbps), and IS-95B (up to 64 kbps). 3G technologies include UMTS/W-CDMA (Universal Mobile Telecommunications System/Wideband CDMA, up to 2 Mbps) and CDMA2000 (including 1xRTT at 144 kbps).
Specifications of 2.5G and 3G Standards
The table summarizes key specifications:
- HSCSD: Channel BW 200 KHz, FDD duplex, Software upgrade at BS only, No new spectrum, New handsets providing 57.6 kbps on HSCSD and 9.6 kbps on GSM
- GPRS: Channel BW 200 KHz, FDD duplex, New packet overlay at routers and gateways, No new spectrum, New GPRS sets work at 171.2 kbps
- EDGE: Channel BW 200 KHz, FDD duplex, New TX/Rx at BS with software upgrade, No new spectrum, Tri-mode sets (EDGE 384 kbps / GPRS 144 kbps / GSM 9.6 kbps)
- W-CDMA: Channel BW 5 MHz, FDD duplex, Completely new BS, New spectrum required, New handsets at 2 Mbps in WCDMA
- IS-95B: Channel BW 1.25 MHz, FDD duplex, New software at BS, No new spectrum, IS-95B at 64 kbps
- Cdma2000 1xRTT: Channel BW 1.25 MHz, FDD duplex, New software at backbone, new channel cards at BS, new packet service node, No new spectrum, 1xRTT at 144 kbps
- Cdma2000 1xEV(DO/DV): Channel BW 1.25 MHz, FDD duplex, Software and card upgrade to 1xRTT, No new spectrum, 1xEV at 2.4 Mbps
- Cdma2000 3xRTT: Channel BW 3.75 MHz, FDD duplex, Backbone modifications and channel cards at BS, May require new spectrum, 3xRTT at 2 Mbps
π‘ Why this matters: This table clearly shows the evolutionary path showing how 2.5G evolved from 2G through software/card upgrades while 3G required completely new infrastructure and spectrum.
Lecture 10 β Evolution III
Limitation of 3G includes limited data rates compared to emerging needs. 4G objectives include higher data rates, seamless mobility, and IP-based architecture. Issues include QoS (traffic from different services requires different cell loss rate, delay, and jitter guarantees β it is non-trivial across different networks), Security (involves authentication, confidentiality, integrity, authorization; heterogeneity complicates it; AAA protocols provide framework for control plane functions and installing security policies like encryption, decryption, and filtering), Multimedia Service, Applications, and Convergence of Cellular and WLAN with Billing Issue.
Lecture 11 β Cell Concept Part I
Cellular Concept divides coverage area into cells, each served by a base station with lower power. Frequency Reuse uses same frequencies in non-adjacent cells to increase capacity. Locating co-channel cells involves calculating distances between cells sharing same frequencies.
Lecture 12 β Cell Concept Part II
Channel Assignment Strategies include fixed and dynamic allocation. Handoff Strategies consider When to handoff (based on signal strength). In 1G, handoff is BS based (network decides). In 2G or today, handoff is Mobile-Assisted (mobile measures and reports). Prioritizing Handoff uses Guard channels concept (reserve channels for handoff) and Queuing handoff requests (delay if no channel available). Practical handoff considerations include Umbrella cell (large cell covering microcells) and Cell dragging (mobile holds signal too long).
Lecture 13 β Cell Concept Part III
Interference and system capacity includes Co-channel interference and capacity (caused by cells using same frequencies, reduces capacity) and Adjacent channel interference and capacity (caused by nearby frequencies leaking into desired channel). Channel Planning for Wireless System assigns frequencies to minimize interference.
Lecture 14 β Cell Concept Part IV
Trunking and Grade of Service involves Measuring Traffic Intensity (in Erlangs). Trunked Systems include Blocked Calls Cleared (lost call is dropped) and Blocked Calls Delayed (queued until channel available). Erlang Charts calculate probability of blocking/delay. Improving Coverage and Capacity uses Cell Splitting (divide cells into smaller cells), Sectoring (use directional antennas), Repeaters for Range Extension, and Microcell Zone Concept (central controller switches between microcell zones).
Lecture 15 β AMPS
AMPS (Advanced Mobile Phone System) is a 1G analog cellular system. System Overview uses FDMA/FDD. Call handling involves registration, paging, and channel assignment. Air interface specifies forward (base-to-mobile) and reverse (mobile-to-base) channels. Supervisory signals include SAT (Supervisory Audio Tone) and ST (Signaling Tone). N-AMPS is a narrowband version increasing capacity.
Lecture 16 β GSM
GSM (Global System for Mobile) is a 2G digital cellular standard. GSM System Architecture includes Mobile Station, Base Station Subsystem (BSS), Network and Switching Subsystem (NSS), and Operation Support Subsystem (OSS). GSM Network Areas include cell, location area, MSC area, and PLMN. Specifications include 200 KHz channel BW, 8 users per channel via TDMA. Subscriber Services include voice, SMS, and data. Mobility management uses HLR (Home Location Register) and VLR (Visitor Location Register).
Lecture 17 β GPRS (Part I)
GPRS (General Packet Radio Service) adds packet data to GSM. GPRS Architecture includes SGSN (Serving GPRS Support Node) and GGSN (Gateway GPRS Support Node). Registration and Session Management involves GPRS attach and PDP context activation. Routing Scenario in GPRS routes packets between MS and PDN. Channels Classification divides channels for signaling and traffic. PDP Context Activation establishes a packet data session with assigned IP address.
Lecture 18 β GPRS Part II
GPRS Protocol Architecture includes: MS β BSS (Um interface, radio protocols), BSS β SGSN (Gb interface), SGSN β GGSN (Gn interface), and GGSN β PDN (Gi interface). GPRS Air Interface uses packet data channels (PDCH). Data Routing and Mobility tracks mobile location. Uplink Data Transfer uses USF (Uplink State Flag) for contention resolution. Downlink Data Transfer uses polling method. QoS in GPRS defines reliability, delay, and throughput classes.
Lecture 19 β IS-95
IS-136 is a TDMA-based 2G standard (D-AMPS). CDMA/IS-95 is a 2G CDMA-based standard. Advantages include Higher capacity (soft capacity), Improved voice quality (new vocoder), Less power consumption (6-7 mW), Privacy (spreading codes), Graceful degradation (more users = gradual quality reduction, not hard blocking). Drawbacks include Self-jamming (interference from own cell users) and Near-far problem (strong signals from near users drown out far users). IS-95 Forward Channels include Pilot Channel (for synchronization and channel estimation), Sync Channel (for system timing), Paging Channel (for overhead and paging messages), and Traffic Channels (for user data). IS-95 Reverse Channels include access and traffic channels.
Lecture 20 β EDGE
EDGE (Enhanced Data rates for GSM Evolution) uses 200 KHz channels. Modulation and Coding Schemes (MCS-1 to MCS-9) use GMSK or 8-PSK modulation with different coding rates. Link Adaptation dynamically selects best MCS based on channel quality. Incremental Redundancy retransmits with different coding to combine for better decoding. Capacity Planning calculates throughput based on modulation and coding.
Lecture 21 β UMTS/WCDMA Part I
UMTS (Universal Mobile Telecommunications System) is a 3G standard. Service Classes include Conversational (real-time voice), Streaming (video), Interactive (web browsing), and Background (email, downloads). UTRAN Architecture includes Node B (base station) and RNC (Radio Network Controller) with two types: Serving RNC (controls the connection) and Drifting RNC (provides diversity handover support). Radio Interface Protocol Architecture has three layers: Physical, Data Link, and Network. Protocol Models for UTRAN define interfaces between network elements. Logical Channels are mapped to transport channels then to physical channels.
Lecture 22 β WCDMA Part II
Spreading and Scrambling uses channelization codes (for user separation) and scrambling codes (for cell/sector separation). Channel Concept has three layers: Logical Channels (RLC layer) β Transport Channels (MAC layer) β Physical Channels (Physical layer). Physical Layer Procedures include RACH Operation (mobile sends preamble of 16 symbols, waits for ACK on AICH - Acquisition Indicator Channel), Cell Searching uses 256 chip primary synchronization code and 15 secondary synchronization codes (SSCs), and Power Control uses Fast Closed Loop (1500 Hz TPC - Transmit Power Control commands, 1500 updates per second) and Closed Loop power control.
Lecture 23 β WCDMA Part III
Compressed mode measurements allow measuring other frequencies without dual receiver. Handover measurements include Intra-mode (same frequency), Inter-mode (different frequency in same system), and Inter-system (between UMTS and GSM). WCDMA packet data access uses shared channels for efficiency. Transport channels for packet data include Common (RACH, FACH), Dedicated (DCH), and Shared (DSCH, HS-DSCH) channels. Packet scheduling algorithms include Time division scheduling (assigns time slots), Code division scheduling (assigns spreading codes), and Transmission Power-based scheduling (allocates based on power budget).
Lecture 24 β CDMA2000
New MAC and Physical layer features improve data rates and efficiency. Physical layer of cdma2000 uses 1.25 MHz channels with QPSK/BPSK modulation. Reverse Physical channels include access, control, and traffic channels. New Network elements include Packet Control Function (PCF) (manages packet data connections at the BS) and Packet Data Serving Node (PDSN) (acts as gateway for packet data traffic). Mobility Management tracks mobile location across network. Handoff includes Intra-PCF (within same PCF), Inter-PCF/Intra-PDSN (between PCFs but same PDSN), and Inter-PDSN (between different PDSNs, requires mobile IP).
β Key Takeaways
The course covers the complete evolution of wireless networks from 1G analog systems (AMPS) through 2G digital (GSM, IS-95), 2.5G packet data (GPRS, EDGE), to 3G wideband systems (UMTS/WCDMA, CDMA2000). Fundamental concepts like cellular frequency reuse, handoff strategies, trunking theory with Erlang calculations, and multiple access techniques (FDMA, TDMA, CDMA, CSMA/CA) form the backbone of all cellular system design. Error control through block codes (Hamming, BCH, Reed-Solomon) and ARQ protocols ensures reliable transmission, while spread spectrum and CDMA principles enable higher capacity and graceful degradation. The transition from circuit-switched to packet-switched architecture (GPRS, cdma2000) with nodes like SGSN, GGSN, PCF, and PDSN marks the path toward all-IP 4G networks.
π§ Quick Revision Questions
- What is the difference between antenna size requirements for a 1 MHz signal versus a 1 GHz signal, and why?
- Compare the infrastructure changes required for upgrading from GSM to GPRS versus upgrading from GSM to W-CDMA.
- What are the three handoff types in cdma2000, and what distinguishes Inter-PCF/Intra-PDSN from Inter-PDSN handoff?
- How does the Guard Channels concept differ from Queuing handoff requests in prioritizing handoffs, and which trunking model (Blocked Calls Cleared or Delayed) does each relate to?
- Explain the difference between Spreading and Scrambling in WCDMA, including what each code type is used for.