π Lecture 23 β Modem Standards
π Overview: This lecture discusses the standards governing modems, including Bell modems and ITU-T V-series standards. It explains the technical limitations of traditional 33.6 Kbps modems due to quantization noise and introduces the 56K modem technology, which achieves higher download speeds by eliminating PCM quantization in one direction.
ποΈ Topics Covered
The lecture covers Bell modems and ITU-T modem standards, the technical explanation for the 33.6 Kbps limit in traditional modems based on PCM quantization, the architecture and data flow of 56K modems (uploading vs. downloading), and a brief introduction to cable modems.
π Lecture Summary
Modem Standards
The lecture opens by categorizing modem standards. Bell modems were the first commercial modems, developed in the early 1970s by Bell Telephone Co. The ITU-T (International Telecommunication Union β Telecommunication) V-series standards are the most popular today and are generally compatible with Bell modems (e.g., V.21, V.22, V.23, V.26, V.27, V.29). Intelligent modems, such as those from Hayes or Hayes-compatible modems, are controlled by instructions called AT commands, enabling features like automatic answering and dialing.
BELL Modems
(The lecture slide simply presents the heading "BELL Modems" without further text. This section serves as a heading for the subsequent detailed discussion on ITU-T and traditional modems.)
ITU-T Modems
(The lecture slide simply presents the heading "ITU-T Modems" without further text. This section serves as a heading for the subsequent detailed discussion.)
Traditional Modems
Traditional modems are limited to a data rate of 33.6 Kbps, as determined by Shannonβs formula: Data rate β Signal-to-noise ratio.
π Definition β PCM (Pulse Code Modulation): The process of converting an analog signal to a digital signal by sampling and quantizing it.
The transmission of data from point A to point B involves the following steps:
- Digital data is modulated by the modem at site A.
- Analog data is sent from the modem to the switching station at site A using the local loop.
- At the switching station, analog data is converted to digital using PCM.
- Digital data travels through the digital network of the telephone company and arrives at the switching station of site B.
- At the switching station, digital data is converted to analog using inverse PCM.
- Analog data is sent from the switching station at site B to the modem using the local loop.
- Analog data is demodulated by the modem at site B.
The limiting factor for data rate is step 3. Here, the analog signal is quantized to create a digital signal. The quantization noise resulting from this process limits the data rate to 33.6 Kbps. The transmission of data from site B to site A follows the same steps, and again the limiting factor is quantization.
π Result: The maximum data rate in each direction (upload and download) is limited to 33.6 Kbps.
56K Modems
If one side is an ISP (Internet Service Provider) and the signal does not have to pass through a PCM converter, quantization is eliminated in one direction, and the data rate can be increased.
Uploading (Transmission from subscriber to ISP) follows these steps:
- Digital data is modulated by the modem at site A.
- Analog data is sent from the modem to the switching station at site A on the local loop.
- At the switching station, data is converted to digital signal using PCM.
- Digital data travels through the digital network of the telephone company and is received by the ISP computer.
- The limiting factor is again step 3 (PCM quantization).
π‘ Why this matters: Users do not need a high data rate for uploading since small blocks of data (e.g., requests) are typically sent in this direction. Therefore, the 33.6 Kbps limit is acceptable.
Downloading (Transmission from ISP to subscriber) follows these steps:
- Digital data is sent by the computer of ISP through the digital telephone network.
- At the switching station, digital data is converted to analog using inverse PCM.
- Analog data is sent from the switching station at site A to the modem on the local loop.
- Analog data is demodulated by the modem at site A.
Note that in this direction, there is no quantization of data using PCM. The limitation when uploading is not an issue here. Data can be sent at 56 Kbps.
π‘ Why this matters: This is what the user wants, as larger files (e.g., web pages, videos) are typically downloaded from the internet.
π Result: The maximum data rate in the uploading direction is still 33.6 Kbps, but the data rate in the downloading direction is now 56 Kbps.
π Why 56 Kbps?: Switching stations of the telephone company use PCM/Inverse PCM for digitizing voice. The calculation is: 8000 samples/sec * 7 bits/sample = 56 Kbps.
Summary
The lecture concludes with a summary of MODEM Standards (Bell Modems, ITU-T Modems), Traditional MODEMS, 56k MODEMs, and a brief mention of Cable Modems (not covered in detail), pointing to reading sections from the textbook.
β Key Takeaways
The fundamental reason for the 33.6 Kbps speed limit in traditional modems is the quantization noise introduced by the Pulse Code Modulation (PCM) process at the telephone companyβs switching station. A 56K modem overcomes this limitation for downloading by having the sending device (the ISP) send a purely digital signal through the telephone network, bypassing the PCM conversion and its associated quantization noise. However, the upload direction from the subscriber to the ISP still passes through PCM, so its maximum rate remains at 33.6 Kbps. This asymmetric design is ideal for typical internet usage where users send small requests and receive large files.
π§ Quick Revision Questions
- What is the primary cause of the 33.6 Kbps data rate limit in traditional modems?
- In a 56K modem connection, why is the download speed higher than the upload speed?
- Describe the path of data during a download from an ISP to a subscriber's computer using a 56K modem.
- What is the significance of "quantization noise" in the context of PCM and modem data rates?
- What is the mathematical basis for the 56 Kbps data rate limit?
π Lecture 24 β Cable Modems
π Overview: This lecture introduces cable modems as a high-speed internet access technology that leverages the broad bandwidth of cable TV coaxial cables. It also begins a comprehensive exploration of transmission media, starting with guided media and a detailed focus on twisted-pair cable, its noise characteristics, and categories.
ποΈ Topics Covered
This lecture covers the operation and data rates of cable modems for downloading and uploading, defines electromagnetic energy and the electromagnetic spectrum. It then introduces the two classes of transmission media (guided and unguided), explores twisted-pair cable in depth including its noise immunity via twisting, categories (1-5), connectors, and advantages.
π Lecture Summary
Cable Modems
The data rate limitation of traditional modems is due to the narrow bandwidth (BW) of the local loop telephone line (4 kHz). Cable TV provides a coaxial cable with a BW of up to 750 MHz, divided into 6 MHz bands using FDM (Frequency Division Multiplexing). Two bands are set aside for internet access: one for downloading and one for uploading. A splitter directs TV bands to the TV set and internet bands to the PC.
π Definition β Cable Modem: A device that uses the broadband coaxial cable of a cable TV system to provide high-speed internet access.
Downloading: Requires a 6 MHz BW in the range above 40 MHz. It uses 64 QAM (Quadrature Amplitude Modulation), which sends 6 bits at a time. The theoretical data rate is 6 MHz * 6 = 36 Mbps, but PCs are not yet capable of this rate, so current rates are between 3 and 10 Mbps.
π Formula: Download Data Rate = Bandwidth * Bits per Signal Element β 6 MHz * 6 bits = 36 Mbps (theoretical)
Uploading: Requires a 6 MHz BW in the range below 40 MHz. At this low frequency, home appliances create noise that affects modulation. The technique used is QPSK (Quadrature Phase Shift Keying), which sends 2 bits at a time. The theoretical data rate is 6 MHz * 2 = 12 Mbps, but current uploading rates are between 500 Kbps and 1 Mbps.
π Example: A user uploads data using QPSK over a 6 MHz cable band. The theoretical rate is 6 MHz * 2 bits = 12 Mbps. However, due to noise from home appliances, the actual rate is much lower, around 500 Kbps to 1 Mbps.
Electromagnetic Energy
Signals are transmitted as electromagnetic energy, which can travel through vacuum, air, or other media. It is a combination of electrical and mechanical fields and includes power, voice, video, radio waves, infrared, visible light, and ultraviolet light. These constitute the electromagnetic spectrum. Not all portions are usable for telecommunications. Voice-band frequencies are typically transmitted as current over metal cables. Radio frequencies travel through air/space, and visible light is harnessed using fiber optic cable.
Classes of Transmission Media
There are two classes of transmission media:
- Guided Media: Provide a conduit from one device to another.
- Unguided Media
Twisted Pair Cable
Twisted pair cable comes in two forms: Unshielded Twisted Pair (UTP) and Shielded Twisted Pair (STP).
A twisted pair consists of two conductors (usually copper), each with its own colored plastic insulation for identification. This cable is the most common telecommunication medium today, suitable for both data and voice. Its frequency range is illustrated in the lecture.
π Definition β Twisted Pair Cable: A type of guided transmission medium consisting of two insulated copper wires twisted around each other to reduce electromagnetic interference.
Parallel Flat Wire vs. Twisted Pair: In the past, parallel flat wires were used, but electromagnetic (EM) interference from devices like motors created noise. With parallel wires, the wire closest to the noise source gets more interference, resulting in an uneven load and damaged signal. With twisted-pair, the wires are twisted around each other (2 to 12 twists per foot), so each wire is closer to the noise source for half the time. This equalizes the cumulative effect of interference.
π Example: In a twisted pair, if the top section of a twist has a "load" of 4 from noise and the bottom section has a load of 3, the total effect on one wire might be 14, and the total on the other wire is also 14, resulting in a net noise cancellation of 0 (14 - 14).
Advantages of UTP: UTP is cheap, flexible, and easy to install. Higher grades of UTP are used in LAN technologies like Ethernet and Token Ring.
Categories of UTP Cable: The EIA (Electronic Industries Alliance) has developed standards to grade UTP cables by quality, with 1 as the lowest and 5 as the highest.
- Category 1: Basic twisted-pair for telephone systems, inadequate for high-speed data.
- Category 2: Suitable for voice and data transmission up to 4 Mbps.
- Category 3: Requires at least 3 twists per foot, used for data transmission up to 10 Mbps. It is the standard for most telephone lines.
- Category 4: Requires at least 3 twists per foot, transmission rate of 16 Mbps.
- Category 5: Used for data transmission up to 100 Mbps.
UTP Connectors: UTP is connected to network devices via snap-in plugs. Connectors are male (plug) or female (receptacle). The most frequently used is the RJ 45 connector, which has 8 conductors, one for each wire in 4 twisted pairs.
π‘ Why this matters: Twisting wires is a simple, cost-effective way to dramatically reduce noise, a fundamental concept in all wired data communication.
β Key Takeaways
A student must remember that cable modems use the high bandwidth of cable TV lines for fast internet, with downloading using 64 QAM and uploading using QPSK due to lower frequency noise. The lecture transitions to transmission media, defining guided media that provide a physical conduit. The core of the lecture is on twisted-pair cable, where the key concept is twisting wires to cancel out electromagnetic interference, which is the primary advantage over parallel wires. The EIA categories (1-5) define the data rate capabilities of UTP cables, with Category 5 being the highest standard for most LAN applications, and the RJ-45 is the standard connector.
π§ Quick Revision Questions
- Why do cable modems offer higher data rates than traditional modems?
- What are the modulation techniques used for downloading and uploading data in a cable modem system, and why are they different?
- What is the primary advantage of twisting the two wires in a twisted-pair cable instead of having them parallel?
- List EIA UTP cable categories 3, 4, and 5, and their maximum data transmission rates.
- Which connector is most commonly used with UTP cable, and how many conductors does it have?
π Lecture 25 β Shielded Twisted Pair (STP)
π Overview: This lecture examines guided transmission media, focusing on Shielded Twisted Pair (STP), Coaxial Cable, and Optical Fiber. It explains how different cable types combat noise and crosstalk, the standards and connectors for coax, and the physics of light propagation through fiber optics for high-speed data transmission.
ποΈ Topics Covered
This lecture covers Shielded Twisted Pair (STP) cable and its noise/crosstalk shielding properties. It then details Coaxial Cable, its frequency range, RG standards, and connectors (BNC, T-connectors, terminators). Finally, it introduces Optical Fiber, explaining the nature of light, refraction, critical angle, reflection, and the two propagation modes: Multimode (Step-Index and Graded-Index) and Single Mode fiber.
π Lecture Summary
Shielded Twisted Pair (STP)
STP has a metal foil or braided-mesh covering that encases each pair of insulated conductors. This metal casing prevents the penetration of electromagnetic (EM) noise. It also can eliminate a phenomenon called Crosstalk, which is the undesired effect of one circuit (or channel) on another circuit (or channel). Crosstalk occurs when one line picks up some of the signals traveling down another line, such as hearing other conversations during a telephone call. Shielding each pair of twisted pair can eliminate most crosstalk. STP cable has the same quality considerations and uses the same connectors as UTP, but the shield must be connected to a ground. STP is more expensive than UTP but is less susceptible to noise.
π Definition β Crosstalk: The undesired effect of one circuit (or channel) on another circuit (or channel), where one line picks up signals from another.
π‘ Why this matters: STP provides a practical solution for environments with high electromagnetic interference, ensuring signal integrity at a higher cost.
Coaxial Cable
Instead of having two wires, coaxial cable has a central core conductor of solid or stranded wire (usually copper) enclosed in an insulating sheath. This is encased in an outer conductor of metal foil, braid, or a combination. The outer metallic wrapping serves both as a shield against noise and as the second conductor which completes the circuit. This outer conductor is enclosed in an insulating sheath, and the whole cable is protected by a plastic cover.
Frequency Range of Coaxial Cable
Coax carries signals of higher frequency ranges than twisted pair cable.
Coaxial Cable Standards
Different coaxial cable designs are categorized by their Radio Government (RG) ratings. Each RG number denotes a unique set of physical specifications, including the wire gauge of the inner conductor, the thickness and type of inner insulator, the construction of the shield, and the size and type of outer casing. Each cable defined by RG rating is adapted for a specialized function:
- RG-8: Used in Thick Ethernet
- RG-9: Used in Thick Ethernet
- RG-11: Used in Thick Ethernet
- RG-58: Used in Thin Ethernet
- RG-59: Used for TV
Coaxial Cable Connectors
A number of connectors have been designed for coaxial cable. The most common is the "BARREL connector" because of its shape. Of the barrel connectors, the most popular is the Bayonet Network Connector (BNC). The BNC connector pushes on and locks into place with a half turn. Other types of barrel connectors either screw together (requiring more effort to install) or push on without locking (less secure). Coaxial cables are familiar in Cable TV and VCR hookups that employ both threaded and slip-on style. Two other commonly used connectors are T-connectors and Terminators.
- A T-connector (used in Thin Ethernet) allows a secondary cable or cables to branch off from a main line.
- Terminators are required for bus topologies where one main cable acts as a backbone with branches to several devices but does not itself terminate in a device. If a main cable is left unterminated, any signal transmitted over the line echoes back and interferes with the original signal. A terminator absorbs the wave at the end and eliminates this echo.
π Definition β BNC Connector: A Bayonet Network Connector for coaxial cable that pushes on and locks into place with a half turn.
π Definition β Terminator: A device that absorbs the wave at the end of a cable in a bus topology to eliminate echo interference.
π Rule: [RG ratings] β Each RG number denotes a unique set of physical specifications.
Optical Fiber
Unlike conductive cables that transmit signals as current, optical fiber is made of glass or plastic and transmits signals in the form of light.
The Nature of Light
The speed of light is 300,000 Km/sec in a vacuum and depends on the density of the medium through which it is traveling. The higher the density, the slower the speed.
- Refraction: Light travels in a straight line through a single uniform structure. If a ray of light enters another substance of different density, its speed changes abruptly, causing a change in direction. This phenomenon is called Refraction. For example, a pencil in a glass of water appears bent because light changes direction moving from air to water.
- Direction of Refraction: A beam moving from a less dense to a more dense medium bends towards the vertical axis. The incident angle is 'I' and the refracted angle is 'R'.
- Critical Angle: When a beam moves from a more dense to a less dense medium, increasing the angle of incidence increases the angle of refraction. The angle at which the refracted line lies on the horizontal axis is called the Critical Angle.
- Reflection: When the angle of incidence becomes greater than the critical angle, reflection occurs. Light no longer passes into the less dense medium but is reflected back into the same medium. The Angle of Incidence (I) = Angle of Reflection (R).
- Optical Fibers & Reflection: Optical fibers use reflection to guide light through a channel. A glass or plastic CORE is surrounded by a CLADDING of less dense glass or plastic. The density difference is such that a beam of light moving through the core is reflected off the cladding. Information is encoded as a series of ON-OFF flashes representing 1 and 0 bits.
π Definition β Refraction: The phenomenon where a ray of light changes direction due to a change in speed when entering a medium of different density.
π Definition β Critical Angle: The angle of incidence at which the refracted line lies on the horizontal axis between two media.
Propagation Modes
Fiber technology supports two modes for the propagation of light: Multimode and Single Mode. Each requires fiber with different physical characteristics. There are two subcategories of Multimode Fiber: Multimode Step-Index Fiber and Multimode Graded-Index Fiber.
-
Multimode Fiber: Multiple beams from a light source move through the core in different paths.
-
Multimode Step-Index Fiber: The density of the core remains constant from center to edges. A beam moves in a straight line until it reaches the core-cladding interface. At the interface, there is an abrupt change to lower density, altering the beam's angle. The term "Step-Index" refers to the suddenness of this change. Some beams travel straight to the destination, some strike the interface at an angle smaller than the critical angle and are lost, and others hit the edge at angles greater than the critical angle and bounce back and forth.
-
Disadvantage of Multimode Step-Index Fiber: Each beam's angle equals its angle of reflection. If the incident angle (I) is small, the reflection angle (R) is small, requiring more bounces and more time to reach the destination. If I is large, R is large, and the beam reaches the destination quickly. This difference in path lengths results in distortion at the receiver, limiting the data rate and making this fiber inadequate for precise applications.
-
Multimode Graded-Index Fiber: This fiber solves the distortion problem with varying densities. Density is highest at the center of the core and decreases gradually to its lowest at the edge. The signal is introduced at the center of the core. Horizontal beams move straight to the receiver. Beams at other angles move through a series of constantly changing densities, causing each beam to refract into a curve. The signal can be reconstructed with far greater precision as all beams reach the receiver at almost the same time.
π Definition β Multimode Step-Index Fiber: A fiber with constant core density where the beam changes angle abruptly at the core-cladding interface.
π Definition β Multimode Graded-Index Fiber: A fiber with varying densities (highest at center, lowest at edge) that refracts beams into curves, ensuring almost simultaneous arrival and reducing distortion.
π Example β Multimode Step-Index Fiber Distortion: If a beam has a small incident angle (I), it takes more bounces and more time to travel the core compared to a beam with a large I. This time difference causes signal distortion.
β Key Takeaways
For the exam, you must understand that STP uses shielding to prevent noise and crosstalk, but is more expensive than UTP. Remember that coaxial cable uses RG ratings (e.g., RG-58 for Thin Ethernet) and requires proper connectors like BNC and terminators to prevent signal echo. The core physics of optical fiber relies on refraction and the critical angle; light reflects within the core when its incident angle exceeds the critical angle. Crucially, differentiate between Multimode Step-Index fiber (constant density, path length distortion) and Multimode Graded-Index fiber (varying density, reduced distortion). The key advantage of optical fiber over copper is its use of light for higher frequency and higher data rate transmission.
π§ Quick Revision Questions
- What is crosstalk and how does Shielded Twisted Pair (STP) cable reduce it?
- What does an RG rating denote for a coaxial cable, and what is the function of a terminator in a bus topology?
- Define refraction and the critical angle. What happens to a light ray when its angle of incidence exceeds the critical angle?
- What is the main disadvantage of Multimode Step-Index fiber, and how does Multimode Graded-Index fiber solve it?
- What are the two main propagation modes for optical fiber, and what physical characteristic (core density) distinguishes Step-Index from Graded-Index fiber?
π Lecture 26 β Single Mode Fiber
π Overview: This lecture covers fiber optic cable fundamentals, including single mode vs. multimode fiber, cable composition, light sources, connectors, and advantages/disadvantages. It then transitions to unguided media, focusing on radio wave propagation methods including surface, tropospheric, ionospheric, and line-of-sight propagation.
ποΈ Topics Covered
Single mode fiber characteristics, fiber sizes defined by core/cladding ratio, cable composition and materials, light sources (LED and LASER), fiber optic connectors and their importance, advantages and disadvantages of optical fiber compared to twisted pair and coaxial cable, unguided media introduction, radio frequency allocation into bands, and the four types of radio wave propagation: surface, tropospheric, ionospheric, and line-of-sight.
π Lecture Summary
Single Mode Fiber
Uses step index fiber and a highly focused source of light that limits beams to a small range of angles all close to the horizontal. Single mode fiber is manufactured with a much smaller diameter than multimode fiber. All of the beams arrive at the destination together and can be recombined without distortion to the signal.
Fiber Sizes
Optical fibers are defined by the ratio of the diameter of their Core to the diameter of their Cladding. Both diameters are expressed in Microns (Micrometers). Common fiber types include: 62.5/125 (core 62.5 microns, cladding 125 microns), 50/125, 100/140, and 8.3/125.
Cable Composition
A core is surrounded by cladding forming the fiber. In most cases, fiber is covered by a Buffer layer that protects it from moisture. Finally, the entire cable is encased in an outer jacket. Both core and cladding can be made of either glass or plastic but must be of different densities. The inner core must be ultra pure and completely regular in size and shape. Chemical differences in material and even small variations in the size or shape of the core alter the angle of reflection and distort the signals.
π Definition β Outer jacket materials: The outer jacket can be made of several materials including Teflon, Plastic, Fibrous Plastic, metal tubing. Each has a purpose: Plastic is lightweight and cheap but can emit fumes when burnt; Metal tubing provides strength but is costly; Teflon is lightweight and cheap but does not increase cable strength.
Light Sources for Optical Cable
For transmission to occur, the sending device must have a light source and the receiving device a photosensitive cell (Photodiode). The photodiode converts the light into current usable by the computer. The light source can either be an LED or an ILD (LASER).
π Definition β LED: Cheaper but provides Unfocused light that strikes the boundaries of the channel at uncontrollable angles. Limited to short distance use.
π Definition β LASER: Can be focused to a narrow range allowing control over angle of incidence.
Fiber Optic Connectors
If a connector is over tightened, two cores can be compressed and the angle of reflection of the signal will be altered. All popular connectors are Barrel shaped that come in male and female versions. The cable has a male connector that fixes into a female connector attached to the device to be connected.
Advantages of Optical Fiber
Noise Resistance: Because fiber uses light rather than electricity, noise is not a factor. External light is the only form of possible interference and is blocked from the channel by the outer jacket.
Less Signal Attenuation: Fiber optic transmission distance is significantly greater than other media. A signal can run miles without regeneration.
High Bandwidth: Can support higher bandwidths and higher data rates. High rates are not utilized by absence of signal generation and reception technology.
Disadvantages of Optical Fiber
COST: Expensive. No impurities or imperfections can be tolerated, so manufacturing is costly. Laser light sources can be expensive.
INSTALLATION: Roughness and cracking of core cannot be tolerated. All connections must be perfectly aligned.
Fragility: Glass fiber is very fragile. Cannot be used in extreme conditions where hardware portability is required.
Unguided Media
Unguided Media or Wireless Communication transport electromagnetic waves without a physical conductor. Instead, signals are broadcast through air and are available to anyone who has a receiver capable of receiving them.
Radio Frequency Allocation
The section of the EM spectrum defined as Radio Communication is divided into 8 ranges called BANDS. BANDS are rated from very low frequency (VLF) to extremely high frequency (EHF).
Propagation of Radio Waves
Radio wave transmission utilizes five different types of propagation: Surface, Tropospheric, Ionospheric, Line-of-Sight, and Space.
Radio Technology: Layers of Atmosphere
The earth is surrounded by two layers of atmosphere:
TROPOSPHERE: The portion of the atmosphere extending outwards approximately 30 miles from the earth's surface. It contains what we call AIR. Clouds, wind, temperature variation, and weather in general occur in the Troposphere, as does jet plane travel.
IONOSPHERE: The layer of atmosphere above the troposphere but below space. It is beyond what we think of as atmosphere.
Types of Propagation
Surface Propagation: Radio waves travel through the lowest layer of the atmosphere, hugging the earth. At the lowest frequencies, signals emanate in all directions from the transmitting antenna and follow the curvature of the planet. Distance depends on the amount of power in the signal.
Tropospheric Propagation: Can work in two ways:
- Line-of-Sight: A signal can be directed in a straight line from antenna to antenna. This method demands that both transmitter and receiver be placed within line-of-sight distances and is limited by the curvature of the earth.
- Broadcast: Signal is broadcasted at an angle into the upper layers of the troposphere from where it is reflected back to earth's surface. This method allows greater distances to be covered.
Ionospheric Propagation: Higher frequency radio waves are radiated toward the ionosphere where they are reflected back to the earth. The difference in density between troposphere and ionosphere causes each radio wave to speed up and change direction, bending back to earth. Allows greater distances to be covered by lower power output.
Line-of-Sight Propagation: Very high frequency signals are transmitted in straight line from antenna to antenna. Antennas must be directional, facing each other or either tall enough or close enough to avoid earth's curvature. Radio waves can reflect off objects in the middle and can reach late to the receiver. These late signals distort the signal.
Space Propagation: A broadcast signal is received by orbiting satellites which rebroadcast the signal to the intended receiver on the earth.
β Key Takeaways
Single mode fiber uses a highly focused light source with a small core diameter, allowing all beams to arrive together without distortionβunlike multimode fiber. Fiber optic cables consist of core, cladding, buffer, and outer jacket, with core and cladding made of glass or plastic of different densities. LEDs are cheap but produce unfocused light for short distances, while LASERs produce focused, narrow beams for long-distance transmission. Optical fiber offers noise resistance, low attenuation, and high bandwidth, but is expensive, fragile, and requires precise installation. For unguided media, radio waves propagate via surface, tropospheric (line-of-sight and broadcast), ionospheric, and space propagation methods, each with distinct characteristics depending on frequency and atmospheric layers.
π§ Quick Revision Questions
- What is the key difference between single mode and multimode fiber in terms of beam angles and signal distortion?
- What is the meaning of "62.5/125" when describing fiber size?
- What are the two types of light sources used in optical fiber transmission, and which one produces focused light?
- List three advantages and three disadvantages of optical fiber over twisted pair and coaxial cable.
- Name the four types of radio wave propagation discussed in this lecture, and briefly describe one characteristic of each.
π Lecture 27 β Propagation of Specific Signals
π Overview: This lecture covers the propagation characteristics of radio signals across different frequency bands, from VLF to EHF. It then explores terrestrial microwave communication, satellite communication systems, cellular telephony operations, and introduces transmission impairments including attenuation and distortion. Understanding these concepts is essential for designing effective wireless communication systems.
ποΈ Topics Covered
The lecture begins by explaining how each radio frequency band (VLF through EHF) propagates through different atmospheric layers and their specific applications. It then covers terrestrial microwave communication including repeaters and antenna types (parabolic dish and horn). The discussion continues with satellite communication, focusing on geosynchronous satellites and frequency bands (C, Ku, Ka), followed by cellular telephony operations including transmitting, receiving, and handoff. The lecture concludes with transmission impairments, particularly attenuation measured in decibels and signal distortion.
π Lecture Summary
Propagation of Specific Signals
The type of propagation used in radio transmission depends upon the frequency of the signal. Each frequency is suited for a specific layer of atmosphere and is most efficiently transmitted and received by technologies adapted to that layer.
Very Low Frequency (VLF): VLF waves are propagated as surface waves through air. They do not suffer much attenuation in TX but are susceptible to high levels of atmospheric noise (electricity and heat). Used for long-range radio navigation and submarine communication.
Low Frequency (LF): Also propagated as surface waves. Used for long-range radio and for navigational locators. Attenuation is greater in the day time when absorption of waves by natural obstacles increases.
Middle Frequency (MF): Propagated in the Troposphere. These frequencies are absorbed by the Ionosphere. The distance they cover is limited by the angle needed to get the signal to reflect from the troposphere and not enter the ionosphere. Absorption increases during the day time. Used for AM Radio.
High Frequency (HF): Use ionospheric propagation. These frequencies move into the ionosphere where the density difference reflects them back on earth. Used for Citizenβs Band Radio, International Broadcasting, Military Communication, Telephone, Telegraph and Fax.
Very High Frequency (VHF): Most VHF waves use line-of-sight propagation. Used for VHF Television, FM Radio, Aircraft AM Radio.
Ultra High Frequency (UHF): Always use line-of-sight propagation. Used for UHF Television, Mobile Telephone, Cellular Radio, Paging, Microwave Links. Note that microwave communication begins at 1GHz in UHF and continues into SHF and EHF band.
Super High Frequency (SHF): SHF waves are TX using mostly line-of-sight and some space propagation. Used for Terrestrial and Satellite Microwave and Radar Communication.
Extremely High Frequency (EHF): Use space propagation. Used for Radar, Satellite and Experimental Communication.
Terrestrial Microwave
Microwaves do not follow the curvature of earth and therefore require line-of-sight TX and RX equipment. Distance covered by line-of-sight signal depends to a large extent on the height of the antennas. Height allows the signal to travel farther by crossing obstacles like low hills and buildings. Microwave signals propagate in one direction at a time, meaning two frequencies are necessary for 2-way communication (e.g., telephone conversation). One frequency is reserved for microwave communication in one direction and the other for TX in the other direction. Each frequency requires its own transmitter & receiver combined in a transceiver nowadays.
Repeaters: To increase distance for terrestrial microwave, a system of repeaters can be installed with each antenna. A signal received by one antenna can be converted back to the transmittable form and relayed to the next antenna. The distance required between repeaters varies with frequencies of the signal and the environment. A repeater may broadcast the regenerated signal either at original frequency or a new frequency depending on system. Used in telephone systems worldwide.
Antennas: Two types of antennas are used for microwave communication: Parabolic Dish and Horn.
Parabolic Dish: Based on the geometry of a parabola. Every line parallel to the line of symmetry (line of sight) reflects off the curve at an angle such that they intersect in a common point called FOCUS. A parabolic dish works like a funnel catching a wide range of waves and directing them to a common point. In this way most of the signal is recovered than would be possible with a single-point receiver.
Horn: Outgoing transmissions are broadcast through a horn aimed at the dish. The microwaves hit the dish and are deflected outward in a reversal of the receipt path. A horn antenna looks like a gigantic scoop. Outward TXs are directed upward a stem and are deflected outward in a series of narrow parallel beams.
Satellite Communication
Satellite TX is much like line-of-sight transmission in which one of the stations is the satellite orbiting around the earth. The principle is similar to terrestrial microwave with a satellite acting as a super tall antenna and repeater. Although in satellite TX, signals must still travel in straight line, the limitations imposed on distance by curvature of earth are reduced. Satellites can span continents and oceans with one bounce off the satellite. Satellites can provide TX capability to and from any location on earth no matter how remote. This advantage makes high quality communication available to underdeveloped parts of the world at almost no cost. Satellites themselves are very expensive but leasing a frequency or time on one can be cheap.
Geosynchronous Satellite: Line-of-sight propagation requires the sending and receiving antennas must be locked into each other. To ensure continuous communication, satellites must move with the same speed as earth so that they seem fixed with respect to earth. These satellites are called Geosynchronous Satellites. Three satellites in geosynchronous orbit each 120 degrees from one another can cover the whole earth.
Satellite Frequency Bands: Each satellite sends and receives over two bands: Uplink (from earth to satellite) and Downlink (from satellite to earth).
| Band | Downlink | Uplink |
|---|---|---|
| C | 3.7-4.2 GHz | 5.925-6.425 GHz |
| Ku | 11.7-12.2 GHz | 14-14.5 GHz |
| Ka | 17.7-21 GHz | 27.5-31 GHz |
Cellular Telephony
Each service area is divided into small ranges called cells. Each cell office is controlled by a switching office called MTSO (Mobile Telephone Switching Office).
Transmitting: Mobile phone sends the number to the closest cell office β Cell office β MTSO β Telephone office. MTSO assigns an unused voice channel.
Receiving: Telephone office sends the signal to MTSO. MTSO sends queries to each cell (paging). If mobile phone is found and available, assigns a channel.
Handoff: MTSO monitors the signal level every few seconds. If the strength diminishes, MTSO seeks a new cell and changes the channel carrying the call.
Transmission Impairments
Transmission media are not perfect. What is sent is not what is received.
Attenuation: Attenuation means loss of energy. Some electrical energy is converted to heat.
π Definition β Decibel (dB): Relative strengths of two signals or a signal at two points.
π Formula: dB = 10 logββ (Pβ/Pβ) where Pβ and Pβ are signal powers. Negative dB means attenuation. Positive dB means amplification.
π Example 7.1: Imagine a signal travels through a transmission medium and its power is reduced to half. This means Pβ = (1/2)Pβ. Calculate Attenuation?
- 10logββ(Pβ/Pβ) = 10logββ(0.5Pβ/Pβ) = 10(-0.3) = -3 dB
π‘ Why this matters: The decibel scale allows engineers to express very large or very small power ratios in a manageable way, making it easier to calculate signal loss across a communication system.
Distortion: Distortion means that the signal changes its form or shape. Distortion occurs in a composite signal.
β Key Takeaways
Students must remember the propagation characteristics of each frequency band (VLF through EHF) and their specific applications. For terrestrial microwave, the key concepts are line-of-sight propagation, the role of antenna height, the need for two frequencies for bidirectional communication, and the function of repeaters. In satellite communication, geosynchronous satellites orbit at earth's rotation speed to appear fixed, with three satellites covering the entire globe using C, Ku, and Ka bands for uplink and downlink. Cellular telephony operations involve three key processes: transmitting, receiving, and handoff, all managed by the MTSO. Finally, transmission impairments include attenuation (measured in decibels, with -3 dB representing half power) and distortion, which changes signal shape.
π§ Quick Revision Questions
- Which frequency bands use line-of-sight propagation and which use surface wave or ionospheric propagation?
- Why are two frequencies required for bidirectional terrestrial microwave communication?
- How does a parabolic dish antenna focus signals and why is this beneficial?
- What is the purpose of a geosynchronous satellite and how many are needed for global coverage?
- If a signal's power is reduced to one-fourth of its original value, what is the attenuation in dB?
π Lecture 28 β Transmission Impairments
π Overview: This lecture examines the imperfections in transmission media that cause signals to degrade or change as they travel from sender to receiver. It covers the four main types of impairments (attenuation, distortion, and noise), defines key performance metrics like throughput and propagation time, introduces the concept of wavelength, and presents the Shannon Capacity formula for determining theoretical maximum data rates. Finally, it compares different media based on cost, speed, attenuation, EMI, and security.
ποΈ Topics Covered
This lecture covers transmission impairments including attenuation (measured in decibels), distortion, and the four types of noise (thermal, induced, crosstalk, impulse). It then moves to performance measurement concepts: throughput, propagation speed, and propagation time. The wavelength concept linking frequency and propagation speed is introduced. The Shannon Capacity formula is presented for calculating theoretical channel capacity. Finally, five factors for media comparison are discussed: cost, speed, attenuation, EMI, and security.
π Lecture Summary
Transmission Impairments
Transmission media are not perfect. Imperfections cause impairments in the signal as it travels through the medium. This means the signal at the beginning and the end of the medium are not the same β what is sent is not what is received.
Attenuation
Attenuation is the loss of energy a signal experiences as it travels through a medium. When a signal travels through a medium, it loses some of its energy to overcome the resistance of the medium. This is why wires carrying electric signals get hot β some of the electrical energy in the signal is converted to heat. To compensate for this loss, amplifiers are used to amplify the signal.
Decibel (dB) measures the relative strength of two signals or a signal at two different points.
π Definition β Decibel (dB): A logarithmic measure of the relative strength of two signals or a signal at two different points. π Formula: dB = 10 logββ (Pβ/Pβ) β dB is negative if a signal is attenuated (loss), dB is positive if a signal is amplified (gain).
π Example 7.1: Imagine a signal travels through a transmission medium and its power is reduced to half. This means Pβ = (1/2)Pβ. Calculate Attenuation? Solution: dB = 10 logββ (Pβ/Pβ) = 10 logββ (0.5 Pβ/Pβ) = 10 (-0.3) = -3 dB (Negative dB means attenuation)
Distortion
Distortion means that the signal changes its form or shape. Distortion occurs in a composite signal (made of different frequencies). Each signal component has its own speed in the medium, causing the signal to change shape as it propagates.
Noise
Noise refers to unwanted signals that interfere with the original transmitted signal. There are four types:
- Thermal Noise: Due to random motion of electrons in a wire that creates an extra signal not originally sent by the transmitter. It is always present.
- Induced Noise: Comes from external sources like motors and appliances.
- Crosstalk: The effect of one wire on another (signal from one wire induces a signal in an adjacent wire).
- Impulse Noise: A spike (a signal with high energy in a very short period of time) that comes from power lines, lightning, etc.
π‘ Why this matters: Noise is a fundamental limit on communication quality. Understanding its sources helps engineers design systems that are more robust and reliable.
Performance of Medium
Three concepts are used to measure the performance of transmission media: Throughput, Propagation Speed, and Propagation Time.
- Throughput: Measurement of how fast data can pass through a point. In other words, if we consider any point in the transmission medium as a wall through which bits pass, then throughput is the number of bits that can pass this wall in one second.
- Propagation Speed: Measures the distance a signal or a bit can travel through a medium in one second. The propagation speed of EM signals depends on the medium and the frequency of the signal.
- Propagation Time: Measures the time required for a signal (or a bit) to travel from one point of the transmission medium to another.
π Formula β Propagation Time: Propagation time = Distance / Propagation Speed.
Wavelength
Wavelength is another characteristic of a signal traveling through the transmission medium. This concept binds the frequency of the signal to the propagation speed of the medium. It is customary to talk about wavelength when talking about transmission of light in optical fiber. The wavelength is the distance a simple signal can travel in one period.
π Formula: Wavelength = Propagation speed Γ Period = Propagation speed / Frequency
Shannon Capacity
In 1944, Claude Shannon introduced a formula to determine the theoretical highest data rate for a channel.
π Formula β Shannon Capacity: C = B logβ (1 + S/N) in bps
- B: bandwidth of the channel (in Hz)
- S/N: signal-to-noise ratio (unitless, power ratio)
π Example (Extremely noisy channel): S/N β 0. Then C = B logβ (1 + 0) = 0 bps. No data can be sent over a completely noisy channel.
π Example (Telephone line): Bandwidth is 3000 Hz, S/N ratio is 3162 (which is 35 dB). Then C = 3000 logβ (1 + 3162) = 34,860 bps.
π‘ Why this matters: The Shannon Capacity gives the absolute upper limit on data rate for a given channel. It is a fundamental law of information theory that cannot be exceeded.
Media Comparison
When evaluating the suitability of a particular medium to a specific application, five factors should be kept in mind:
- Cost: This is the cost of materials plus installation.
- Speed: Speed is the maximum number of bits per second that a medium can transmit reliably. Speed varies with frequency, with the physical size of the medium, and with transmission equipment.
- Attenuation: Tendency of an EM signal to become weak or distorted over distance.
- EM Interference (EMI): EMI is the susceptibility of the medium to external EM energy introduced into the link that interferes with the intelligibility of a signal. Familiar effects of EMI are static (audio) and snow (visual).
- Security: How easy it is for an unauthorized device to listen on the link? Twisted pair is interceptable; optical fiber is more secure.
β Key Takeaways
- Transmission impairments (attenuation, distortion, and noise) cause the received signal to differ from the sent signal β perfect transmission is impossible. 2. Attenuation is measured in decibels (dB), where negative dB indicates signal loss and positive dB indicates amplification. 3. Throughput, propagation speed, and propagation time are three critical metrics for measuring transmission medium performance. 4. The Shannon Capacity formula (C = B logβ(1+S/N)) defines the absolute theoretical maximum data rate for any noisy channel. 5. Media are compared on five factors: cost, speed, attenuation, electromagnetic interference susceptibility, and security β each medium has trade-offs for different applications.
π§ Quick Revision Questions
- What is attenuation, and why does it cause wires to get hot?
- Calculate the dB value if a signal's power is amplified to 10 times its original value.
- What is the difference between propagation speed and throughput?
- A channel has a bandwidth of 4000 Hz and an S/N ratio of 100. What is its Shannon Capacity?
- List the four types of noise and give one example source for each.